Spare parts and accessories for the Wartburg 1,3 gear box

The complete offer in Spare parts and accessories for the Wartburg 1,3 gear box

Sleeve rubber ( inner side ) big joint

Sleeve rubber for universal shaft (gearbox side)
fit to Trabant 1.1, Wartburg 1.3 and Skoda Favorit (all 4-stroke)
size:

inner diameter gearboxside: 82 mm
inner diameter universalschaft side: 19 mm
length 92 mm
for each universal shaft one piece will be needed

14,90 €inclusive VAT, plus shipping costs

Delivery in 1-3 days

Art.No. 662

Sleeve rubber-Set ( inner side ) small joint

Detail

sleeve rubber for universal shaft (gearbox side.
Used for the small joint, diameter: 70mm.
fit to Trabant 1.1, Wartburg 1.3 and Skoda Favorit (all 4-stroke)
size:

set consist of: 1x special joint grease, 2x straps, 1x rubber sleeve
made in Germany
inner diameter gearboxside: 69 mm
inner diameter universalschaft side: 19 mm
length 95 mm
for each universal shaft one piece will be needed

20,58 €inclusive VAT, plus shipping costs

Delivery in 1-3 days

Art.No. 7243

Snap ring sleeve rubber final drive

Detail

Circlip for mounting at the Wartburg 353 and Wartburg 1,3 drive shaft boot.
Can be used at the inner sleeve of the outside joint.

Two piece will be needed for each car

Needed plier for dismounting and mounting (not part of this offer):
1x Seeger ring pliers, external retaining rings 19-60mm (LDM-part.-Nr.:8322)

2,26 €inclusive VAT, plus shipping costs

Delivery in 1-3 days

Art.No. 7680

1+1

Final drive set W1,3

Detail

Drive shaft kit for mounting at the Wartburg 1.3 (four stroke engine)
Kit consists of:
1x drive shaft right hand (long)
1x drive shaft left hand (short)
This type of drive shafts is special modificated. The outer joints are replaced into constant velocity drives.

New production, made in EU
fit only to Wartburg 1,3 all models like Limousine, Tourist and Trans

fit only to Wartburg 1,3

680,13 €inclusive VAT, plus shipping costs

Delivery in 1-3 days

Art.No. 7791

Boot for inner joint (final drive set W1,3)

Detail

Please note: only fit for LDM-part.No.7791

23,58 €inclusive VAT, plus shipping costs

Delivery in 1-3 days

Art.No. 8218

Boot for outher joint ( Final drive set W1,3 )

Detail

Please note: This boot kit fit only for our offered Drive shaft set (part.-no.:7791) Wartburg 1,3.

Please note: only fit for LDM-part.No.7791

34,91 €inclusive VAT, plus shipping costs

Delivery in 1-3 days

Art.No. 3146

Gear oil, 1,5l

Detail

One set of hypoid gear oil for the Trabant 1,1 and Wartburg 1,3 gearbox.
The total filling amount is 1,2 liter.

set consists of 1x packet SAE 80W 1 liter and 1x packet SAE 80W 0,5 liter
quality made by Liqui Moly
Hypoid gear oil
mineral-based oil
one set will be needed

price: 14,24 Euro / Liter

21,36 €inclusive VAT, plus shipping costs

Delivery in 1-3 days

Art.No. 8271

Classic Gear oil, 5l

Detail

One set of hypoid gear oil for the Trabant 1,1 and Wartburg 1,3 gearbox.
The total filling amount is 1,2 liter.

consis 5 liter
made in Germany
mildly alloyed gear oil
mineral-based oil

price: 16,12 Euro / Liter

80,58 €inclusive VAT, plus shipping costs

Lieferbar innerhalb von 6-8 Wochen.

