spare parts for the Trabant front axle left and right hand

The product category Trabant 601 > Spare parts > Front axle > steering knuckles & wishbone is spread over 5 sites:

Outer wishbone bearing

Bottom bearing for the connection between steering knuckle and wishbone Trabant front axle. Inclusive bushing for king pin (plastic) and grease nipple.
The plasic bushing have to be crinded after the king pin diameter (an tool like reamer will be helpfully for this work)

material: iron
fit for Trabant 500,600,601
made in EU
for each wheel side will be one piece needed

96,39 €inclusive VAT, plus shipping costs

Delivery in 1-3 days

Art.No. 910

Bushing for king pin

Detail

Plastic bushing for king pin (bottom joint of the front axle). It have to be pressed in from top of the outer wishbone bearing and after that the bushing have to be crinded like the outside diameter of the king pin. (reamer).
The material Miramid is an special plastic with brilliant slipping features.

made in EU
for each wheel side one piece will be needed

9,64 €inclusive VAT, plus shipping costs

Delivery in 1-3 days

Art.No. 911

Grease cap for king pin

Detail

Plastic grease cap to protect the king pin bearing.
Material: plastic with hole for controlling lubrication of king pin bushing

made in Germany
original spare part
two pieces will be needed

3,95 €inclusive VAT, plus shipping costs

Delivery in 1-3 days

Art.No. 6207

King pin ( single part )

Detail

Pin for the bottom side of the Trabant front axle right and left hand.
Delivery as an single part without any mounting parts.
The king pin have to be pressed at the fornt steering knuckle and have to be fixed by an notched tapered pin.
material: steel
survace: 22 H7
best quality with circumferentially greace groove.

35,00 €inclusive VAT, plus shipping costs

Delivery in 1-3 days

Art.No. 912

King pin, repair set

Detail

Complete set, inclusive 1x king-pin, 1x bushing for king pin, 1x seal for king pin, 1x rubber cap for outer wishbone bearing and 1x safety nut for kin pin.
For each axle you need one set.
Fit to Trabant 500, 600, 601

39,36 €inclusive VAT, plus shipping costs

Delivery in 1-3 days

Art.No. 913

Notched tapered pin

Detail

the notched tapered pin will be pressed in the steering knuckle to secure the king pin.
Be careful, do not use the notched tapered pin twice!

8 x 32mm
for each king pin one piece will be needed

1,34 €inclusive VAT, plus shipping costs

Delivery in 1-3 days

Art.No. 916

Sealing ring for king pin

Detail

Rubber sealing ring to protect the lower bearing of the front axle Trabant.
Sealing between axle case and king pin bushing against dust and moisture.
This new produced sealing consist like the orignal one of an V-ring and one pressure O-ring.
All parts are made in Germany and will be the best replacemant for the original one.
scope of delivery:

1x rubber V-ring to protect the bearing
1x O-ring
made in Germany
grease resistant rubber
two pieces will be needed

Made in Germany

3,90 €inclusive VAT, plus shipping costs

Delivery in 1-3 days

Art.No. 914

Washer for king pin 0,2mm

Detail

Spezial washer for adjusting the bearing gap between the Outer wishbone bearing and the king pin.
Empirically different thickness will be needed for an precise adjustment.

material: chadded sheet matal
outside diameter: 20,9 mm
inside diameter: 15 mm
thickness: 0,2 mm
fit to all Trabant 500, 600 and 601

0,24 €inclusive VAT, plus shipping costs

Delivery in 1-3 days

Art.No. 915

Washer for king pin 0,5mm

Detail

Spezial washer for adjusting the bearing gap between the Outer wishbone bearing and the king pin.
Empirically different thickness will be needed for an precise adjustment.

material: chadded sheet matal
outside diameter: 20,9 mm
inside diameter: 15 mm
thickness: 0,5 mm
fit to all Trabant 500, 600 and 601

0,24 €inclusive VAT, plus shipping costs

Delivery in 1-3 days

Art.No. 6523

Washer for king pin 1,0mm

Detail

Spezial washer for adjusting the bearing gap between the Outer wishbone bearing and the king pin.
Empirically different thickness will be needed for an precise adjustment.

material: chadded sheet matal
outside diameter: 21 mm
inside diameter: 14,5 mm
thickness: 1,0 mm
fit to all Trabant 500, 600 and 601

0,88 €inclusive VAT, plus shipping costs

Delivery in 1-3 days

Art.No. 6524

The product category Trabant 601 > Spare parts > Front axle > steering knuckles & wishbone is spread over 5 sites:

1 2 3 4 5
Show all products

* All prices inclusive VAT and plus shipping costs.