Spare parts and supplies around the models 311, 312, 313

Category Spare parts and supplies around the models 311, 312, 313 has the following subcategorys:

The complete offer in Spare parts and supplies around the models 311, 312, 313

Sleeve rubber final drive (W311) Detail Rubber sleeve for Wartburg 311 outer joint universal drive shaft.
52,12 €inclusive VAT, plus shipping costs Delivery in 1-3 days Art.No. 6599

Drive joint rubber W311

Detail

Drive joint instert made of rubber for the wheel drive shaft Wartburg 311.
Mounting place gearbox side. New reproduction.

delivery as an single part
outside diameter:125mm
inside diameter: 59mm
material: rubbber, black
made in Germany
four pieces will be needed

24,23 €inclusive VAT, plus shipping costs

Delivery in 1-3 days

Art.No. 7850

Sleeve rubber (inner side)

Detail

Rubber sleeve gearbox side for the right and left universal shaft.
Fit for all universal shaft of the Wartburg 353 and Wartburg 312

material: rubber, black
two pieces will be needed
made in Europe
delivery as an single part without mounting spring and mounting strap

Additional needed mounting parts (not scope of delivery of the rubber boot):
2x Band clamp, long (part.-No.:6408)
2x Spring clamp (part.-No.:8222)
1x High performance grease with molybdenum, tube 100g (Art.-Nr.:6256)

15,90 €inclusive VAT, plus shipping costs

Delivery in 1-3 days

Art.No. 3148

Sleeve rubber set gear box side

Detail

One kit of rubber boot and assambly parts for the universal shaft gearbox side.
Fit for all universal shaft of the Wartburg 353 and Wartburg 312 right and left hand.
Scope ofe delivery:
1x Sleeve rubber set gear box side
2x Band clamp, long (part.-No.:6408)
2x Spring clamp (part.-No.:8222)
1x High performance grease with molybdenum, tube 100g (Art.-Nr.:6256)

one set will be needed for each drive shaft

28,84 €inclusive VAT, plus shipping costs

Delivery in 1-3 days

Art.No. 8224

Spring holder for rubber boot gearbox side

Detail

Spring clamp for mounting the rubber sleeve gearbox side at the drive shaft.
Fit for the right and left car side at all types of Wartburg 353 and Wartburg 312.
This part is an new reproduction made in Germany. Best replacement for the original one.
Made of stainless steel.
Simply to assamble also by mounted driveshaft.

material: spring steel, VA
two pieces will be needed
made in Germany
delivery as an single part
fit for Rubber boot gearbox side (Part.-No.:3147)

4,91 €inclusive VAT, plus shipping costs

Delivery in 1-3 days

Art.No. 8222

Shaft seal gearbox

Detail

Oil seal for the Wartburg 311 gearbox.

material: Viton
size: 32 x 50 x 7
type without additional dust lip

19,44 €inclusive VAT, plus shipping costs

Delivery in 1-3 days

Art.No. 6939

Sleeve rubber for central lubrication (W311)

Detail

Rubber sleeve for central lubrication system Wartburg 311.

material: Gummi
original spare parts

6,50 €inclusive VAT, plus shipping costs

Delivery in 1-3 days

Art.No. 7681

Cylindrical roller for freewheel 12x18

Detail

Single part of the cylindrical roller for the freewheel of the Wartburg 311 (up to frame number: 637057)

9 pieces will be needed
zero mark: diameter 12,00mm
length: 18mm
made in Germany

price for each one

2,95 €inclusive VAT, plus shipping costs

Delivery in 1-3 days

Art.No. 7394

Cylindrical roller for freewheel 12x12

Detail

Single part of the cylindrical roller for the freewheel of the Wartburg 311 (from frame number: 637057 ownwards)

10 pieces will be needed
zero mark: diameter 12,00mm
length: 12mm
made in Germany

price for each one

2,65 €inclusive VAT, plus shipping costs

Delivery in 1-3 days

Art.No. 3145

Collar for gear shifting shaft

Detail

Sealing sleeve mounted on top of the gearbox to save the gear change shaft.
Fit to all Wartburg 311, 312, 313 and 353 without vintage limit.

