This site in german: Trabant 601 > Ersatzteile > Motor 
You are here: > Trabant 601> Spare parts> Engine

spare parts for the motor Trabant 601

Category spare parts for the motor Trabant 601 has the following subcategorys:

The complete offer in spare parts for the motor Trabant 601

Engine, complete

+ 400 Euro deposit
1450,11 €inclusive VAT, plus shipping costs
Lieferbar innerhalb von 6-8 Wochen.

Art.No. 601

Engine, complete, sport crank

+ 400 Euro deposit
1556,15 €inclusive VAT, plus shipping costs
Lieferbar innerhalb von 6-8 Wochen.

Art.No. 7281
Crank shafts for serial-, tuning,- and hycomat engines

Crankshaft, complete overhauled

crankshaft for all Trabant 601 engine two stroke 26hp.
The crankshaft is complete overhauled. Inclusive all bearings and needle bearings for piston pins.
  • one piece will be needed

one piece will be needed
pledge for old crank shaft +150,00 Euro!
if old part will be sended back the money will be transfered back
for more informations, see details
+ 150 Euro deposit
637,31 €inclusive VAT, plus shipping costs
Lieferbar innerhalb von 6-8 Wochen.

Art.No. 605

Tuning crankshaft Trabant

Crankshaft with special conrod bearings for Trabant tuning engines.
The crankshaft is complete overhauled. Inclusive all bearings and needle bearings for piston pins.
  • one piece will be needed

one piece will be needed
pledge for old crank shaft +150,00 Euro!
if old part will be sended back the money will be transfered back
for more informations, see details
+ 150 Euro desposit
698,20 €inclusive VAT, plus shipping costs
Lieferbar innerhalb von 6-8 Wochen.

Art.No. 6548

Crankshaft, complete overhauled, hycomat

crankshaft for all Trabant 601 with hycomat gearbox, engine two stroke 26hp.
The crankshaft is complete overhauled. Inclusive all bearings and needle bearings for piston pins.
  • one piece will be needed

one piece will be needed
pledge for old crank shaft +150,00 Euro!
if old part will be sended back the money will be transfered back
for more informations, see details
+ 150 Euro desposit
698,20 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 6470

Spare bearings for crankshaft of Trabant engine

Fit to all crankshafts of last production series, made as of 1984
As of 1984 new types of bearings with special dimensions were make to increase the load rating and a higher marginal utility. In the same year the piston ring sealing was implemented.

roller bearing, side of belt pulley

Cylindrical roller bearing with special dimensions.
Fit to outer stub shaft of crankshaft of Trabant 601 engine (side of belt pulley).
Made in GDR
19,96 €inclusive VAT, plus shipping costs
0temporary not available
temporary not available

Art.No. 6102

Ball bearing set, side of flywheel

Set to change the bearing with special dimensions into the bearing 6009N with adapter ring.
Fit to outer stub shaft of crankshaft of Trabant 601 engine (side of flywheel).
Diameter of stub shaft: 40mm
  • scope of delivery: 1x adapterring, 1x ball bearing
  • all parts in Germany
  • one set will be needed
49,00 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 6103

Ball bearing -middle

Special bearing for the Trabant crankshaft.
Fit to the middle shafts of crankshaft cylinder 1 and 2 (bearing position 2 and bearing position 3)
Fit to all Trabant two stroke enines.
Made by the original manufacture.
  • scope of delivery without pin
  • all parts in Germany
  • two pieces will be needed
24,95 €inclusive VAT, plus shipping costs
Lieferbar innerhalb von 6-8 Wochen.

Art.No. 7267

Pressure springs for rotary valve

Special spring for Trabant rotary valve. Fit to all Trabant 2-stroke engine.
  • length: 21 mm
  • diameter: 6 mm
  • made in Germany
  • 2 pieces will be needed for each rotary valve
Special offer normaly 0,98 € now 0,65 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 6186

Rotary valve - set, complete with pressure springs

Complete set rotary valve for Trabant twostroke crankshaft.
  • material: metal
  • made in EU
  • Set include 2x rotary valve and 4x springs
14,81 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 607

Gasket kit Trabant engine

Set to seal the Trabi engine.
Good use after repairing or total overhauling of the engine block.
Scope of delivery:
  • Two pieces of exhaust manifold gaskets
  • Two pieces of cylinder head packing
  • Two pieces of Cylinder base packing
  • Two pieces of gasket for carburettor flange
  • One piece of seal for bearing cover crank shaft
9,80 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 7501

Waved washer for crank shaft

The waved washer fit to Trabant 500,600 and 601 cranks flywheel side.
It can be mounted to all types of disc flywheels with piston ring - or shaft sealings.
  • material: spring metal
  • genuine spare part
  • one piece will be needed
6,34 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 7114

V-spring for crank shaft

Cup spring fit to Trabant 500,600 and 601 cranks flywheel side.
It can be mounted to all types of disc flywheels with piston ring - or shaft sealings.
  • material: spring metal
  • genuine spare part
  • two piece will be needed
5,70 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 7118

