spare parts for the Trabant front axle left and right hand

The complete offer in spare parts for the Trabant front axle left and right hand

Steering knuckle left hand, old driven shaft

Complete component of the front axle steering knuckle left hand. Can be used for the old driven shaft of Trabant601 up to vintage april 1984.
Scope of delivery:

drum brake base plate
king pin
bushing for spring yoke
original spare part, greased

290,00 €inclusive VAT, plus shipping costs

Delivery in 1-3 days

Art.No. 885

Steering knuckle right hand, old driven shaft

Detail

Complete component of the front axle steering knuckle right hand. Can be used for the old driven shaft of Trabant601 up to vintage april 1984.
Scope of delivery:

drum brake base plate
king pin
bushing for spring yoke
original spare part, greased

290,00 €inclusive VAT, plus shipping costs

Delivery in 1-3 days

Art.No. 886

Steering knuckle left hand, new driven shaft, T601

Detail

Complete component of the front axle steering knuckle left hand. Can be used for constant velocity drive shaft of Trabant601 from vintage april 1984.
Scope of delivery:

drum brake base plate
king pin
bushing for spring yoke
original spare part, greased

550,00 €inclusive VAT, plus shipping costs

Delivery in 1-3 days

Art.No. 887

Steering knuckle right hand, new driven shaft

Detail

Complete component of the front axle steering knuckle right hand. Can be used for constant velocity drive shaft of Trabant601 from vintage april 1984.
Scope of delivery:

drum brake base plate
king pin
bushing for spring yoke
original spare part, greased

550,00 €inclusive VAT, plus shipping costs

Delivery in 1-3 days

Art.No. 888

Steering knuckle left hand, new universal shaft upgrade1

Detail

upgraded steering knuckle for new driven shaft Trabant 601
fit to left side (driver side)
with black finish
Please send an overhaulable steering knuckle left hand to our company in advance for overhauling.

complete with:
brake base plate, king pin complete with outer wishbone bearing, spring yoke complete mounted and adjusted, grease nipple, new wheel bearing, steering knuckle leaver und brake line retainer.

delivery without:
brake shoes, wheel brake cylinders, release springs, support for brake shoes, sliding elemets, wheel hub, brake drum and universal shaft

Please send an overhaulable steering knuckle left hand to our company in advance for overhauling.

485,00 €inclusive VAT, plus shipping costs

Delivery in 14 days.

Art.No. 6469

Steering knuckle right hand, new universal shaft upgrade1

Detail

Upgraded steering knuckle for new driven shaft Trabant 601
fit to right side (co-driver side)
Please send an overhaulable steering knuckle right hand to our company in advance for overhauling.

complete with:
brake base plate, king pin complete with outer wishbone bearing, spring yoke complete mounted and adjusted, grease nipple, new wheel bearing, steering knuckle leaver und brake line retainer.

delivery without:
brake shoes, wheel brake cylinders, release springs, support for brake shoes, sliding elemets, wheel hub, brake drum and universal shaft

Please send an overhaulable steering knuckle right hand to our company in advance for overhauling.

485,00 €inclusive VAT, plus shipping costs

Delivery in 14 days.

Art.No. 6468

Steering knuckle right / left hand complete overhouled ()

Detail

The price is for one pair (1x left and 1x right hand). Complete pre-finished. Version for Trabant 601 form vintage April 1984.
scope of delivery:

2x spring yoke and king pin new
2x new outer wishbone
all bushings are changed
2x brake drum und 4x brake shoes
4x wheel brake cylinder
2x wheel bearings
bits and pieces

The steering knuckle will be sand blasted and with two K-colour varnished (black).

780,94 €inclusive VAT, plus shipping costs

Delivery in 14 days.

Art.No. 889

Repairkit front axle bushing

Detail

One set of bushings for king pin and spring yoke front axle.
Scope of delivery:

1x upper bushing for spring yoke
1x lower bushing for spring yoke
1x bushing for kin pin
1x sealing for Spring yoke
1x sealing for king pin (part.-No.:914)
2x plastic washer spring yoke
2x plastic washer wishbone
2x grease cape king pin / spring yoke (part.-No.:927)

made in EU
2 piece will be needed

additional needed speacial tools for assembly:

Hand reamer 22-H7
Hand reamer 20-H7

20,44 €inclusive VAT, plus shipping costs

Delivery in 1-3 days

Art.No. 8462

Padded nipple for outer wishbone bearing

Detail

Padded nipple for the outer wishbone bearing and the steering knuckle. Fit to all Trabant with two stroke engine like 500, 600, 601.

