headlights, switches and indicators

LED Headlight as an complete unit.
Best replacement for the H4 or R2 headlights. Brilliant light quality !!!
Fit to Trabant, Trabant 1.1, Baraks B1000, Barkas B1000-1, W50, Multicar, MZ motorbikes.

• scope of delivery: inclusice LEDs
• price per piece!
• electrical power: 12V

Headlamp insert is an complete unit.
Consist of glass lens and mounted light reflector.
The delivery included the bulb socket for the parking lamp.

• scope of delivery: without bulbs
• It will be used one headlamp bulb H4 12V 50/55Wand
• one parking bulb 12V 4W
• best quality, made in EU
• with E-mark

Bilux - Headlamp insert is an complete unit with light reflector.

• scope of delivery: without bulbs
• with E-mark
• It will be additional needed: one headlamp bulb R2 12V 45/40W or
• one headlamp bulb R2 6V 45/40W and
• one parking bulb 6V 4W or
• one parking bulb 12V 4W

Head-lamp-set fit to Trabant 601 and 1,1 without mechanical beam adjusting.
The kit consist of:

• head light housing
• headlight rim
• H4 lense
• sealing for headlight housing
• H4 bulb

Leaver for the headlights for the mechanical beam adjusting.
Fit to Trabant 601 with R2 or H4 headlamp inserts and Trabant 1,1.

• original spare part
• two piece will be needed

Head-lamp-housing without mechanical beam adjusting.
Fit to Trabant 601 and 1,1.

• scope of delivery: inserts
• original spare part

Rubber seal for the connection wire of the front fog lights.
Fit to the round models of the DDR produced fog lamps like at the example picture is shown.

• delivery as an single part
• material: rubber, black

Hexagon screw inclusive spring washer and nut for mounting the fog lights at the car body.
Screw set made of stainless steel.
Fit to the round models of the DDR produced fog lamps like at the example picture is shown.

• Set is made of stainless steel
• 1x screw, 1x nut und 1x spring ring
• two sets will be needed

Hexagon screw inclusive spring washer and nut for mounting the fog lights at the adjustment clamp.
Screw set made of stainless steel.
Fit to the round models of the DDR produced fog lamps like at the example picture is shown.

• Set is made of stainless steel
• 1x screw, 1x nut und 1x spring ring
• two sets will be needed

Retainer for install and adjust the round fog lamps.
New production, made in Germany
Fit to the round models of the DDR produced fog lamps like at the example picture is shown.

• delivery as an single part
• material: plasic, black
• unwrought spare part
• two pieces will be needed

One set of retro round fog lamps.
Best use for oldtimer and youngtimer.

• Delivery as set (2 pieces)
• rear cover: made of plasic,black
• Lieferung inklusive Leuchtmittel und Dichtungen
• one kit will be needed

For use at the Trabant you have to order the set of reatinerfor fog lamp, LDM-part.no.: 8389 separatly.

Retainer for install and adjust the round fog lamps.
New production, made in Germany
Fit to the round models of the DDR produced fog lamps like at the example picture is shown.

• delivery as an single part
• material: plasic, black
• unwrought spare part
• two pieces will be needed

Rectangular fog light as very good replacement for the original lights.
High quality made in Germany.
The sizes agree with the genuine spare parts.
technical details:

• voltage: 12V oder 24V, bulb type: H3
• with E-mark
• dimensions: 160mm x 90mm
• scope of delivery without bulb, inclusive mounting parts
• the case of the lamp is mad of plastic, black

Can be used for Trabant, Wartburg, B1000 und Multicar.

Relais for the electronical switch between low beam and high beam lights.
Reproduction by the original manufactur with best quality.
fit for follow vehicles:

• fit for voltage of 12V
• Trabant 601
• Wartburg 353
• B1000
• for each vehicle, one relais is necessary

relais for low beam / high beam lights
only fit for voltage of 6V
fit for follow vehicles:

• Trabant 601
• Wartburg 353
• B1000
• for each vehicle, one relais is necessary

Plastic indicator cap, angular type fit to Trabant 601 and Trabant 1,1.
High quality like original.

• delivery: single part
• with E-mark
• colour: orange
• front left and right hand mountable
• made in Hungary
• two pieces will be needed

Clear lense for the dircetion indicator Trabant 601.