Art.No. 8272

Oil seal gearbox casing - universal shaft right

Detail

Radial sealing with special oil return twist.
Please note: this seal can be only installed at the right hand (codriver side)
Made for the Trabant 1.1 and Wartburg 1,3 gearbox.
Mounting place: differential gear - right hand universal shaft

seal with readvancing twist
type with additional dust lip
inside diameter: 40mm
outside diameter: 52mm
gauge: 7mm
right hand

10,90 €inclusive VAT, plus shipping costs

Delivery in 1-3 days

Art.No. 3152

Oil seal gearbox casing - universal shaft left

Detail

Radial sealing with special oil return twist.
Please note: this seal can be only installed at the left hand (driver side)
Made for the Trabant 1.1 and Wartburg 1,3 gearbox.
Mounting place: differential gear - left hand universal shaft

seal with readvancing twist
type with additional dust lip
inside diameter: 40mm
outside diameter: 52mm
gauge: 7mm
left hand

10,90 €inclusive VAT, plus shipping costs

Delivery in 1-3 days

Art.No. 3153

Radial sealing D20 x 40 x 7

Detail

Shaft sealing in normal version without dust lip for cluthch-shaft gearbox side (gearbox input shaft).

fit to the vehicles Trabant 1.1, Wartburg 1.3 and B1000
without dust lip
made in Germany
one piece will be needed

6,31 €inclusive VAT, plus shipping costs

Delivery in 1-3 days

Art.No. 6069

Radial sealing D20 x 40 x 7 SL

Detail

Radial sealing with additional dust lip for clutch-shaft gearbox side for

Fit to:

Trabant 1.1
Wartburg 1.3
B1000 (2-stroke engine with new type of gear box) and B1000-1 (4-stroke)
made in Germany
one piece needed

6,72 €inclusive VAT, plus shipping costs

Delivery in 1-3 days

Art.No. 6388

Flexible shaft for speedometer

Detail

Flexible shaft for speedometer fit to all Wartburg 353 and Wartburg 1,3.

total lenght of the shaft: 1170 mm
both ends are with tetrahedral tappet: 2,6 x 2,6 mm
connection screw joint: aluminium-nut
one piece will be needed

16,63 €inclusive VAT, plus shipping costs

Delivery in 1-3 days

Art.No. 3500

Sleeve for gear shifting shaft

Detail

Protection collar for the gear shifting shaft of the Wartburg 1.3 (4-stroke)

original spare part
one piece will be needed

35,09 €inclusive VAT, plus shipping costs

temporary not available

Art.No. 6933

sleeve for cluch cable

Detail

sleeve for clutch cable of Wartburg 353 (2-stroke) and Wartburg 1.3 (4-stroke)

length: 90mm
lenght (short): ca. 55mm
inner diameter big: 12mm
inner diameter small: ca. 6mm

Subject to availability (no regular range)!

8,80 €inclusive VAT, plus shipping costs

Lieferbar innerhalb von 6-8 Wochen.

Art.No. 6370

Socket joint set (inner joint) for transmission shaft, complete (T1.1/W1.3)

Detail

complete set of socket joint for transmission shaft of Trabant 1.1 or Wartburg 1.3
spare part made made in EU.
set consist of:

Inner joint (sliding socket with external teeth stub shaft)
1x shaft spider
fitted rubber sleeve
set of band clamps (1x long and 1x short)
1x tube of special grease for transmission shafts

92,34 €inclusive VAT, plus shipping costs

Delivery in 1-3 days

Art.No. 6795

Shaft seal - universal shaft

Detail

Radial oel seal for wheel side he drive Wartburg 353 gearbox.
The sealing will be mounted at the inner side of the wheel bearing housing / steering knuckle (driveshaft side).
Fit the the left and right hand of the steering knuckle.

size: 45 x 60 x 7
material: NBR (Nitril-rubber)
with additional dust lip
made in Germany
two pieces will be needed (one for each drive shaft)

8,77 €inclusive VAT, plus shipping costs

Delivery in 1-3 days

Art.No. 7002

Bearing bush in gear change rod

Detail

Plastic bearing bush fit to gearbox side end of gear change rod.
The plastic bushing for gear change rod will be mounted at the ball stud for gear selector shaft LDM-part no.: 8214.