Gtap size: M6 x 1,0
made in Germany
all in all four pieces will be needed

1,08 €inclusive VAT, plus shipping costs

Delivery in 1-3 days

Art.No. 900

Grease cap hinge shaft drive

Detail

Grease pot for mounting at the steering knuckles to protect the outer drive shaft hinges left and right hand.
Fit tor Trabant 601 with two M5 mounting screws.
Connection thread for padded nipple M6.

original spare part
material: steel
delivery without any mounting bits
all in all two pieces will be needed

26,33 €inclusive VAT, plus shipping costs

Delivery in 1-3 days

Art.No. 7885

Padded nipple A 6 ( M6 x 1,0 ), stainless steel

Detail

Grease nipple made of stainless stell for the outer wishbone bearing and the steering knuckle. Fit to all Trabant with two stroke engine like 500, 600, 601.

Gtap size: M6 x 1,0
made in Germany
all in all four pieces will be needed

1,90 €inclusive VAT, plus shipping costs

Delivery in 1-3 days

Art.No. 7726

Brake hose retainer for Steering knuckle leaver left hand

Detail

metal holder for the fron brake hose at the Trabant 500, 600 and 601 front axle right hand (driver side).
Mouning at the rear side of the steering knuckle leaver bolt.
The retainer will also used at the lock plate for this screw connection.

original spare part
material: steel
delivery without any mounting bits
one piece will be needed

9,55 €inclusive VAT, plus shipping costs

Delivery in 1-3 days

Art.No. 7994

Brake hose retainer for Steering knuckle leaver right hand

Detail

metal holder for the fron brake hose at the Trabant 500, 600 and 601 front axle right hand (codriver side).
Mouning at the rear side of the steering knuckle leaver bolt.
The retainer will also used at the lock plate for this screw connection.

original spare part
material: steel
delivery without any mounting bits
one piece will be needed

9,55 €inclusive VAT, plus shipping costs

Delivery in 1-3 days

Art.No. 7993

Steering knuckle, left / right hand, compete with rubber cushions

Detail

Front wishbone complete inclusive all rubber cushions (2x inner bushing connection to the underframe and 2x bushing connection to the outher wishbone. Fit to Trabant 601 front axle right and left hand. Latest version without cover plate for savety bar.

surface basic coulored, grey
new produced, made in EU
two pieces will be needed for one car

84,22 €inclusive VAT, plus shipping costs

temporary not available

Art.No. 902

Outer rubber cushion ( 12 x 32 )

Detail

Outer rubber cushion for steering knuckle left or right hand,

inside diameter: 12 mm
length: 32 mm
for Trabant 500, 600 and 601
2 pieces will be needed for each whisbone

5,37 €inclusive VAT, plus shipping costs

Delivery in 1-3 days

Art.No. 903

Inner rubber cushion ( 12 x 44 )

Detail

Inner rubber cushion for steering knuckle left or right hand.

inside diameter: 12 mm
length: 44 mm
for Trabant 500, 600 and 601
2 pieces will be needed for each wishbone

6,19 €inclusive VAT, plus shipping costs

Delivery in 1-3 days

Art.No. 904

Bolt for steering knuckle front axle

Detail

Steel bolt for connection between steering knuckle and outer wishbone bearing.
Type with adjusting slot and semicircle for clipbolt
Made in Germany

turning moment: 75 Nm
grade: 10.9
tap: M10 on both ends
total length: 135 mm
fit to Trabant 500, Trabant 600 and Trabant 601
galvaniced
for each front axle one piece will be needed (total 2 pieces)

15,29 €inclusive VAT, plus shipping costs

Delivery in 1-3 days

Art.No. 905

Bolt for inner rubber cushion wishbone

Detail

Bolt for inner inner rubber cushion wishbone Trabant 500, 600, 601 front axle left or right hand.

incl. retaining ring and nut
hexagon-head bolt
bolt and nut zinc coated and with olive drap colour
grade: 10.9
M12 x 1,5 x 70
made in Germany
2 pieces will be needed for each wishbone

4,96 €inclusive VAT, plus shipping costs

Delivery in 1-3 days

Art.No. 6411

Bushing for steering knuckle

Detail

Compensations washer for the bushing outer wishbone - steering knuckle.

material: plastic-washer
inside diameter: 15 mm
made in EU
for each bushing one piece will be needed