• material: plastic, colourless
• with E-icon
• made in EU
• needed accessory:
  yellow Bulb 12V / 21W

Front indicator lamp with clear lense for Trabant 601
scope of delivery:

• Glass for direction indicator lamp white
• Seal for indicator insert front
• Seal for indicator lamp front
• Indicator insert complete front
• made in EU
• with E-icon

with clear lense
needed accessory:

• yellow Bulb 12V / 21W

Standard front indicator lamp with orange lense.
This flasher unit fit for Trabant 601 and Trabant 1,1.
with E-icon
needed accessory:
white bulb 12V / 21W

Rubber sealing for the original front indicator glasses type indicator lamp with rounded edges for Trabant 601.
Sealing between indicator frame and base plate.

• material: rubber, black
• delivery as an single
• original spare part

Please note: the picture shows an glas which is not part of the article. It is only for illustrating!

Metal frame for the original front indicator type indicator lamp with rounded edges for Trabant 601.
Please note: dont fit to EU reproductions!
The part is chrome coated but with poor quality.
We sell this indicator frame only as an basic part. The customer have to finish the surface himself.

• material: rubber, black
• delivery as an single
• original spare part

Electronic control unit 12V for flasher lights (direction indicator)
Useable for vehicles without trailer flashers.

Electronic control unit for flasher lights (direction indicator) for 6V systems.
Not for trailer use.

Electronical flasher relais with additional terminal C2 for active light of trailer flasher.
Version with 5 terminals.
New produced spare part.
12V 2+1(6)x 21W + (2)x 0...4W

Electronical flasher relais with additional terminal C2 for active light of trailer flasher.
High quality trade mark.
Version with 5 terminals.
New produced spare part.
12V 2+1(6)x 21W + (2)x 0...4W

flasher relais with additional connector for trailer flasher

• for voltage of 6V
• for correct working of active light for trailer flasher a double-pole flasher switch is necassary (contact name: 49a and 49a´)*

* We can also offer an ancillary relais unit. This unit switchs the second toggle switch of indicator switch (49a´, R´, L´) between the two functions parking light und trailer indicator flasher light.

Please paid attention:

• keep flasher control unit dry
• mount it upright (terminals show downward

functionality:

• The flasher active light flashs in the same steps like direction indicator lamps of the car.
• If one indicator lamp is falling out, the flashing rate of active light doubles.
• The active light for indicator lamp of trailer flashs opponent (active light is on, if indicator lamp of trailer is off).
• If the trailer indicator lamp falls out, the active light remains off.

Rubber sealing for glass of the rear numberblade light. This seal have to be placed under the three lenses inside the lower part of the boot and have to be fixed by the tonques. Can be used for limousine and station wagon.

• colour: red or black
• for each car, 3 pieces will be needed

Clear lense of the rear numberblade lights. This glass have to be placed inside the lower part of the boot and have to be fixed by the tonques. Can be used for limousine and station wagon.

• delivery as single part, without rubber sealings
• original spare part
• for each car, 3 pieces will be needed

Chromed back up light for the mounting on top of the bumber.
The lamp made of high end fabrication and the design fit brilliant to historical cars.

• colour: chromium-plated casing, clear glass
• size: 11 x 5,5 cm
• delivery without bulb
• made in Germany
• with E-icon

Chromed reversing fog light for the mounting on top of the bumber.
The lamp made of high end fabrication and the design fit brilliant to historical cars.

• colour: chromium-plated casing, red glass
• size: 11 x 5,5 cm
• delivery without bulb
• made in Germany
• with E-icon

Chromed reversing registration plate light.
Mounting with two M6 nuts.
The lamp made of high end fabrication and the design fit brilliant to historical cars.

• colour: chromium-plated casing, clear lense
• size: L=82mm x B=29mm x H=27mm
• bolt distance: 45mm
• delivery without bulb
• made in Europe
• mit E-Zeichen

Red glass as spare part for our RETRO fog light

• material: red glass
• made in Germany

Red glass as spare part for our RETRO reverse indication lamp

• material: clear (white) glass
• made in Germany

Standard type of round reflector for rear bumper corner of Trabant 500 and 600 (P50/60)or some other oldtimers.
Only partially fit to back light of Trabant 601 (mounting bolt could be to short).

• Outer diameter: 62,5 mm (2,46")
• Colour: red
• refelector area: 20 cm²
• with base plate made of sheet metal
• centric mounting bolt M5 x 15 mm

Round reflector for rear bumper corner of Trabant 500 and 600 (P50/60) or some other oldtimers, with additional aluminium frame around it.
Only partially fit to back light of Trabant 601 (mounting bolt could be to short).

• Outer diameter: 63,5 mm (2,5")
• Colour: red
• refelector area: 20 cm²
• aluminium ring frame
• with base plate made of sheet metal
• centric mounting bolt M5 x 15 mm

Rear light lense for Trabant 601 like original.

