This site in german: Wartburg 1.3 > Ersatzteile > Getriebe 
You are here: > Wartburg 1.3> Spare parts> gear box

Spare parts and accessories for the Wartburg 1,3 gear box

The product category Wartburg 1.3 > Spare parts > gear box is spread over 4 sites:

Disengaging shaft ( for clutch ) W1,3

Lever shaft for the clutch of the Wartburg 1.3 engine.
Mounting place: gearbox clutch void.
Spare part is complete with lever for the clutch cable and two arms for the clutch disenger.
  • steel contruction
  • one piece will be needed
  • made in Europe
99,50 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 7429

Bushing for Disengaging shaft ( for clutch ) T1,1

Guiding bushing for the lever shaft for the clutch of the Trabant 1.1 and Wartburg 1,3.
Mounting place: gearbox clutch void.
  • material: plastic
  • one piece will be needed
  • made in Europe
12,38 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 7859

Band clamp, short

Rebound strap for mounting of sleeve rubbers of universal shafts
long band clamp (for example for mounting of sleeve rubber on shaft joint), for diameter from 25mm up to 50mm
application:
  • the band clamp have to bent around the sleeve rubber by hand, so that it clinging to the sleeve rubber in best way
  • fixing this position by hooking into
  • spanning the band clamp with a pincers
  • ready
3,03 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 6536

Band clamp , long

Rebound strap for mounting of sleeve rubbers of universal shafts
long band clamp (for example for mounting of sleeve rubber on shaft joint), for diameter from 40mm up to 110mm
application:
  • the band clamp have to bent around the sleeve rubber by hand, so that it clinging to the sleeve rubber in best way
  • fixing this position by hooking into
  • spanning the band clamp with a pincers
  • ready
3,81 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 6408

Rebound strap 4,6 X 360 mm

Strap for rubber sleeves.
  • material: stainless steel
  • made in Germany
  • 4 pieces will be needed
2,48 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 655

Band clamp set for sleeve rubber of universal shaft

Rebound strap set for mounting of sleeve rubbers of universal shafts
consist of:
  • long band clamp (for example for mounting of sleeve rubber on shaft joint), for diameter from 40mm up to 110mm
  • short band clamp to seal sleeve rubber on universal shaft, for diameter from 25mm up to 50mm

application:
  • the band clamp have to bent around the sleeve rubber by hand, so that it clinging to the sleeve rubber in best way
  • fixing this position by hooking into
  • spanning the band clamp with a pincers
  • ready
5,20 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 6394

Pin for wheel nut Wartburg

Locking pin for the castle nut to lock the wheel hub - wheel bearing - connection.
The pin fit to the front axle drive shaft and to the rear axle kingpin.
  • fit to Wartburg 353 and Wartburg 1.3
  • delivery as an single
  • four pieces will be needed
0,25 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 8026

Centering washer dirve shaft

Special washer for centering the wheel hub and the drive shaft (wheel side).
Mounting place between castle nut and the wheel hub.
The washer fit to the front axle drive shaft.
  • fit to Wartburg 353 and Wartburg 1.3
  • delivery as an single part
  • material: steel, galvaniced
  • two pieces will be needed
original spare part number: 134 29 11 006 075 701
3,82 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 8174

Wheel nut Wartburg

Castle nut for mounting the wheel hub - wheel bearing - connection.
The nut fit to the front axle drive shaft and to the rear axle kingpin.
  • fit to Wartburg 353 and Wartburg 1.3
  • delivery as an single part without pin
  • four pieces will be needed
3,84 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 8025

Sleeve rubber W1,3 (outer universal shaft side)

Rubber boot for the outher drive shaft joint of the Wartburg 1.3
It is always one piece assembled form the outer side of the joint and one piece from the inner side.
This oel (Art.-Nr.:6619) have to be used for the lubication of the outer joint.
  • material: rubber, black
  • made in EU
  • delivery as an single part without mounting pats

Additional needed mounting parts (not scope of delivery of the rubber boot):
2x Band clamp, long (part.-No.:6408)
2x Clamp (part.-No.:7608)
additional needed tools for dismounting and mounting (not part of this offer):
1x Seeger ring pliers, external retaining rings 19-60mm (LDM-part.-Nr.:8322)
12,54 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 8414

Sleeve rubber set outer universal shaft side W1,3

One kit of rubber boots and assambly parts for the outher drive shaft joint of the Wartburg 1.3
It is always one piece assembled form the outer side of the joint and one piece from the inner side.
Scope of delivery:
2x Rubber boot wheel side (LDM-Art.-Nr.:8414)
1x oel for the lubication of the outer joint (LDM-Art.-Nr.:6620)
2x Band clamp, long (LDM-part.-No.:6408)
2x Clamp (LDM-part.-No.:6780)
  • one kit will be needed for each drive shaft (total: 2 set)

additional needed tools for dismounting and mounting (not part of this offer):
1x Seeger ring pliers, external retaining rings 19-60mm (LDM-part.-Nr.:8322)
36,86 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 8415

Sealing ring for plug screw

sealing ring for plug screw gearbox-oel
fit for gear boxes of follow vehicles:
  • material: aluminium
  • size: 22x27x1,5
  • one piece will be needed
  • Trabant 601
  • Trabant 1.1
  • Wartburg 353
  • Wartburg 1.3
  • B1000
  • and for most other vehicles
1,20 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 6357
The product category Wartburg 1.3 > Spare parts > gear box is spread over 4 sites:
1234
Show all products

* All prices inclusive VAT and plus shipping costs.
© 2003 - 2023 LDM-tuning.de
Ersatzteile für Trabant, Wartburg und Barkas
  Werbung: Saurier