Material: rubber
one piece will be needed for intake gear change shaft (all types)
two pieces will be needed for gear change mechanism of stick shift mechanism fit to Wartburg 353
original number: 53080001008

18,90 €inclusive VAT, plus shipping costs

Delivery in 1-3 days

Art.No. 6981

Universal boot kit

Detail

Bellows for many exertions at automobiles, trailers, caravans and ships ...
size:

length:19cm diameter:10mm / 30mm
length:23cm diameter: 35mm / 35mm
length:15cm diameter:30mm / 42mm
length:13cm diameter:41mm / 48mm
length:12cm diameter:41mm / 55mm
different length and diameter combinable
length of the bellow pice: 95mm

17,28 €inclusive VAT, plus shipping costs

Delivery in 1-3 days

Art.No. 7010

Bulb retainer display instruments

Detail

Holder for bulbs as an checked secound hand part. Can be used for nearly all IFA vehicles.
Type with contact pin for wire plug: 6,3x0,8 (standart)
Useabe for bulbs 6V, 12V oder 12V 2W with Ba7S base as speedometer lightning, display and indecator lights.

delivery without bulb and pin
new Reproduction

4,90 €inclusive VAT, plus shipping costs

Delivery in 1-3 days

Art.No. 7843

Retro back up lamp for rear bumper

Detail

Chromed back up light for the mounting on top of the bumber.
The lamp made of high end fabrication and the design fit brilliant to historical cars.

colour: chromium-plated casing, clear glass
size: 11 x 5,5 cm
delivery without bulb
made in Germany
with E-icon

184,10 €inclusive VAT, plus shipping costs

Delivery in 5 days.

Art.No. 6876

Delivery only at advance payment.

Bulb retainer display instruments, screw pin

Detail

Holder for bulbs with screw pin for wire connection. Can be used for nearly all IFA vehicles.
Type with contact for screw connection: up tp 1,5 mmm².
Useabe for bulbs 6V, 12V oder 12V 2W with Ba7S base as speedometer lightning, display and indecator lights.

new spare part
delivery without bulb

6,10 €inclusive VAT, plus shipping costs

temporary not available

Art.No. 7844

Retro licence plate lights

Detail

Chromed reversing registration plate light.
Mounting with two M6 nuts.
The lamp made of high end fabrication and the design fit brilliant to historical cars.

colour: chromium-plated casing, clear lense
size: L=82mm x B=29mm x H=27mm
bolt distance: 45mm
delivery without bulb
made in Europe
mit E-Zeichen

16,86 €inclusive VAT, plus shipping costs

Delivery in 1-3 days

Art.No. 7989

Retro rear fog lamp for rear bumper

Detail

Chromed reversing fog light for the mounting on top of the bumber.
The lamp made of high end fabrication and the design fit brilliant to historical cars.

colour: chromium-plated casing, red glass
size: 11 x 5,5 cm
delivery without bulb
made in Germany
with E-icon

210,36 €inclusive VAT, plus shipping costs

Lieferbar innerhalb von 6-8 Wochen.

Art.No. 6877

Delivery only at advance payment.

Replacement glass for RETRO reverse lamp

Detail

Red glass as spare part for our RETRO reverse indication lamp

material: clear (white) glass
made in Germany

8,93 €inclusive VAT, plus shipping costs

temporary not available

Art.No. 7137

Replacement glass for RETRO rear fog lamp

Detail

Red glass as spare part for our RETRO fog light

material: red glass
made in Germany

19,99 €inclusive VAT, plus shipping costs

temporary not available

Art.No. 7136

2+1

1+1

Rubber button pad, 4mm, for engine bonnet (W311)

Detail

Rubber button pad for engine bonnet of old car body variant of Wartburg (typ 311, 312, 313). Mounting hole diameter: 6mm

diameter of rubber pad: 20 mm
thickness of rubber pad: 4 mm
length total: 21 mm
diameter of mounting rubber pin (without cone): 5,5 mm
biggest diamter of cone: 9 mm

2,38 €inclusive VAT, plus shipping costs

Delivery in 1-3 days

Art.No. 6735

Rubber button pad, 6mm, for engine bonnet (W311)

Detail

Rubber button pad for engine bonnet of old car body variant of Wartburg (typ 311, 312, 313). Mounting hole diameter: 6mm

diameter of rubber pad: 20 mm
thickness of rubber pad: 6 mm
length total: 21 mm
diameter of mounting rubber pin (without cone): 5,5 mm
biggest diamter of cone: 9 mm

2,38 €inclusive VAT, plus shipping costs

Delivery in 1-3 days

Art.No. 8575

Joint for trak rod W311, left-hand thread

Trak rod end with eleastomer bearing. Fit to Wartburg 311.
Shank type with lef hand thread M14 x 1,5.

original spare part
lock nut: trak rod nut
Castel nut: slotted nut M12 x 1,5
pint: split pin