0,95 €inclusive VAT, plus shipping costs

Delivery in 1-3 days

Art.No. 906

Outer wishbone bearing

Detail

Bottom bearing for the connection between steering knuckle and wishbone Trabant front axle. Inclusive bushing for king pin (plastic) and grease nipple.
The plasic bushing have to be crinded after the king pin diameter (an tool like reamer will be helpfully for this work)

material: iron
fit for Trabant 500,600,601
made in EU
for each wheel side will be one piece needed

96,39 €inclusive VAT, plus shipping costs

Delivery in 1-3 days

Art.No. 910

Bushing for king pin

Detail

Plastic bushing for king pin (bottom joint of the front axle). It have to be pressed in from top of the outer wishbone bearing and after that the bushing have to be crinded like the outside diameter of the king pin. (reamer).
The material Miramid is an special plastic with brilliant slipping features.

made in EU
for each wheel side one piece will be needed

9,64 €inclusive VAT, plus shipping costs

Delivery in 1-3 days

Art.No. 911

Grease cap for king pin

Detail

Plastic grease cap to protect the king pin bearing.
Material: plastic with hole for controlling lubrication of king pin bushing

made in Germany
original spare part
two pieces will be needed

3,95 €inclusive VAT, plus shipping costs

Delivery in 1-3 days

Art.No. 6207

King pin ( single part )

Detail

Pin for the bottom side of the Trabant front axle right and left hand.
Delivery as an single part without any mounting parts.
The king pin have to be pressed at the fornt steering knuckle and have to be fixed by an notched tapered pin.
material: steel
survace: 22 H7
best quality with circumferentially greace groove.

35,00 €inclusive VAT, plus shipping costs

Delivery in 1-3 days

Art.No. 912

King pin, repair set

Detail

Complete set, inclusive 1x king-pin, 1x bushing for king pin, 1x seal for king pin, 1x rubber cap for outer wishbone bearing and 1x safety nut for kin pin.
For each axle you need one set.
Fit to Trabant 500, 600, 601

39,36 €inclusive VAT, plus shipping costs

Delivery in 1-3 days

Art.No. 913

Notched tapered pin

Detail

the notched tapered pin will be pressed in the steering knuckle to secure the king pin.
Be careful, do not use the notched tapered pin twice!

8 x 32mm
for each king pin one piece will be needed

1,34 €inclusive VAT, plus shipping costs

Delivery in 1-3 days

Art.No. 916

Sealing ring for king pin

Detail

Rubber sealing ring to protect the lower bearing of the front axle Trabant.
Sealing between axle case and king pin bushing against dust and moisture.
This new produced sealing consist like the orignal one of an V-ring and one pressure O-ring.
All parts are made in Germany and will be the best replacemant for the original one.
scope of delivery:

1x rubber V-ring to protect the bearing
1x O-ring
made in Germany
grease resistant rubber
two pieces will be needed

Made in Germany

3,90 €inclusive VAT, plus shipping costs

Delivery in 1-3 days

Art.No. 914

Washer for king pin 0,2mm

Detail

Spezial washer for adjusting the bearing gap between the Outer wishbone bearing and the king pin.
Empirically different thickness will be needed for an precise adjustment.

material: chadded sheet matal
outside diameter: 20,9 mm
inside diameter: 15 mm
thickness: 0,2 mm
fit to all Trabant 500, 600 and 601

0,24 €inclusive VAT, plus shipping costs

Delivery in 1-3 days

Art.No. 915

Washer for king pin 0,5mm

Detail

Spezial washer for adjusting the bearing gap between the Outer wishbone bearing and the king pin.
Empirically different thickness will be needed for an precise adjustment.

material: chadded sheet matal
outside diameter: 20,9 mm
inside diameter: 15 mm
thickness: 0,5 mm
fit to all Trabant 500, 600 and 601

0,24 €inclusive VAT, plus shipping costs

Delivery in 1-3 days

Art.No. 6523

Washer for king pin 1,0mm

Detail

Spezial washer for adjusting the bearing gap between the Outer wishbone bearing and the king pin.
Empirically different thickness will be needed for an precise adjustment.

material: chadded sheet matal
outside diameter: 21 mm
inside diameter: 14,5 mm
thickness: 1,0 mm
fit to all Trabant 500, 600 and 601

