Spare parts and supplies around the models 311, 312, 313

Category Spare parts and supplies around the models 311, 312, 313 has the following subcategorys:

The product category IFA-vehicles > Wartburg 311 / 312 / 313 is spread over 9 sites:

123456789
Show all products

Brush for starter Detail Spare-brushes of the starter engine to solder on at the coil set. Can be used for all kind of starters 6V and 12V left- and right turning (without Trabant 1.1, Wartburg 1.3 and Baraks B1000-1) mounting place: brushholder bas plate size: 16X19x7 delivery as an single part for each starter two pieces will needed
original spare part number: 8202.11-220:10	8,24 €inclusive VAT, plus shipping costs Delivery in 1-3 days Art.No. 785

Spring for brush starter Detail Pressure spring for the brushes of the starter engine. This spring will push the brush at the collector ring from the rotor shaft. Can be used for all kind of starters 6V and 12V left- and right turning (without Trabant 1.1, Wartburg 1.3 and Barkas B1000-1) mounting place: brushholder bas plate original spare part delivery as an single part for each starter two pieces will needed

original spare part number: 8202.11-220.6

1,55 €inclusive VAT, plus shipping costs Delivery in 1-3 days Art.No. 7629

Bolt for starter Detail Bolt of the Bearing case of the starter engine. Connection bolt will be mounted at the beraing case threadholes and on the other side it will hold the rear case cover. Delivery as a single part without nuts an washers. Can be used for all kind of starters 6V and 12V left- and right turning (without Trabant 1.1, Wartburg 1.3 and Barkas B1000-1) original spare part surface: galvaniced total length: 16.5 cm delivery as an single part for each starter two pieces will needed

original spare part number: 8202.1-000:4/1

2,93 €inclusive VAT, plus shipping costs Delivery in 1-3 days Art.No. 7658

Battery 6V 84Ah, dry ( not charched ) Detail Batterie for cars with 6V supply voltage. The capacity is 84 Ah. The starting power is 240A. We just deliver this battery dry and uncharched. Design fit to historical vehicles. length: 22,5 cm wide: 17,5 cm highness case: 20 cm total highness inclusive pins: 22 cm made in Germany
+7,50 Euro deposit	225,50 €inclusive VAT, plus shipping costs Delivery in 1-3 days Art.No. 1225

Plug for body Detail Small plug for holes diameter 5mm. Can be used for the car body. material: rubber, black total length: 27mm made in Germany

2,81 €inclusive VAT, plus shipping costs Delivery in 1-3 days Art.No. 7705

Cap for Ignition coil Detail Rubber cap for connection wires pin 1 and pin 15 at the ignition coils. Useable for the 40mm and original 60mm coils with ring pin connection. material: rubber, black

1,95 €inclusive VAT, plus shipping costs Delivery in 1-3 days Art.No. 7991

Screw-cap for brakeline 6 x 0,7 Detail Screw-cap for brakeline 6mm x 0,7mm. The screws can be mounted at steel or nickel-copper brake lines. Please count how much pieces zou need total. Fit to Barkas B1000, Multicar M22, M24, M25 and all vehicles with 6mm brake line. border: type E thread: M12x1 material: steel, galvaniced made in Germany

1,80 €inclusive VAT, plus shipping costs Delivery in 1-3 days Art.No. 7276 Delivery only at advance payment.

Upper sealing ring carburettor float case 24,2 x 29,8 x 1,5 Detail Special made fiber sealing as single part for sealing the float case on top to the carburettor. This sealing rings are made for the exact fitting and sealing of this components. Useable for the carburettos of the fire fighter pump with ZW1103 engine, and the Carburettor types: H 362- of the cars Framo, Wartburg 311,312,313 and some boat engines with this type of carburettor. size: inside diameter: 24,2mm outside diameter: 29,8mm thickness: 1,5mm one piece will be needed

2,25 €inclusive VAT, plus shipping costs Delivery in 1-3 days Art.No. 8157

Lower sealing ring carburettor float case 20,2 x 25 x 1,5 Detail Special made fiber sealing as single part for sealing the float case bottom side to the carburettor.(Screw) This sealing rings are made for the exact fitting and sealing of this components. Useable for the carburettos of the fire fighter pump with ZW1103 engine, and the Carburettor types: H 362- of the cars Framo, Wartburg 311,312,313 and some boat engines with this type of carburettor. size: inside diameter: 20,2mm outside diameter: 25mm thickness: 1,5mm one piece will be needed

2,15 €inclusive VAT, plus shipping costs Delivery in 1-3 days Art.No. 8158