36,50 €inclusive VAT, plus shipping costs

Delivery in 1-3 days

Art.No. 6592

Joint for trak rod W311, right-hand thread

Trak rod end with eleastomer bearing. Fit to Wartburg 311.
Shank type with right hand thread M14 x 1,5.

original spare part
lock nut: trak rod nut
Castel nut: slotted nut M12 x 1,5
pint: split pin

36,50 €inclusive VAT, plus shipping costs

temporary not available

Art.No. 6603

Alternator DC 6V

Detail

Dynamo for vehicles with 6V direct current.
Fit to the folloing cars: : Trabant, Wartburg 311, 312 und Framo.

new spare part (original-IFA-part)
type: 220W
scope of delivery without belt pulley

mostly the generator has an external regulator.

380,00 €inclusive VAT, plus shipping costs

Delivery in 1-3 days

Art.No. 761

Starter 6V

Starter for 6V vehicles.
Fit to the fallowing cars: Wartburg 311, 312, Framo und IFA F9

overhauled in Germany
your old starter have to be first shipped to our company for exchange

195,00 €inclusive VAT, plus shipping costs

Delivery in 1-3 days

Art.No. 6815

LDM-Design outer rear view mirror, right Detail chromed Design rear view mirrors for co-drivers side (right door) arm is made of zinc die casting (chromed) mounting in the same way like original rear view mirrors These outer rear view mirrors was elaborate handmade by LDM-tuning no series producktion!
Please note: Delivery without steel clamp!	88,20 €inclusive VAT, plus shipping costs Delivery in 1-3 days Art.No. 7063

LDM-Design outer rear view mirror, left Detail chromed Design rear view mirrors for drivers side (left door) arm is made of zinc die casting (chromed) mounting in the same way like original rear view mirrors These outer rear view mirrors was elaborate handmade by LDM-tuning no series producktion!
Please note: Delivery without steel clamp!	88,20 €inclusive VAT, plus shipping costs Delivery in 1-3 days Art.No. 6337

Spark plug terminal universal 5 kOhm Detail Best terminal without metalcoat for all versions of sparks. Good replacment as the old type of spark plugs with thread type M18. Resistance type suppressor: 5kOhm producer: NGK inclusive rubber seal for ignition wire and spark plug.
9,27 €inclusive VAT, plus shipping costs Delivery in 1-3 days Art.No. 7724

Spark plug M18 - 260, NGK Detail Spark plug for using at tow stroke engines with thread M18. Good replacement for the original spare part (T18). The heating rate complies 260 (cold spark plug), best use for water and air cooled engines special for tuning engines. Made by NGK, Japan. Bosch Nr. M260 T1
13,11 €inclusive VAT, plus shipping costs Lieferbar innerhalb von 6-8 Wochen. Art.No. 7531

Spark plug M18 - 175, ISOLATOR Detail M18 spark plug. This part is an NOS spare part with thread M18 x 1,5mm. The spanner gap is 26mm. The heat rating is cose to 175. Can be used for wather cooled two stroke engines like Wartburg, Barkas, Framo, ZW1103
12,50 €inclusive VAT, plus shipping costs temporary not available Art.No. 1192

Spark plug M18 - 175, NGK Detail Spark plug for using at tow stroke engines with thread M18. Good replacement for the original spare part (W18). The heating rate complies 175 (warm spark plug), best use for water cooled engines. Made by NGK, Japan. Bosch Nr. M175 T1 spanner gap: SW 21
11,32 €inclusive VAT, plus shipping costs Delivery in 1-3 days Art.No. 7529

Spark plug M18 - 225, NGK Detail Spark plug for using at tow stroke engines with thread M18. Good replacement for the original spare part (T18). The heating rate complies 225 (cold spark plug), best use for water and air cooled engines. Made by NGK, Japan. Bosch Nr. M225 T1
11,27 €inclusive VAT, plus shipping costs Delivery in 1-3 days Art.No. 7530

Reflector round, red (catseye) for rear bumper, metal ring

Detail

Round reflector for rear bumper corner of Trabant 500 and 600 (P50/60) or some other oldtimers, with additional aluminium frame around it.
Only partially fit to back light of Trabant 601 (mounting bolt could be to short).

Outer diameter: 63,5 mm (2,5")
Colour: red
refelector area: 20 cm²
aluminium ring frame
with base plate made of sheet metal
centric mounting bolt M5 x 15 mm

5,24 €inclusive VAT, plus shipping costs

temporary not available

Art.No. 6919

Reflector round, red (catseye) for rear bumper

Detail

Standard type of round reflector for rear bumper corner of Trabant 500 and 600 (P50/60)or some other oldtimers.
Only partially fit to back light of Trabant 601 (mounting bolt could be to short).

