Accessories for the Trabant motor

engine cover on top of the air-cooling housing Trabant two stroke.
mounted with spring clamp (art.no. 1161)

• new original sape part
• one piece will be needed

Spring for coverplate air cooling housing Trabant two stroke motor and cover felt rear door station wagon.

• material: matal, galvanized
• made in EU

Tension spring for mounting the rear ventilation plate at the Trabi engine.
Fit for all two stroke engines at Trabant 500,600 and 601.
Delivery inklusive plasitc protection hose.

• inclusive PVC protection
• surface of the spring: galvaniced
• delivery as single part
• 2 pieces will be needed

Plasitc protection hose for mounting at the tension spring rear ventilation plate at the Trabi engine.
Fit for all two stroke engines at Trabant 500,600 and 601.

• delivery as single part
• material: PVC black
• 2 pieces will be needed

Transmissoinsbelt (without teeth) for the Trabant 500,600 and 601 engine.
The V-belt (wide 10 mm, lenght 1000 mm) fit to all direct current (DC) dynamo (6V and 12V) and to all rotary current (AC) dynamo (12V) for Trabant wit 2-stroke motor.

• one piece will be needed

Transmissoinsbelt (with teeth) for the Trabant 500,600 and 601 engine.
The V-belt (wide 10 mm, lenght 1000 mm) fit to all direct current (DC) dynamo (6V and 12V) and to all rotary current (AC) dynamo (12V) for Trabant wit 2-stroke motor.

• one piece will be needed
• low budget product

Transmissoinsbelt in high quality with teeth for the Trabant 500,600 and 601 engine.
The V-belt (wide 10 mm, lenght 1000 mm) fit to all direct current (DC) dynamo (6V and 12V) and to all rotary current (AC) dynamo (12V) for Trabant wit 2-stroke motor.

• one piece will be needed
• made by Good Year

Retainer for Trabant DC alternator up to vintage october 1983

• material: steel
• scope of delivery without sleeve
• original spare part
• one piece will be needed

Retainer for Trabant AC generator 12V Trabant from vintage october 1983

• material: steel
• scope of delivery without sleeve
• original spare part
• one piece will be needed

Ovel rubber mounting with bolt M8 x 16 mm for bottom side
(connection to under frame) and vulcanized 3 mm sheet steel with two external holes 8,5 mm for fixing upper side (connection to the motor or gearbox.

• Trabant 500 - 600: 1x engine mounting front, 1x gearbox mounting front, 1x gearbox mounting rear
• Trabant 601: 1x engine mounting front, 1x gearbox mounting front
• material: rubber, steel ( with olive drap color)
• width: 67 mm
• length: 86 mm
• highs: 38 mm
• hole distance between 8,5 mm holes: 84 mm

Round rubber mounting with bolt M8 x 16 mm for bottom side
(connection to under frame) and vulcanized 3 mm sheet steel with bolt M8 x 16 mm for fixing upper side (connection to the gearbox).

• Trabant 601: 1x gearbox mounting rear
• material: rubber, steel ( with olive drap color)
• width: 65 mm
• highs: 38 mm

connection hose between pree-silencer and noise silencer for heating systemradiator(down) or between noise silencer for heating systemradiator(top) and heating mixing chamber inside the engine compartment. The rubber hose ferried the heated air to the car. It fit to all Trabant 601 models from november 1976.

• material: rubber
• diameter: 80 mm
• lenght: 120 mm
• two pieces will be needed

Connection hose between heating silencer and heating mixing chamber inside the engine compartment. The rubber hose ferried the hot air to the car. It fit to all Trabant 601 models from april 1973.

• material: rubber
• diameter: 80 mm
• lenght: 300 mm
• one piece will be needed

connection hose between radiator-dummy and heating mixing chamber inside the engine compartment. The rubber hose ferried the fresh air to the car. It fit to all Trabant 601 models from april 1973.

• material: rubber
• diameter: 80 mm
• lenght: 550 mm
• one piece will be needed

Fan fit to all type of Trabant 500, 600 ,601. The air cooling system is driven by the V-belt.
Complete unit, consist of:

• plastic-fan impeller with steel shaft
• aluminium fan case
• v-pulley
• 2x bearing, bushing, clip
• copmete overhauled in Germany
• one piece will be needed

Please select at the frame what kind of fan type do you need !

Overhaul part, please send the clutch and clutch disc in advance to our company

Metal strap for fixing the air cooler at the engine. Fit to all Trabant up to vintage october 1983.
Scope of delivery:

• steel retaining: 680mm x 25 mm x 1mm , galvaniced
• 1x bolt M6, 2x retainer cylindrical, pressure piece
• original spare part
• one piece will be needed

Rubber profile between air cooler and air guiding plate to sonic and vibrations absorber.

• material: rubber, black
• made in Germany
• one piece will be needed

woodruff key 5 x 6,5mm

• all fan shaft Trabant 2-stroke engine, 1 piece
• crankshaft Trabant 601, old version, 2 pieces

Snap ring to fix the V-belt transmisions pulley at the Trabant axial cooling fan shaft.

• made in Germany
• one pieces will be needed

One row roller bearing 6202 for Trabant axial cooling fan.

• made by DKF
• made in Germany
• two pieces will be needed

One row roller bearing 6202 ZZ for Trabant axial cooling fan.

• 2Z or ZZ is a symbol for both side covered
• made by FAG
• made in Germany
• two pieces will be needed

Snap ring to fix the both roller bearings 6202 at the Trabant axial cooling fan.

• made in Germany
• two pieces will be needed