one piece will be needed for one gear change rod
fit to Trabant 1,1 and Wartburg 1,3
Part-No.: 03 16129 001

14,88 €inclusive VAT, plus shipping costs

Delivery in 1-3 days

Art.No. 7039

Ball stud for gear selector shaft

Detail

Ball stud as single part.
Fit to all gear selectors at the Trabant 1.1 and Wartburg 1.3
This ball stud will be mounted at the plastic bushing for gear change rod LDM-part no.: 7039.

one piece will be needed for one gear change rod
delivery inclusive mounting nut
fit to Trabant 1,1 and Wartburg 1,3
Part-No.: 99 00244 143

5,56 €inclusive VAT, plus shipping costs

Delivery in 1-3 days

Art.No. 8214

Ball holder for preselective rod

Detail

Ball holder for both ends of preselective rod (connection between gearbox and gear change rod)

two pieces will be needed for one preselective bar
fit to Trabant1,1 and Wartburg 1,3
Part-No. (Wartburg): 53 01304 405

4,60 €inclusive VAT, plus shipping costs

Delivery in 1-3 days

Art.No. 7038

Ball bearing for bell crank

Detail

Ball stud as single part for the bell crank 1x top and 1x bottom side.
Can be used for the original plastic ball holder (LDM-part no.:7038)
Fit to all gear selectors at the Trabant 1.1 and Wartburg 1.3
This bearings will be mounted at the gear change rod LDM-part no.: 8216.

two piece will be needed
delivery inclusive mounting nut
fit to Trabant 1,1 and Wartburg 1,3
Part-No.:

5,95 €inclusive VAT, plus shipping costs

Delivery in 1-3 days

Art.No. 8231

Ball bearing for bell crank

Detail

Bearing for the bell crank consist of ball stud and ball holder.
Reclacement made of metal for the original plastic ball holder (LDM-part no.:7038)
Fit to all gear selectors at the Trabant 1.1 and Wartburg 1.3
This bearings will be mounted at the gear change rod LDM-part no.: 8216.

two piece will be needed
delivery inclusive mounting nut
fit to Trabant 1,1 and Wartburg 1,3
Part-No.:

5,83 €inclusive VAT, plus shipping costs

Delivery in 1-3 days

Art.No. 8215

Ball bearing for bell crank

Detail

one piece will be needed
scope of delivery inclusive 2x joint
delivery inclusive 2x mounting nut
fit to Trabant 1,1 and Wartburg 1,3
Part-No.:

14,90 €inclusive VAT, plus shipping costs

Delivery in 1-3 days

Art.No. 8216

Front wall collar

Detail

Rubber sleeve to seal the hole of gear change rod to the bulkhead to the engine compartment.
Fit to all types of Trabant 1.1 and Wartburg 1.3

Material: rubber, black
reproducted part, EU

12,78 €inclusive VAT, plus shipping costs

Delivery in 1-3 days

Art.No. 697

shaft spider for transmission shaft, T1,1 / W1,3 complete

Detail

Complete spare part shaft spider for the Trabant 1.1 and Wartburg 1.3 drive shaft.
Right and left side mountable.
Teeth at the drive shaft: 22
Please note: This three finger spider can be only used for the huge type of drive shaft joint. Outside diameter: 80mm

diameter spiderring: 30mm
diameter spider: about 70mm
For each universal shaft one piece will be needed
made in Europe

52,43 €inclusive VAT, plus shipping costs

Delivery in 1-3 days

Art.No. 669

Disengaging shaft ( for clutch ) W1,3

Detail

Lever shaft for the clutch of the Wartburg 1.3 engine.
Mounting place: gearbox clutch void.
Spare part is complete with lever for the clutch cable and two arms for the clutch disenger.