Outer diameter: 62,5 mm (2,46")
Colour: red
refelector area: 20 cm²
with base plate made of sheet metal
centric mounting bolt M5 x 15 mm

5,14 €inclusive VAT, plus shipping costs

Delivery in 1-3 days

Art.No. 6918

Magnet, complete for starter 12V

Detail

Solenoid switch for starter for Trabant 601, Wartburg 353 and Barkas B1000.

operating voltage: 12V
spare part made EU
one piece will be needed

58,79 €inclusive VAT, plus shipping costs

Delivery in 1-3 days

Art.No. 784

Magnet, complete for starter 6V Detail Magnet switch for all starter types: Trabant 500,600,601, Wartburg 311,312,313 and Barkas B1000 with 6V system. This is an NOS spare part.
Original spare part number: 8201.6/3-400/1	65,23 €inclusive VAT, plus shipping costs Delivery in 1-3 days Art.No. 780

Knob for push switch 6 / 12V

Detail

Button insert for the push switchs.
Colour: yellow
Can be used for many Old and Youngtimers.

original spare part
delivery as an single part with snap ring

Original spare part number: 8600.33-2

0,98 €inclusive VAT, plus shipping costs

Delivery in 1-3 days

Art.No. 7960

Switch 6 / 12V

Detail

Universal useable switch.
Please choose
Can be used for many Old and Youngtimers.

original spare part
Original number: 8600.34

switch knop

17,55 €inclusive VAT, plus shipping costs

Delivery in 1-3 days

Art.No. 7451

Switch for warning flasher 6V, Original

Detail

6V version of switch for warning flasher. Original spare part.
With red round push button.
Fit to voltage of 6V.
Best use for Old and Youngtimer with 6V electrical system.

delivery without control bulb
contol bulb:Bulb 6V 1,2W
original-spare part no.: 8600.31/1

92,51 €inclusive VAT, plus shipping costs

Delivery in 1-3 days

Art.No. 86

Wire set for switch for warning flasher 6V

Detail

Cable set for the 6V version of switch for warning flasher.
Fit to voltage of 6V.
Can be used for many Old and Youngtimers.
Best use for Trabant as connecton between flasher unit, fuse box and switch.

original spare part
length about:630mm
one set will be needed

9,85 €inclusive VAT, plus shipping costs

Delivery in 1-3 days

Art.No. 7441

Rubber cover for ignition key

Detail

Grip rubber for mounting at the ignition key.
This spare part is an original one.
Fit for the vehicles: Trabant, Wartburg, W50, Barkas LO, LD Multicar usw.

material: rubber, black
original spare parts
delivery as an single part

9,50 €inclusive VAT, plus shipping costs

Delivery in 1-3 days

Art.No. 8193

Delivery only at advance payment.

Spare key, copy is made from yor key number

Detail

Production of an spare key for door, ignition or fuel cap looks and so on...
You have to tell us your key number per email, fax or letter.
Keys for the vehicles: Trabant, Wartburg, W50, Barkas LO, LD Multicar usw.

delivery time about one to two weeks
all Trabant 601 / Trabant 1,1, Wartburg 353 / Wartburg 1,3 and Brakas B1000/ B100-1 keys possible

Please write here your keynumber in:
Reproduction time for key ca. 2-3 Wochen !!!nfertigung auf Kundenwunsch, KEINE Rücknahme, Umtausch oder Stornierung / Widerruf nach Zahlungseingang!

29,75 €inclusive VAT, plus shipping costs

Delivery in 1-3 days

Art.No. 1341

Delivery only at advance payment.

Rubber sealing cap for front direction indicator lamp (P50/P60/B1000/Multicar) Detail New produced sealing cap fit to old front flasher lights of Trabant 500 and 600 (P50/60), Barkas B1000 and Multicar truck and fit to Wartburg 311,312,313 and Framo, and fit to the side lights of the camp trailer INTERCAMP.
9,33 €inclusive VAT, plus shipping costs Delivery in 1-3 days Art.No. 7250

Universal brake line, CUNIFER 5m, 6mm Detail Brakepipeline 6 x 0,7 mm made of NiCuFe length: 5m for B1000, B1000-1, Mulicar M22, M24, M26, Framo, Warburg 311 and 313
price for each meter: 8,60 €/m	42,99 €inclusive VAT, plus shipping costs Delivery in 1-3 days Art.No. 7398