0,88 €inclusive VAT, plus shipping costs

Delivery in 1-3 days

Art.No. 6524

Split pin for king pin

Detail

Splint for the castle nut of the king pin or for the castle nut of the spring yoke.
If new parts like king pin or spring yoke will be used, so you have to drill an hole 3,2mm after you fixed the nut.
Castle nuts are not self-locked, you have to use always an new split pin to secure the bolted connections.

splint: 3,2 x 32
fit to all Trabant 500, 600 und 601
4 pieces will be needed

0,40 €inclusive VAT, plus shipping costs

Delivery in 1-3 days

Art.No. 6526

Castle nut for king pin

Detail

slotted nut for the king pin - Outer wishbone bearing connection.
If new parts like king pin will be used, so you have to drill an hole 3,2mm after you fixed the nut.
Castle nuts are not self-locked, you have to use always an new split pin to secure the bolted connections.

Castle nut: M14 x 1,5mm
tightening torque: 75 Nm
fit to all Trabant 500, 600 und 601
2 pieces will be needed

1,15 €inclusive VAT, plus shipping costs

Delivery in 1-3 days

Art.No. 6525

Castle nut for spring yoke

Detail

slotted nut for the spring yoke - steering knuckle connection.
If new parts like spring yoke will be used, so you have to drill an hole 3,2mm after you fixed the nut.
Castle nuts are not self-locked, you have to use always new split pin to secure the bolted connections.

Castle nut: M12 x 1,5mm
tightening torque: 60 Nm
fit to all Trabant 500, 600 und 601
2 pieces will be needed

1,15 €inclusive VAT, plus shipping costs

Delivery in 1-3 days

Art.No. 6530

Safety nut for king pin Detail Mutter ist selbstsichernd M14x1,5
1,11 €inclusive VAT, plus shipping costs Delivery in 1-3 days Art.No. 917

Counterfort washer for king pin

Detail

ground Counterfort washer will be used to prestress the adjusting the bearing gap between the king pin and the outher wishbone.

material: ginded sheet matal
outside diameter: 34,5 mm
inside diameter: 14,5 mm
thickness: 3,0 mm
fit to all Trabant 500, 600 and 601

2,50 €inclusive VAT, plus shipping costs

Delivery in 1-3 days

Art.No. 6529

Counterfort washer for spring yoke

Detail

ground Counterfort washer will be used to prestress the adjusting the bearing gap between the spring yoke and the steering knuckle.

material: ginded sheet matal
outside diameter: 30 mm
inside diameter: 12,9 mm
thickness: 2,8mm
fit to all Trabant 500, 600 and 601

2,50 €inclusive VAT, plus shipping costs

Delivery in 1-3 days

Art.No. 6528

Miramid washer for spring yoke

Detail

Plastic washer for the Rubber sleeve cushion for leaf spring

material: plastic
outside diameter: 38 mm
inside diameter: 28 mm
thickness: 4 mm
made in EU
two piceswill be needed for each wishbone

1,55 €inclusive VAT, plus shipping costs

Delivery in 1-3 days

Art.No. 921

Spring yoke, complete

Detail

Upper swivel-set for self mounting at the Trabant 601 front axe upper side.
Set consist of these parts:

1x Spring yoke (bearing pin with spring yoke)single part
1x upper bearing bush
1x lower bearing bush
1x sealing ring
1x saling cap
1x hexagon nut
2x plastic washer spring bushing

58,98 €inclusive VAT, plus shipping costs

Delivery in 1-3 days

Art.No. 922

Spring yoke, single part Detail bearing bolt for upper steering bearing with yoke for leaf spring
48,00 €inclusive VAT, plus shipping costs Delivery in 1-3 days Art.No. 923

Safety nut for spring yoke Detail Mutter ist selbstsichernd, M 12x 1,5
0,70 €inclusive VAT, plus shipping costs Delivery in 1-3 days Art.No. 930

Sealing ring for spring yoke, Germany

Detail

Rubber sealing ring to protect the bearing (connection between spring yoke and bushing) against dust and moisture.
This new produced sealing consist like the orignal one of an V-ring and one pressure O-ring.
All parts are made in Germany and will be the best replacemant for the original one.
scope of delivery:

1x rubber V-ring to protect the bearing
1x O-ring
made in Germany
grease resistant rubber
two pieces will be needed

Made in Germany

4,25 €inclusive VAT, plus shipping costs

Delivery in 1-3 days

Art.No. 924

Holder for V-sleeve front axle

Detail

Spring to secure the V-rubber ring at the upper axle joint Trabant 601. This spring clamp fixed the sealing rubber.
Good replacement for the rubber O-ring.

