Exhaust Trabant 601

Exhaust manifold, complete for Trabant 601 two stroke engine, with cover for heating system
from vinatage: november 1976

• original-IFA-spare part
• cover: galvanized
• one piece will be needed

Exhaust manifold as an second hand part for Trabant 601 two stroke engine
The manifold will be cleaned up by washing and checked for cracks.
We offer only original mainfolds.

Exhaust manifold as an second hand part for Trabant 601 two stroke engine
The manifold will be cleaned up by washing and checked for cracks.
We offer only original mainfolds.

Rear muffler with pipe for Trabant 601.
New Reproduction in hight quality.
Exhaust will be deliverd without any mounting parts.

• Muffler with pipe for Trabant 601
• made in EU
• one piece will be needed

additional needed mounting parts (not scope of delivery of the echaust):
3x Exhaust retainer,angular (Art.-Nr.:47)
or
3x Exhaust retainer,angular LDM (Art.-Nr.:7099)
and
1x Pipe clamp D= 38mm (Art.-Nr.:48)
or
1x Pipe clamp D= 38,5mm (Art.-Nr.:6385)

cheap after muffler
the quality is not the best (the postions of the mounting brackets are not correct)

Muffler with pipe for Trabant 601

Retainer round, for Trabant exhaust system 2-stroke engine

• material: rubber with vulcanized 90 degrees twisted metal plate
• length complete: 74 mm
• length rubber body: 24 mm
• diameter rubber body: 25mm (top-down) / 13 mm (middle)
• Made in EU
• one piece will be needed

Retainer round, for Trabant exhaust system 2-stroke engine

Retainer with fair quality of rubber insert and surface of sheet metall.

• material: rubber with vulcanized 90 degrees twisted sheet metal plates
• length complete: 82 mm
• length rubber body: 28 mm
• diameter rubber body: 34mm (top and down) / 16 mm (middle)
• Made in EU
• one piece will be needed

Clamp for exhaust system Trabant 601
One piece will ne needed for connection between pre selincer and connection pipe.
One piece will ne needed for connection between connection pipe and after muffler.

• material: galvaniced steel
• for pipe diameter: 38 mm
• two pieces will be needed

exhaust pipe clamp flat steel

• pipe clamp made of 2,5 mm steel strip
• for pipe diameter: 38 mm
• zinc-coated
• widht: 25mm
• max. tightening torque: 20 Nm

exhaust pipe coupling clamp.
Brilliant for connecting pipe end with the same diameter.
Consist of 1x sheet metal and 2x pipe clamp.

• material: stainless steel-zinc-coated metal
• for pipe diameter: 36-38 mm
• length: 90 mm
• made in Germany
• max. tightening torque: 20 Nm

Universal brass cover for exhaust, chromium-plate 44 x 130 mm
fit for all Trabant

Universal cover for exhaust, chromium-plate 48 x 120 mm,
round-convoluted-transversal cuted
fit to pipe diameter 24 - 48 mm

Universal brass cover for exhaust, chromium-plate 70 x 57 x 145 mm,
angular-transversal cuted
fit to pipe diameter 30 - 50 mm
for all Trabant

connection hose between radiator-dummy and heating mixing chamber inside the engine compartment. The rubber hose ferried the fresh air to the car. It fit to all Trabant 601 models from april 1973.

• material: rubber
• diameter: 80 mm
• lenght: 550 mm
• one piece will be needed

Connection hose between heating silencer and heating mixing chamber inside the engine compartment. The rubber hose ferried the hot air to the car. It fit to all Trabant 601 models from april 1973.

• material: rubber
• diameter: 80 mm
• lenght: 300 mm
• one piece will be needed

connection hose between pree-silencer and noise silencer for heating systemradiator(down) or between noise silencer for heating systemradiator(top) and heating mixing chamber inside the engine compartment. The rubber hose ferried the heated air to the car. It fit to all Trabant 601 models from november 1976.

• material: rubber
• diameter: 80 mm
• lenght: 120 mm
• two pieces will be needed