Protection cap for starter lite ( plastic )

Detail

Sealing cap to protect the starter wire (plus) against dust and moisture.
Fit to the vehicles: P70, Trabant, Wartburg, Multicar, Framo and Barkas.

made in Germany
one piece will be needed

6,85 €inclusive VAT, plus shipping costs

Delivery in 1-3 days

Art.No. 786

Sealing plate Rearlight

Detail

Rubber plate for the rear light of the Wartburg 311,312,313.

original spare part
material: rubber, black
two pieces will be needed for each car

13,60 €inclusive VAT, plus shipping costs

Delivery in 1-3 days

Art.No. 7439

Ignition coil 6V, diameter 40mm

Detail

This coils can be used for Trabant 500, 600 and 601, Wartburg 313 and Wartburg 313, Framo with voltage of 6V.
Made in Europe.
Sizes:

diameter: 40mm
total lenght:130mm
length of the aluminium case: 92mm
threads for connection wires: M4

30,46 €inclusive VAT, plus shipping costs

Lieferbar innerhalb von 6-8 Wochen.

Art.No. 7987

Ignition coil 6V, diameter 40mm, Germany

Detail

This coils can be used for Trabant 500, 600 and 601, Wartburg 313 and Wartburg 313, Framo with voltage of 6V.
Original spare part.
Sizes:

diameter: 40mm
total lenght:130mm
length of the aluminium case: 92mm
threads for connection wires: M4

67,33 €inclusive VAT, plus shipping costs

temporary not available

Art.No. 7990

Ignition coil 6V, diameter 62mm

Detail

This coils can be used for Trabant 500, 600 and 601, Wartburg 313 and Wartburg 313, Framo with voltage of 6V.
Original spare part.
Sizes:

diameter: 62mm
total lenght:156mm
length of the aluminium case: 121mm
threads for connection wires:M5
made in Germany

original spare part number: 8351.103/6

55,72 €inclusive VAT, plus shipping costs

Delivery in 1-3 days

Art.No. 810

Ring eye D12mm, connection 6mm hose

Detail

Ring terminal ideal for doing byself to fix fuel hoses.
Best use for many old- and Youngtimers to make fuel pessure pipes or normal pertol connection hoses.
Can be used for banjo screws D= 12mm

Eye diameter: 12mm
diameter pipe connection: 6mm

4,85 €inclusive VAT, plus shipping costs

Delivery in 1-3 days

Art.No. 7539

Ring eye D12mm with pipe bend

Detail

Ring terminal ideal for doing byself to fix fuel hoses.
Best use for many old- and Youngtimers to make fuel pessure pipes or normal pertol connection hoses.
Can be used for banjo screws D= 12mm

Eye diameter: 12mm
diameter pipe connection: 8mm
pipe bend: 90 degree
pipe length total: 74mm

15,38 €inclusive VAT, plus shipping costs

Delivery in 1-3 days

Art.No. 7517

Ring eye D12mm, connection 8mm hose

Detail

Ring terminal ideal for doing byself to fix fuel hoses.
Best use for many old- and Youngtimers to make fuel pessure pipes or normal pertol connection hoses.
Can be used for banjo screws D= 12mm

Eye diameter: 12mm
diameter pipe connection: 8mm

5,95 €inclusive VAT, plus shipping costs

Delivery in 1-3 days

Art.No. 7540

Ring eye D10mm with pipe bend

Detail

Ring terminal ideal for doing byself to fix fuel hoses.
Best use for many old- and Youngtimers to make fuel pessure pipes or normal pertol connection hoses.
Can be used for banjo screws D= 10mm

Eye diameter: 10mm
diameter pipe connection: 6mm
pipe bend: 90 degree
pipe length total: 55mm

14,99 €inclusive VAT, plus shipping costs

Delivery in 1-3 days

Art.No. 7516

Ring eye D10mm, connection 6mm hose

Detail

Ring terminal ideal for doing byself to fix fuel hoses.
Best use for many old- and Youngtimers to make fuel pessure pipes or normal pertol connection hoses.
Can be used for banjo screws D= 10mm

Eye diameter: 10mm
diameter pipe connection: 6mm

4,60 €inclusive VAT, plus shipping costs

Delivery in 1-3 days

Art.No. 7537

Ring eye D10mm, connection 8mm hose

Detail

Ring terminal ideal for doing byself to fix fuel hoses.
Best use for many old- and Youngtimers to make fuel pessure pipes or normal pertol connection hoses.
Can be used for banjo screws D= 10mm

Eye diameter: 10mm
diameter pipe connection: 8mm

4,90 €inclusive VAT, plus shipping costs

Delivery in 1-3 days

Art.No. 7538

Windscreen washer kit 6V

Detail

Set for windscreen washer system with electrical pump and water bottle
voltage: 6V
Scope of delivery:

bottle 1,5 liter
cap
metal holder
wash pump 6V

Ideal for upgrate the mechanical hand pump into an electrical system.

