This site in german: IFA-Fahrzeuge > Wartburg 311 / 312 / 313 > Motor 
You are here: > IFA-vehicles> Wartburg 311 / 312 / 313> Engine

Spare parts and supplies for the three cylinder two stroke engine around the models 311, 312, 313

The complete offer in Spare parts and supplies for the three cylinder two stroke engine around the models 311, 312, 313

V-belt 13x1030

V-Belt for the models Wartburg 311, 312 engines and Framo with V-pully without anti-vibration damper (mounting nut SW46 at the v-pully)
widness: 13mm
length: 1030mm
  • best qualitiy, made in Germany
17,80 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 7505

V-belt 13x1060

V-Belt for the models Wartburg 311, 312 engines and Framo with V-pully without anti-vibration damper (mounting nut SW46 at the v-pully)
widness: 13mm
length: 1060mm
  • best qualitiy, made in Germany
18,40 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 7506

V-pully wheel for crank shaft 1000ccm

Modificated v-pully wheel for crankshaft for the models Wartburg 311, 312 engines, Framo with V-pully without anti-vibration damper (mounting nut SW46)
  • scop of delivery inclusive two piston rings, but without outside steel ring
  • good qualitiy, made in Germany

Please note, we can only exchange you this spare part if you ship 1x V-pully to our company in advance!
Delivery only in exchange! Please send in advance one brake cylinder original IFA to our company.
86,67 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 7000

Ignition distributor cover IFA F9 Framo

Ignition distributor cover for the car models IFA F9 und Framo.
36,00 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 7043

crankshaft 900ccm

Complete overhauled crank shaft for the models Wartburg 311, 312 engines, Framo with V-pully without anti-vibration damper (mounting nut SW46)

Crankshaft sealings are modificated to piston ring sealing at the fly wheel side.
The old type of labyrinth seal is modificated to pistion ring seal.
  • delivery iclusive bronze bearings for the piston pins diameter: 18mm
  • high qualitiy, made in Germany

Please note, we can only exchange you this spare part if you ship 1x used crank shaft to our company in advance!
2000,00 €inclusive VAT, plus shipping costs
0temporary not available
temporary not available

Art.No. 7009

Crankshaft 1000ccm

Complete overhauled crank shaft for the models Wartburg 311, 312 engines, Framo with V-pully without anti-vibration damper (mounting nut SW46)

Crankshaft sealings are modificated to piston ring sealing pully- and fly wheel side.
  • with standard version of conrod
  • delivery iclusive needle bearings for the piston pins diameter: 20mm
  • good qualitiy, made in Germany

Please note, we can only exchange you this spare part if you ship 1x used crank shaft and 1x V-pully to our company in advance!
1800,00 €inclusive VAT, plus shipping costs
0temporary not available
temporary not available

Art.No. 6995

Cylinder head packing 900 ccm - 8 bolts with metal ring

Head packing for the 900 ccm, 3-cylinder two stroke engine.
Material consist of paper seal with dry graphite.
It fit to Wartburg 311, 312 Framo, DKW and motor boate with 0,9 Liter swept volume and 8 bolts for cylinder head mounting.
  • made in Germany
  • inner diameter cylinder: 72 mm
  • thickness: 1,2mm
  • one piece will be needed
47,50 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 6789

Cylinder head packing 1000 ccm - 8 bolts with metal ring

Head packing for the 1000 ccm, 3-cylinder two stroke engine.
Material consist of paper seal with dry graphite.
It fit to Wartburg 311, 312 Framo, DKW and motor boate with 1 Liter swept volume and 8 bolts for cylinder head mounting.
  • made in Germany
  • inner diameter cylinder: 76 mm
  • thickness: 1,2mm
  • one piece will be needed
29,51 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 8105

Cylinder head packing 900 ccm - 12 bolts with metal ring

Head packing for the 900 ccm, 3-cylinder two stroke engine.
Material consist of paper seal with dry graphite and matal ring.
It fit to Wartburg 311, 312 Framo, DKW and motor boate with 0,9 Liter swept volume and 12 bolts for cylinder head mounting.
  • made in Germany
  • inner diameter cylinder: 72 mm
  • thickness: 2,2mm
  • one piece will be needed
50,22 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 6788

Bearing fan shaft

One row roller bearing for the fan shaft thrue the cylinder head of the 900 ccm and 1000ccm 3-cylinder two stroke engines.
It fit to Wartburg 311, 312 Framo, DKW and motor boates.
  • made by FAG
  • not covered ball bearing
  • tow piece will be needed
9,86 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 7507