Seal for bearing cover crank shaft, old version

Paper sealing for the bearing cover with radial shaft sealing.
Can be used for Trabant 500,600 and 601 cranks flywheel side.
It can be mounted to all types of disc flywheels with shaft sealings.
  • material: chadded sealing paper
  • inside diameter:75mm
  • outside diameter:84mm
  • thickness:0,8 mm
  • genuine spare part
  • one piece will be needed
2,25 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 7553

Seal for bearing cover crank shaft

Paper sealing fit to Trabant 500,600 and 601 cranks flywheel side.
It can be mounted to all types of disc flywheels with piston ring sealings.
  • material: chadded sealing paper
  • inside diameter:75mm
  • outside diameter:84mm
  • thickness:0,8 mm
  • genuine spare part
  • one piece will be needed
2,25 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 7119

Radial seal for crankshaft ( clutch-side ) 55x70x8S1 with dust lip

Crankshaft radial seal motor clutch-side
  • size: D 55x 70 x 8 S1
  • with additionally dust lip
  • made in Germany
  • one piece will be needed
7,19 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 6054

Radial seal for crankshaft ( clutch-side ) 55x70x8S1

Crankshaft radial seal motor clutch-side
  • size: D 55x 70 x 8 S1
  • reporduction
  • one piece will be needed
6,48 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 608

Radial seal for crankshaft ( V-belt pulley side ) 42x67x10S2

Crankshaft radial seal motor v-belt pulley side
  • size: D 42 x 67 x 10 S2
  • new production, good quality
  • one piece will be needed
13,27 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 609

Comprssion ring for crankshaft ( V-belt pulley side )

Crankshaft compression ring seal motor v-belt pulley side
  • original spare part
  • two pieces will be needed
12,21 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 7333

Needle bearing for connection rod / piston pin

  • size: 24 x 26 x 2
  • count of needles: 36
  • one piece will be needed for each connection rod
10,81 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 610

Piston pin 20 x 56

piston pin for Trabant 601 from vintage: dezember 1984
  • lenght: 56 mm
  • diameter: 20mm
  • two pieces will be needed
10,89 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 625

Wire snap ring

Wire snap ring for piston pin. You need two pieces for one piston.
Fit to all Trabant 601, Wartburg 353 and B1000 pistons
3,76 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 626

Cylinder head nut comlete with washer

Cylinder head nut fit to all Trabant 500,600 and 601 with two stroke engine.
  • strength class: 10.9
  • scope of delivery complete with washer
  • 4 pieces will be needed for each cylinder

The tighten bolt order and the torque you can find in details!
0,55 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 6480

Cylinder head packing (head gasket)

Cylinder head packing for Trabant 601.
  • material: aluminium
  • one piece will be needed for each cylinder

The tighten bolt order and the torque you can find in details!
2,55 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 630

Cylinder base nut with washer

Cylinder base nut fit to all Trabant 500,600 and 601 with two stroke engine.
  • strength class: 10.9
  • scope of delivery complete with washer
  • 4 pieces will be needed for each cylinder (total 8 pieces)

The tighten bolt order and the torque you can find in details!
0,55 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 6481

Cylinder base packing

Gasket for cylinder base of the Trabant engine. Can be used for all types of two stroke motors of Trabant 500,600 and 601.
  • material: embossed-sealing paper
  • one piece will be needed for each cylinder

The tighten bolt order and the torque you can find in details!
3,10 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 631

Ring gear for starter ( 8 mm )

ring gear for engine starter Trabant 601 up to march 1972. It will be fixed at the fleywheel by shrinking.
  • width: 8mm
  • outside diameter: ca.250 mm
  • inside diameter: ca.228 mm
  • tooth ratio: 100
  • one piece will be needed
68,90 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 7795

Ring gear for starter ( 6 mm )

ring gear for engine starter Trabant 601 from march 1972. It will be fixed at the fleywheel by shrinking.
  • width: 6mm
  • outside diameter: ca.250 mm
  • inside diameter: ca.228 mm
  • tooth ratio: 100
  • one piece will be needed
23,42 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 685

hexagon nut for crankshaft (side of V-belt pulley)

hexagon nut for mounting the V-belt pulley on crankshaft
the lock plate (Art.No. 6128) have to be changed after every disassembly.
  • turning moment: 54 Nm
  • original spare part
  • galvaniced
  • one piece will be needed
8,41 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 6126

lock plate for hexagon nut , crankshaft (side of V-belt pulley)

lock plate for hexagon nut (Art.No. 6126) for mounting the V-belt pulley on crankshaft
  • original spare part
  • one piece will be needed
4,50 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 6128

hexagon nut for crankshaft (side of flywheel)

hexagon nut for mounting the flywheel on crankshaft
the lock plate (Art.No. 6130) have to be changed ater every disassembly of the flywheel.
  • turning moment: 137 Nm
  • galvaniced
  • original spare part
  • one piece will be needed
9,21 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 6129

lock plate for hexagon nut , crankshaft (side of flywheel)

lock plate for hexagon nut (Art.No. 6130) for mounting the flywheel on crankshaft
  • original spare part
  • one piece will be needed
4,50 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 6130