56,53 €inclusive VAT, plus shipping costs

temporary not available

Art.No. 7597

Brush for starter

Detail

Spare-brushes of the starter engine to solder on at the coil set.
Can be used for all kind of starters 6V and 12V left- and right turning (without Trabant 1.1, Wartburg 1.3 and Baraks B1000-1)
mounting place: brushholder bas plate

size: 16X19x7
delivery as an single part
for each starter two pieces will needed

original spare part number: 8202.11-220:10

8,24 €inclusive VAT, plus shipping costs

Delivery in 1-3 days

Art.No. 785

Spring for brush starter

Detail

Pressure spring for the brushes of the starter engine.
This spring will push the brush at the collector ring from the rotor shaft.
Can be used for all kind of starters 6V and 12V left- and right turning (without Trabant 1.1, Wartburg 1.3 and Barkas B1000-1)
mounting place: brushholder bas plate

original spare part
delivery as an single part
for each starter two pieces will needed

original spare part number: 8202.11-220.6

1,55 €inclusive VAT, plus shipping costs

Delivery in 1-3 days

Art.No. 7629

Bolt for starter

Detail

Bolt of the Bearing case of the starter engine.
Connection bolt will be mounted at the beraing case threadholes and on the other side it will hold the rear case cover.
Delivery as a single part without nuts an washers.
Can be used for all kind of starters 6V and 12V left- and right turning (without Trabant 1.1, Wartburg 1.3 and Barkas B1000-1)

original spare part
surface: galvaniced
total length: 16.5 cm
delivery as an single part
for each starter two pieces will needed

original spare part number: 8202.1-000:4/1

2,93 €inclusive VAT, plus shipping costs

Delivery in 1-3 days

Art.No. 7658

Battery 6V 84Ah, dry ( not charched )

Detail

Batterie for cars with 6V supply voltage. The capacity is 84 Ah. The starting power is 240A.
We just deliver this battery dry and uncharched.
Design fit to historical vehicles.

length: 22,5 cm
wide: 17,5 cm
highness case: 20 cm
total highness inclusive pins: 22 cm
made in Germany

+7,50 Euro deposit

225,50 €inclusive VAT, plus shipping costs

Delivery in 1-3 days

Art.No. 1225

Plug for body

Detail

Small plug for holes diameter 5mm.
Can be used for the car body.

material: rubber, black
total length: 27mm
made in Germany

2,81 €inclusive VAT, plus shipping costs

Delivery in 1-3 days

Art.No. 7705

Cap for Ignition coil

Detail

Rubber cap for connection wires pin 1 and pin 15 at the ignition coils.
Useable for the 40mm and original 60mm coils with ring pin connection.

material: rubber, black

1,95 €inclusive VAT, plus shipping costs

Delivery in 1-3 days

Art.No. 7991

Screw-cap for brakeline 6 x 0,7

Detail

Screw-cap for brakeline 6mm x 0,7mm. The screws can be mounted at steel or nickel-copper brake lines.
Please count how much pieces zou need total.
Fit to Barkas B1000, Multicar M22, M24, M25 and all vehicles with 6mm brake line.

border: type E
thread: M12x1
material: steel, galvaniced
made in Germany

1,80 €inclusive VAT, plus shipping costs

Delivery in 1-3 days

Art.No. 7276

Delivery only at advance payment.