steel contruction
one piece will be needed
made in Europe

99,50 €inclusive VAT, plus shipping costs

Delivery in 1-3 days

Art.No. 7429

Bushing for Disengaging shaft ( for clutch ) T1,1

Detail

Guiding bushing for the lever shaft for the clutch of the Trabant 1.1 and Wartburg 1,3.
Mounting place: gearbox clutch void.

material: plastic
one piece will be needed
made in Europe

12,38 €inclusive VAT, plus shipping costs

Delivery in 1-3 days

Art.No. 7859

Band clamp, short

Detail

Rebound strap for mounting of sleeve rubbers of universal shafts
long band clamp (for example for mounting of sleeve rubber on shaft joint), for diameter from 25mm up to 50mm
application:

the band clamp have to bent around the sleeve rubber by hand, so that it clinging to the sleeve rubber in best way
fixing this position by hooking into
spanning the band clamp with a pincers
ready

3,03 €inclusive VAT, plus shipping costs

Delivery in 1-3 days

Art.No. 6536

Band clamp , long

Detail

Rebound strap for mounting of sleeve rubbers of universal shafts
long band clamp (for example for mounting of sleeve rubber on shaft joint), for diameter from 40mm up to 110mm
application:

the band clamp have to bent around the sleeve rubber by hand, so that it clinging to the sleeve rubber in best way
fixing this position by hooking into
spanning the band clamp with a pincers
ready

3,81 €inclusive VAT, plus shipping costs

Delivery in 1-3 days

Art.No. 6408

Rebound strap 4,6 X 360 mm

Detail

Strap for rubber sleeves.

material: stainless steel
made in Germany
4 pieces will be needed

2,48 €inclusive VAT, plus shipping costs

Delivery in 1-3 days

Art.No. 655

Band clamp set for sleeve rubber of universal shaft

Detail

Rebound strap set for mounting of sleeve rubbers of universal shafts
consist of:

long band clamp (for example for mounting of sleeve rubber on shaft joint), for diameter from 40mm up to 110mm
short band clamp to seal sleeve rubber on universal shaft, for diameter from 25mm up to 50mm

application:

the band clamp have to bent around the sleeve rubber by hand, so that it clinging to the sleeve rubber in best way
fixing this position by hooking into
spanning the band clamp with a pincers
ready

5,20 €inclusive VAT, plus shipping costs

Delivery in 1-3 days

Art.No. 6394

Pin for wheel nut Wartburg

Detail

Locking pin for the castle nut to lock the wheel hub - wheel bearing - connection.
The pin fit to the front axle drive shaft and to the rear axle kingpin.

fit to Wartburg 353 and Wartburg 1.3
delivery as an single
four pieces will be needed

0,25 €inclusive VAT, plus shipping costs

Delivery in 1-3 days

Art.No. 8026

Centering washer dirve shaft

Detail

Special washer for centering the wheel hub and the drive shaft (wheel side).
Mounting place between castle nut and the wheel hub.
The washer fit to the front axle drive shaft.

fit to Wartburg 353 and Wartburg 1.3
delivery as an single part
material: steel, galvaniced
two pieces will be needed

original spare part number: 134 29 11 006 075 701

3,82 €inclusive VAT, plus shipping costs

Delivery in 1-3 days

Art.No. 8174

Wheel nut Wartburg

Detail

Castle nut for mounting the wheel hub - wheel bearing - connection.
The nut fit to the front axle drive shaft and to the rear axle kingpin.

fit to Wartburg 353 and Wartburg 1.3
delivery as an single part without pin
four pieces will be needed

3,84 €inclusive VAT, plus shipping costs

Delivery in 1-3 days

Art.No. 8025

Sleeve rubber W1,3 (outer universal shaft side)

Detail

Rubber boot for the outher drive shaft joint of the Wartburg 1.3
It is always one piece assembled form the outer side of the joint and one piece from the inner side.
This oel (Art.-Nr.:6619) have to be used for the lubication of the outer joint.