Self-aligning bearings fan shaft

Bearing for the fan shaft thrue the cylinder head of the 900 ccm 3-cylinder two stroke engines (old version)
It fit to Wartburg 311, 312 Framo, DKW and motor boates.
  • made by FAG
  • both sides with sealings
  • tow piece will be needed
34,90 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 7508

Exhaust manifold seal

Paper seal with dry graphite. It fit to all Wartburg 353, 312, 311 and B-1000 with 3-cylinder two stroke engine.
  • very good quality of material and with good dimension accuracy
  • without metall ring
  • inner diameter: 43 mm (1,693 inch)
  • three pieces will be needed
  • made in Germany (only available by LDM-Tuning)
3,85 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 3011

Exhaust manifold seal with metall ring

Paper seal with dry graphite. It fit to all Wartburg 353, 312, 311 and B-1000 with 3-cylinder two stroke engine. Usefull for all tuning engines for example RS 1000, Leutert.
  • brilliant quality with metall ring
  • inner diameter: 45 mm
  • three pieces will be needed
  • made in Germany
8,25 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 6706

Bolt for cylinder head

cylinder bols fit to:
  • Wartburg-353, 2-stroke, 3-cylinder,1000ccm or 1200ccm, 8 or 12 bolts
  • Wartburg-3112-stroke, 3-cylinder,900 or 1000ccm, 8 or 12 bolts
  • Barkas-B1000,2-stroke, 3-cylinder,1000ccm, 8 bolts
  • Framo 2-stroke, 3-cylinder 900ccm, 8 or 12 bolts



The tightening torque and the sequence of mounting of the cylinder head nuts you can find at (Details)
Special offer normaly 11,81 € now 8,88 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 6931

Piston ring sealing crank shaft (W353/B1000)

Special piston ring for the sealing of the crank case. Can be mounted at the flywheel and the v-pully side, crankshaft with 45 hp or 50 hp.
  • fit to 2-stroke-engines of Wartburg 353 and Barkas B1000
  • 4 piece will be needed for each engine
13,49 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 6903

safety plate flywheel (W353/B1000)

Locking plate for the five srews, which are necessary to mount the flywheel at crankshaft.
  • surface: galvanized with olive drap colour
  • fit to 2-stroke-engines of Wartburg 311, 312, 313, 353, Framo Barkas B1000
  • one piece will be needed for each engine
9,98 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 620

Special bolt flywheel (W353/B1000)

One-off-production of the hexagon screw for mounting the flywheel at the crankshaft.
  • tap: M8
  • spanner gap: 13
  • surface: galvanized
  • fit to 2-stroke-engines of Wartburg 311, 312, 313, 353, Framo, Barkas B1000
  • 5 pieces will be needed for each engine
6,20 €inclusive VAT, plus shipping costs
0temporary not available
temporary not available

Art.No. 6904

safety plate beltwheel (W353/B1000)

Locking plate for the two srews, which are necessary to mount the beltwheel at crankshaft.
  • surface: galvanized
  • fit to 2-stroke-engines of Wartburg, Barkas B1000
  • one piece will be needed for each engine
2,97 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 7154

Starter 6V

Starter for 6V vehicles.
Fit to the fallowing cars: Wartburg 311, 312, Framo und IFA F9
  • overhauled in Germany
  • your old starter have to be first shipped to our company for exchange
195,00 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 6815

Sealing set Carburettor H362

Paper sealing kit for carburettor type H 362- for Framo, Wartburg 311, 312, 313 and some boat engines with this carburettor type.
Best use to refresh the carburettor. All parts are made from the orignial patterns and our own quality grade.
Set consist of:

  • one set will be needed
  • material: sealing paper, Vulkanfieber, fuel resistant rubber
  • high quality made in Germany
16,99 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 8266

Upper sealing ring carburettor float case 24,2 x 29,8 x 1,5

Special made fiber sealing as single part for sealing the float case on top to the carburettor.
This sealing rings are made for the exact fitting and sealing of this components.
Useable for the carburettos of the fire fighter pump with ZW1103 engine, and the Carburettor types: H 362- of the cars Framo, Wartburg 311,312,313 and some boat engines with this type of carburettor.
size:
  • inside diameter: 24,2mm
  • outside diameter: 29,8mm
  • thickness: 1,5mm
  • one piece will be needed
2,25 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 8157

Lower sealing ring carburettor float case 20,2 x 25 x 1,5

Special made fiber sealing as single part for sealing the float case bottom side to the carburettor.(Screw)
This sealing rings are made for the exact fitting and sealing of this components.
Useable for the carburettos of the fire fighter pump with ZW1103 engine, and the Carburettor types: H 362- of the cars Framo, Wartburg 311,312,313 and some boat engines with this type of carburettor.
size:
  • inside diameter: 20,2mm
  • outside diameter: 25mm
  • thickness: 1,5mm
  • one piece will be needed
2,15 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 8158