Upper sealing ring carburettor float case 24,2 x 29,8 x 1,5

Detail

Special made fiber sealing as single part for sealing the float case on top to the carburettor.
This sealing rings are made for the exact fitting and sealing of this components.
Useable for the carburettos of the fire fighter pump with ZW1103 engine, and the Carburettor types: H 362- of the cars Framo, Wartburg 311,312,313 and some boat engines with this type of carburettor.
size:

inside diameter: 24,2mm
outside diameter: 29,8mm
thickness: 1,5mm
one piece will be needed

2,25 €inclusive VAT, plus shipping costs

Delivery in 1-3 days

Art.No. 8157

Lower sealing ring carburettor float case 20,2 x 25 x 1,5

Detail

Special made fiber sealing as single part for sealing the float case bottom side to the carburettor.(Screw)
This sealing rings are made for the exact fitting and sealing of this components.
Useable for the carburettos of the fire fighter pump with ZW1103 engine, and the Carburettor types: H 362- of the cars Framo, Wartburg 311,312,313 and some boat engines with this type of carburettor.
size:

inside diameter: 20,2mm
outside diameter: 25mm
thickness: 1,5mm
one piece will be needed

2,15 €inclusive VAT, plus shipping costs

Delivery in 1-3 days

Art.No. 8158

Sealing ring carburettor blowpipe main jet 11 x 15 x 1,0

Detail

Special made fiber sealing as single part for sealing the brass blowpipe for the main jet to the carburettor.
This sealing rings are made for the exact fitting and sealing of this components.
Useable for the carburettos of the fire fighter pump with ZW1103 engine, and the Carburettor types: H 362- of the cars Framo, Wartburg 311,312,313 and some boat engines with this type of carburettor.
size:

inside diameter: 11.1mm
outside diameter: 15,1mm
thickness: 1,0mm
one piece will be needed

1,95 €inclusive VAT, plus shipping costs

Delivery in 1-3 days

Art.No. 7974

Sealing ring carburettor air adjustment slide jet 8 x 11 x 1,0

Detail

Special made fiber sealing as single part for sealing the brass air adjustment slide jet to the carburettor (left hand).
This sealing rings are made for the exact fitting and sealing of this components.
Useable for the carburettos of the fire fighter pump with ZW1103 engine, and the Carburettor types: H 362- of the cars Framo, Wartburg 311,312,313 and some boat engines with this type of carburettor.
size:

inside diameter: 8,2mm
outside diameter: 11mm
thickness: 1,0mm
two pieces will be needed

1,85 €inclusive VAT, plus shipping costs

Delivery in 1-3 days

Art.No. 8170

Sealing ring carburettor air adjustment slide jet 6 x 9 x 1,0

Detail

Special made fiber sealing as single part for sealing the brass air adjustment slide jet to the carburettor (right hand)
This sealing rings are made for the exact fitting and sealing of this components.
Useable for the carburettos of the fire fighter pump with ZW1103 engine, and the Carburettor types: H 362- of the cars Framo, Wartburg 311,312,313 and some boat engines with this type of carburettor.
size:

inside diameter: 6,1mm
outside diameter: 9mm
thickness: 1,0mm
one piece will be needed

1,85 €inclusive VAT, plus shipping costs

Delivery in 1-3 days

Art.No. 8171

Sealing ring carburettor blowpipe jet

Detail

Special made rubber sealing as single part to seal the aluminuim blowpipe jet inside of the carburettor.
This sealing rings are made for the exact fitting and sealing of this components.
Useable for the carburettos of the fire fighter pump with ZW1103 engine, and the Carburettor types: H 362- of the cars Framo, Wartburg 311,312,313 and some boat engines with this type of carburettor.
size:

material: fuel resitant rubber
one piece will be needed

2,65 €inclusive VAT, plus shipping costs

Delivery in 1-3 days

Art.No. 8172

Spring for batten stripes

Detail

Wire spring for mounting the mouldings. Fit for Wartburg 311, 312, 313, and Wartburg 353.
This holder clip looks like an eyeglasses frame.
Best reproduction made in Germany.

material: steel
surface: galvaniced
Price per piece
delivery as an single part
best replacement and high quality, made in Germany

1,30 €inclusive VAT, plus shipping costs

Delivery in 1-3 days

Art.No. 8213

Sealing ring for fuel tank plug

Detail

Special copper ring with mineral fibre to seal the drain plug at the petrol tank bottom side.
Fit to all kind of Wartburg Wartburg 311, 312, 313 Limousine, Cabrio, Camping, Coupe as well to Wartburg353 and 1,3 Limousine, Tourist and Trans.

material: copper
special pressing ring
only one time useable

1,95 €inclusive VAT, plus shipping costs

Delivery in 1-3 days

Art.No. 8173

Sealing for Headlamp W311, W312, W313

Detail

Rubber ring for the headlamp Wartburg 311,312, 313

material: rubber, black
two pieces will be needed for each car

14,20 €inclusive VAT, plus shipping costs

Delivery in 1-3 days

Art.No. 8412

Bushing for starter motor

Detail

Busing made of braas for the starter of the Trabant 601, Wartburg 353 and Barkas B1000.
This bearing guides the armature in front and rear side.
Can be used for 6V and 12V starters.

delivery as an single part
original spear part
two pieces will be needed

5,90 €inclusive VAT, plus shipping costs

Delivery in 1-3 days

Art.No. 8440

Bulb retainer display instruments, additional negative terminal

Detail

Holder for bulbs as an new reproduction part. Can be used for nearly all IFA vehicles.
Type with two contact pins for wire plug: 6,3x0,8 (standart)
1x pin for plus terminal (+) and 1x pin for negative pin (-)
Useabe for bulbs 6V 2W or 12V 2W with Ba7S base as speedometer lightning, display and indecator lights.