material: steel spring
surface: galvaniced
scope of delivery as an single part
made in Germany
two pieces will be needed

2,26 €inclusive VAT, plus shipping costs

Delivery in 1-3 days

Art.No. 8206

Upper bushing for spring yoke

Detail

Upper bearing for the spring yoke (front axle) of all models of Trabant 601 like Limousine, station wagon, Kuebel and Tramp.
Delivery as single part.
Please note: the complete bearing consist of two parts for each axle 1x upper bushing and 1x lower bushing.
The material of this bushing is Miramid. This is a plastic component with brilliant sliping features.
The bushing have to pressed in the front axle.
additional needed parts, have to be ordered separately:
Lower bushing (part.-no.:926)
Sealing spring yoke (part.-no.:924)

additional needed special tools for assembly:

Reamer 20-H7

5,77 €inclusive VAT, plus shipping costs

Delivery in 1-3 days

Art.No. 925

Lower bushing for spring yoke

Detail

Lower bearing for the spring yoke (front axle) of all models of Trabant 601 like Limousine, station wagon, Kuebel and Tramp.
Delivery as single part.
Please note: the complete bearing consist of two parts for each axle 1x upper bushing and 1x lower bushing.
The material of this bushing is Miramid. This is a plastic component with brilliant sliping features.
The bushing have to pressed in the front axle.
additional needed parts, have to be ordered separately:
Upper bushing (part.-no.:925)
Sealing spring yoke (part.-no.:924)

additional needed special tools for assembly:

Reamer 20-H7

4,20 €inclusive VAT, plus shipping costs

Delivery in 1-3 days

Art.No. 926

Rubber cap for spring yoke / outer wishbone bearing

Detail

Protection cap dor the spring yoke and the lower axle joint.
It saves the screw joint against splash water and dust an it is an lubricant- reservior as well.

material: rubber, black
made in EU
in summery it will be two or four pieces needed

3,90 €inclusive VAT, plus shipping costs

Lieferbar innerhalb von 6-8 Wochen.

Art.No. 927

Washer for spring yoke 0,2mm

Detail

Spezial washer for adjusting the bearing gap between the Steering knuckle and the spring yoke.
Empirically different thickness will be needed for an precise adjustment.

material: chadded sheet matal
outside diameter: 19,0 mm
inside diameter: 12,8 mm
thickness: 0,2 mm
fit to all Trabant 500, 600 and 601

0,24 €inclusive VAT, plus shipping costs

Delivery in 1-3 days

Art.No. 928

Washer for spring yoke 0,5mm

Detail

Spezial washer for adjusting the bearing gap between the Steering knuckle and the spring yoke.
Empirically different thickness will be needed for an precise adjustment.

material: chadded sheet matal
outside diameter: 19,0 mm
inside diameter: 12,8 mm
thickness: 0,5 mm
fit to all Trabant 500, 600 and 601

0,24 €inclusive VAT, plus shipping costs

Delivery in 1-3 days

Art.No. 6527

Washer for spring yoke 1,0mm

Detail

Spezial washer for adjusting the bearing gap between the Steering knuckle and the spring yoke.
Empirically different thickness will be needed for an precise adjustment.

material: chadded sheet matal
outside diameter: 19,0 mm
inside diameter: 13 mm
thickness: 1,0 mm
fit to all Trabant 500, 600 and 601

0,24 €inclusive VAT, plus shipping costs

Delivery in 1-3 days

Art.No. 6787

Split pin for spring yoke

Detail

Splint for spring yoke, it will be fixed thrue the spring yoke into ton convolute eye of the leaf spring.

diameter: 8mm
lenght: 80mm
material: electrogalvanized steel, DIN 94
two pieces will be needed

0,65 €inclusive VAT, plus shipping costs

Delivery in 1-3 days

Art.No. 929

lever grease gun Detail german industry quality pre-installed with reinforced hose and hydraulical connector match grease cartridge: Art.No.: 6311
55,58 €inclusive VAT, plus shipping costs Delivery in 1-3 days Art.No. 6312

lubrication set

Detail

lubrication set consist of:

lever grease gun, Art.No.: 6312
grease cartridge, Art.No.: 6311
adhesive transparent lubricant, Art.No.: 6255

68,68 €inclusive VAT, plus shipping costs

Delivery in 1-3 days

Art.No. 6313

The complete offer in spare parts for the Trabant front axle left and right hand

* All prices inclusive VAT and plus shipping costs.