• material: plastic
• colour for stop light and rear light: red
• colour for flasher: orange
• made in EU
• with E-icon

Rear light lense for Trabant 601.

• material: plastic
• colour for stop light and rear light: red
• colour for flasher: whites
• made in EU
• with E-icon

Rear light lense for Trabant 601.

• material: plastic
• colour for stop light, rear light and flasher: white
• made in EU
• with E-icon

Rear light lense for Trabant 601.

• material: plastic
• colour for stop light, rear light and flasher: red
• made in EU
• without E-icon

Rear light lense for Trabant 601.

• material: plastic
• colour for stop light, rear light and flasher: orange
• made in EU
• with E-icon

Bolt for mounting the rear light lenses for Trabant 601.
Can be used at the rear light top an bottom.

• material: stainless steel
• delivery as an single part
• four pieces will be needed

old version of switch for warning flasher
with red round push button
fit to voltage of 12V

• delivery without bulb
• contol bulb:Bulb 12V 2W
• original-spare part no.: 8600.31

6V version of switch for warning flasher. Original spare part.
With red round push button.
Fit to voltage of 6V.
Best use for Old and Youngtimer with 6V electrical system.

• delivery without control bulb
• contol bulb:Bulb 6V 1,2W
• original-spare part no.: 8600.31/1

Cable set for the 6V version of switch for warning flasher.
Fit to voltage of 6V.
Can be used for many Old and Youngtimers.
Best use for Trabant as connecton between flasher unit, fuse box and switch.

• original spare part
• length about:630mm
• one set will be needed

Round rubber for seal the rear light lense to the rear lights base case.

• sponge rubber, black
• length: ca. 65 cm
• two pieces will be needed

Trabant 601 rear light case, single part.

• delivery without mounting parts, bulbs etc.
• new production

New production of the the Trabant 601 rear light.
scope of delivery:

• 1x basic case
• 1x rear light glass
• 1x rubber seal for the rear lense
• 1x bulb holder
• 1x reflector
• without bulbs

Original rubber for sealing the rearlights to the car body. Fit to Trabant 601 and 1,1 (only cero models) universal and limousine.
Original spare part in brilliant quality and size.

• material: rubber
• coulor: black
• original spare part made in Germany
• two pieces will be needed

Rubber seal for the rearlights. fit to Trabant 601 and 1,1 (only cero models) universal and limousine.

• material: rubber
• coulor: black
• made in EU
• two pieces will be needed

The electric switch for the backwards speed lights is mounted direct at the gearbox case. The contact is switched mechanical by the shifting shaft position reverse gear.
At the most cars, the switch have to screwed in the Bushing for switch.

• tap connection: M14 x 1,0 mm
• 2x plate terminal
• delivery without bushing and pin adapter
• made in Europe

Bushing for the reverse gear switch of the Trabant 601 gearbox. This part is necessary if you want to install a switch for the reverse gear. It have to screwed in the gearbox next to the shifting shaft.

• material: matal bushing with innside and outside tap
• galvaniced

Pin adapter for backwards speed lights.

• material: metal

Spare kit with different bulbs fit to voltage of 12V
content:

• 1x R2-lamp 45/40W with base P45t
• 1x spherical lamps 18W white with base Ba15s
• 1x tubular lamp 18W (C21W) with base SV 8,5
• 1x tubular lamp 5W (C5W) with base SV 8,5
• 1x bulb 4W (T4W) with base BA 9s
• 1x bulb for speedometer 0,6W with base BA 7s
• 1x spherical lamps 21W white with base Ba15s
• 1x spherical lamps 5W white with base Ba15s
• 1x Torpedo-fuse 8A
• 1x Torpedo-fuse 16A

Spare kit with different bulbs fit to voltage of 12V
content:

• 1x R2-lamp 45/40W with base P45t
• 2x spherical lamps 21W white with base Ba15s
• 1x tubular lamp 21W (C21W) with base SV 8,5
• 1x tubular lamp 5W (C5W) with base SV 8,5
• 1x bulb 4W (T4W) with base BA 9s
• 1x bulb for speedometer 2W with base BA 7s
• 1x Torpedo-fuse 8A
• 1x Torpedo-fuse 16A

Spare kit with different bulbs fit to voltage of 12V
content:

• 1x H4-lamp 60/55W with base P43t
• 2x spherical lamps 21W white with base Ba15s
• 1x tubular lamp 21W (C21W) with base SV 8,5
• 1x tubular lamp 5W (C5W) with base SV 8,5
• 1x bulb 4W (T4W) with base BA 9s
• 1x bulb for speedometer 2W with base BA 7s
• 1x Torpedo-fuse 8A
• 1x Torpedo-fuse 16A