New repoduction
delivery without bulb
made in EU

3,80 €inclusive VAT, plus shipping costs

temporary not available

Art.No. 8443

Fuel tank plug, single Part

Detail

Screw for the Wartburg petrol tank, special made of stainless steel.
Fit to all kind of Wartburg Wartburg 311, 312, 313 Limousine, Cabrio, Camping, Coupe as well to Wartburg353 and 1,3 Limousine, Tourist and Trans.

material: stainless steel
made in Germany
Delivery without sealings and without the small drain plug
one piece will be needed

15,15 €inclusive VAT, plus shipping costs

Delivery in 1-3 days

Art.No. 8517

Fuel tank plug, set

Detail

Kit of screw (plug) for the Wartburg petrol tank.
The special screw is made of stainless steel.
Fit to all kind of Wartburg Wartburg 311, 312, 313 Limousine, Cabrio, Camping, Coupe as well to Wartburg353 and 1,3 Limousine, Tourist and Trans.

made in Germany
Scope of delivery: 1x special fuel tank plug, 2x sealings (copper), 1x small drain plug (stainless steel)
one set will be needed

17,10 €inclusive VAT, plus shipping costs

Delivery in 1-3 days

Art.No. 8518

Brush for spark plugs

Detail

Brass brush for cleaning of spark plugs.

material: brass / wood
made in Germany
one piece will be needed

4,74 €inclusive VAT, plus shipping costs

Delivery in 1-3 days

Art.No. 8566

Retainer for main jet, carburettor H 362

Detail

Holder for main jet of the carburettor type H 362-.
This is en new german reproduction. Nozzle threat M5.
Spanner gap SW14 and threat M11.
Useable for the carburettos of the fire fighter pump with ZW1103 engine, and the Carburettor types: H 362- of the cars Framo, Wartburg 311,312,313 and some boat engines with this type of carburettor.

delivery as single part
without jet and without sealing
material: brass
threat: M10x1
one piece will be needed

15,80 €inclusive VAT, plus shipping costs

Delivery in 1-3 days

Art.No. 8579

Float needle valve, carburettor H 362

Detail

Special made float needle valve for the carburettor type H 362-.
This is en new german reproduction.
Spanner gap SW14 and threat M12.
Useable for the carburettos of the fire fighter pump with ZW1103 engine, and the Carburettor types: H 362- of the cars Framo, Wartburg 311,312,313 and some boat engines with this type of carburettor.

delivery as single part
without without sealing
material: brass
threat: M12
one piece will be needed

27,68 €inclusive VAT, plus shipping costs

Delivery in 1-3 days

Art.No. 8586

Sealing for float needle valve, carburettor H 362

Detail

Special made fiber sealing ring for float needle valve (LDM-part-no.:8586) for the carburettor type H 362-.
This is en new german reproduction.
Useable for the carburettos of the fire fighter pump with ZW1103 engine, and the Carburettor types: H 362- of the cars Framo, Wartburg 311,312,313 and some boat engines with this type of carburettor.

delivery as single part
material: fiber sealing
one piece will be needed

3,20 €inclusive VAT, plus shipping costs

Delivery in 1-3 days

Art.No. 8619

Float needle valve (M10) carburettor H 362-

Detail

The needle velve controls the volume of the float housing.
Mounting place inside of the foat housing cover.
Fit for Wartburg 311, 312, 313, Framo and the Barkas static engine ZW 1103. mounted at the fire fighter pump TS 8/8.
Please note: only fit to M10 threat connection at the float cover !
{L[reproduction][delivery without sealing ring][material: brass][nozzle: 20][typ: tongued][one piece will be needed]

15,22 €inclusive VAT, plus shipping costs

Delivery in 1-3 days

Art.No. 7876

The complete offer in Spare parts and supplies around the models 311, 312, 313

* All prices inclusive VAT and plus shipping costs.