Flywheel new version

Complete overhauled flywheel for the Trabant P601 engine. Selaing system with piston rings. Delivery only atr exchange part.
The piston ring sealing will be not part of the delivery.
The sarter gear rim is premounted.
  • exchange part
  • one piece will be needed
Delivery only in exchange! Please send in advance one brake cylinder original IFA to our company.
74,55 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 7106

Sealing ring flywheel new version

Piston ring for sealing the left side of the crankshaft at the Trabant P601 engine.
Mounting place: clutch side.
Fit only to flywheels latest model.
  • price per piece
  • two pieces will be needed
12,21 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 8122

Flywheel old version

Flywheel for the Trabant P601 engine. Selaing system with oil seal.
The shaft sealing will be not part of the delivery.
The sarter gear rim is premounted.
  • original spare part
  • one piece will be needed
82,06 €inclusive VAT, plus shipping costs
0temporary not available
temporary not available

Art.No. 7105

Sealing for ball bearing cover shaft seal

Paper seal for the ball bearing cover at the crankshaft flywheel side.
Fit to Trabant 500,600 and 601 with the crank sealing system radial oil seal.
Please check at your car what kind of screw you need.
  • spezial paper sealing
  • made in Germany
2,25 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 8015

Sealing for ball bearing cover pistonring seal

Paper seal for the ball bearing cover at the crankshaft flywheel side.
Fit to Trabant 500,600 and 601 with the crank sealing system piston ring sealing.
Please check at your car what kind of screw you need.
  • spezial paper sealing
  • made in Germany
2,25 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 8016

Phillips countersunk-head screw for ball bearing cover

Recessed countersunk-head bolt inclusive gear washer for mounting the ball bearing cover at the crankshaft flywheel side.
Fit to Trabant 500,600 and 601 with the crank sealing system radial oil seal or piston ring seal.
Please check at your car what kind of screw you need.
  • three pieces will be needed
  • surface: galvanized zinc coated, silver
1,15 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 7509

Slotted-head screw for ball bearing cover

Slotted-head screw bolt inclusive gear washer for mounting the ball bearing cover at the crankshaft flywheel side.
Fit to Trabant 500,600 and 601 with the crank sealing system radial oil seal or piston ring seal.
Please check at your car what kind of screw you need.
  • three pieces will be needed
  • surface: galvanized zinc coated, silver
1,15 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 7510

Stud M8 x 40

Stud with M8-threads on bouth ends and total length of 42mm.
Threat length (abot 16mm and 19mm)
Mounting place: Trabant engine crank case, connection between crank case and cylinders.
  • fit to all Trabant 601 engines
  • Plain stud
  • 8 pieces will be needed
1,87 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 6369

Bolt-set engine

Screw kit for the Trabant engine.
Fit for all two stroke engines of Trabant 500,600 and 601
Survace: galvaniced
Contens:
  • 4x hexagon bolt long, M10
  • 2x hexagon bolt short, M10
  • 6x hexagon bolt M8
  • deilvery inclusive washers and secure washers
9,50 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 7511

Piston ring pliers

Piston ring mounting and demounting tool.
With this pliers the changing of the piston rings will be simple and save, because the rins are retained at the outside.
  • working dimensions: 1-100mm
  • surface: nickel-plated
  • with blue plastic handles
  • made in Germany
35,42 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 7619

Retainer sring for ventilation plate

Tension spring for mounting the rear ventilation plate at the Trabi engine.
Fit for all two stroke engines at Trabant 500,600 and 601.
Delivery inklusive plasitc protection hose.
  • inclusive PVC protection
  • surface of the spring: galvaniced
  • delivery as single part
  • 2 pieces will be needed
4,20 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 8431

Protection hose for retainer sring for ventilation plate

Plasitc protection hose for mounting at the tension spring rear ventilation plate at the Trabi engine.
Fit for all two stroke engines at Trabant 500,600 and 601.
  • delivery as single part
  • material: PVC black
  • 2 pieces will be needed
0,95 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 8433

Piston pin 20 x 56

Piston pin for Trabant 601 up to vintage: dezember 1984
  • lenght: 60 mm
  • diameter: 20mm
  • two pieces will be needed
24,20 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 8439

Bolt-set engine - gearbox

Screw kit for the connection of the Trabant engine and gearbox.
Fit for all two stroke engines of Trabant 500,600 and 601
Survace: galvaniced
Contens:
  • 4x hexagon bolt long, M8
  • 2x hexagon socket bolt short, M12
  • deilvery inclusive washers and secure washers
5,50 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 8451

Bearing cover for flywheel new version

One set of bearing cover for the piston ring sealing of the left side crankshaft Trabant P601 engine.
New producted spare part made in EU.
Mounting place: clutch side.
Fit only to flywheels latest model.
The set contens:
  • 1x steel bearing cover
  • 2x piston ring
  • 3x mounting screw with washer
  • 1x paper sealing
  • one kit will be needed
23,80 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 8464
The complete offer in spare parts for the motor Trabant 601

* All prices inclusive VAT and plus shipping costs.
© 2003 - 2021 LDM-tuning.de
Ersatzteile für Trabant, Wartburg und Barkas