This site in german: IFA-Fahrzeuge > Framo 
You are here: > IFA-vehicles> Framo

Framo

Category Framo has the following subcategorys:

The product category IFA-vehicles > Framo is spread over 12 sites:

Bolt for starter

Bolt of the Bearing case of the starter engine.
Connection bolt will be mounted at the beraing case threadholes and on the other side it will hold the rear case cover.
Delivery as a single part without nuts an washers.
Can be used for all kind of starters 6V and 12V left- and right turning (without Trabant 1.1, Wartburg 1.3 and Barkas B1000-1)
  • original spare part
  • surface: galvaniced
  • total length: 16.5 cm
  • delivery as an single part
  • for each starter two pieces will needed
original spare part number: 8202.1-000:4/1
2,93 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 7658

Spring for brush starter

Pressure spring for the brushes of the starter engine.
This spring will push the brush at the collector ring from the rotor shaft.
Can be used for all kind of starters 6V and 12V left- and right turning (without Trabant 1.1, Wartburg 1.3 and Barkas B1000-1)
mounting place: brushholder bas plate
  • original spare part
  • delivery as an single part
  • for each starter two pieces will needed
original spare part number: 8202.11-220.6
1,55 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 7629

Battery 6V 84Ah, dry ( not charched )

Batterie for cars with 6V supply voltage. The capacity is 84 Ah. The starting power is 240A.
We just deliver this battery dry and uncharched.
Design fit to historical vehicles.
  • length: 22,5 cm
  • wide: 17,5 cm
  • highness case: 20 cm
  • total highness inclusive pins: 22 cm
  • made in Germany
+7,50 Euro deposit
161,69 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 1225

Battery acid 1,0 liter

Complete pre mixed batterie fluid for using at all starter batterys.
Can be used for 6,12 and 24V voltage system.
  • contens: 1 Liter
  • bottle with child-proof lock
  • please note the instructions at the bottle
3,45 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 7675

Dust cap for ball bearing trunnion bearing rear

Metal cap for protection of the grooved ball bearing at the trunnion bearing A-S rear side agianst dust and dirt.
Fit to direct current dynamos with 6V or 12V.
Useabe for the car types:
Trabant 500,600,601
Wartburg 311,312,313,353
Barkas V901 (Framo)
  • Single spare part
  • original spare part
  • outside diameter: 34mm
  • inside diameter: 15mm
  • one piece will be needed
original spare part number: 8001.4-200:6
1,80 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 7804

Ball bearing for Dynamo ( old type )

Grooved ball bearing to retain the dynamo armature at teh case.
Fit to direct current dynamos with 6V or 12V.
Useabe for the car types:
Trabant 500,600,601
Wartburg 311,312,313,353
Barkas V901 (Framo)
  • Single spare part, delivery without mounting bits
  • high quality made by FAG
  • two pieces will be needed
8,47 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 7796

Dust cap for ball bearing trunnion bearing A-S

Metal cap for protection the grooved ball bearing at the trunnion bearing A-S front side agianst dust and dirt.
Fit to direct current dynamos with 6V or 12V.
Useabe for the car types:
Trabant 500,600,601
Wartburg 311,312,313,353
Barkas V901 (Framo)
  • Single spare part
  • original spare part
  • outside diameter: 29mm
  • inside diameter: 15mm
  • one piece will be needed
original spare part number: 8001.4-200:3
1,80 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 7803

Trunnion bearing A-S dynamo older type

Rear side trunnion bearing complete with pre-installed brushes and pressure springs. Best use for overhauling.
Fit to direct current dynamos with 6V or 12V.
Useabe for the car types:
Trabant 500,600,601
Wartburg 311,312,313,353
Barkas V901 (Framo)
  • Single spare part without mounting equipment and bearing
  • original spare part
  • one piece will be needed
original spare part number: 8001.5-300
39,06 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 7807

Pin bolt for dynamo older type

Special pin for mounting the front and rear trunnion bearing A-S at the dynamo base case.
Fit to direct current dynamos with 6V or 12V.
Useabe for the car types:
Trabant 500,600,601
Wartburg 311,312,313,353
Barkas V901 (Framo)
  • Single spare part
  • original spare part
  • thread: M5
  • length: 170mm
  • two pieces will be needed
original spare part number: 8001.4-000:4
2,25 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 7805
The product category IFA-vehicles > Framo is spread over 12 sites:
123456789101112
Show all products

* All prices inclusive VAT and plus shipping costs.
© 2003 - 2018 LDM-tuning.de
Ersatzteile für Trabant, Wartburg und Barkas