Sealing ring carburettor blowpipe main jet 11 x 15 x 1,0

Special made fiber sealing as single part for sealing the brass blowpipe for the main jet to the carburettor.
This sealing rings are made for the exact fitting and sealing of this components.
Useable for the carburettos of the fire fighter pump with ZW1103 engine, and the Carburettor types: H 362- of the cars Framo, Wartburg 311,312,313 and some boat engines with this type of carburettor.
size:
  • inside diameter: 11.1mm
  • outside diameter: 15,1mm
  • thickness: 1,0mm
  • one piece will be needed
1,95 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 7974

Sealing ring carburettor air adjustment slide jet 8 x 11 x 1,0

Special made fiber sealing as single part for sealing the brass air adjustment slide jet to the carburettor (left hand).
This sealing rings are made for the exact fitting and sealing of this components.
Useable for the carburettos of the fire fighter pump with ZW1103 engine, and the Carburettor types: H 362- of the cars Framo, Wartburg 311,312,313 and some boat engines with this type of carburettor.
size:
  • inside diameter: 8,2mm
  • outside diameter: 11mm
  • thickness: 1,0mm
  • two pieces will be needed
1,85 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 8170

Sealing ring carburettor air adjustment slide jet 6 x 9 x 1,0

Special made fiber sealing as single part for sealing the brass air adjustment slide jet to the carburettor (right hand)
This sealing rings are made for the exact fitting and sealing of this components.
Useable for the carburettos of the fire fighter pump with ZW1103 engine, and the Carburettor types: H 362- of the cars Framo, Wartburg 311,312,313 and some boat engines with this type of carburettor.
size:
  • inside diameter: 6,1mm
  • outside diameter: 9mm
  • thickness: 1,0mm
  • one piece will be needed
1,85 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 8171

Retainer for main jet, carburettor H 362

Holder for main jet of the carburettor type H 362-.
This is en new german reproduction. Nozzle threat M5.
Spanner gap SW13 and threat M10.
Useable for the carburettos of the fire fighter pump with ZW1103 engine, and the Carburettor types: H 362- of the cars Framo, Wartburg 311,312,313 and some boat engines with this type of carburettor.
  • delivery as single part
  • without jet and without sealing
  • material: brass
  • threat: M10x1
  • one piece will be needed
13,39 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 8579

Sealing ring carburettor blowpipe jet

Special made rubber sealing as single part to seal the aluminuim blowpipe jet inside of the carburettor.
This sealing rings are made for the exact fitting and sealing of this components.
Useable for the carburettos of the fire fighter pump with ZW1103 engine, and the Carburettor types: H 362- of the cars Framo, Wartburg 311,312,313 and some boat engines with this type of carburettor.
size:
  • material: fuel resitant rubber
  • one piece will be needed
2,65 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 8172

Float needle valve, carburettor H 362

Special made float needle valve for the carburettor type H 362-.
This is en new german reproduction.
Spanner gap SW14 and threat M12.
Useable for the carburettos of the fire fighter pump with ZW1103 engine, and the Carburettor types: H 362- of the cars Framo, Wartburg 311,312,313 and some boat engines with this type of carburettor.
  • delivery as single part
  • without without sealing
  • material: brass
  • threat: M12
  • one piece will be needed
19,11 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 8586

Carburettor W311 1000ccm

Complete overhauled Carburettor for the three cylinder Wartburg 311 engine with 1000 ccm
cylinder capacity. delivery without intake pipe.
Carburettor type: H 362-24
{[high quality from Germany]}
Please note, we can only exchange you this spare part if you ship 1x carburettor H 362-24 to our company in advance!
Overhaul part, please send your carburettor Wartburg 311 in advance to our company
329,00 €inclusive VAT, plus shipping costs
Lieferbar innerhalb von 6-8 Wochen.

Art.No. 7030

Sealing ( carburettor-flange )

Paper sealing between Carburettor suction pipe.
Carburettor type: H 362-24 and Carburettor type: H 362-12
{[high quality from Germany]}
3,64 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 7124

Sealing carburettor-case

Paper sealing for the case of the float Carburettor for Wartburg 311 and Framo.
Carburettor type: H 362-24 and Carburettor type: H 362-12
{[high quality made in Germany]}
4,51 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 7541

Alternator DC 6V

Dynamo for vehicles with 6V direct current.
Fit to the folloing cars: : Trabant, Wartburg 311, 312 und Framo.
  • new spare part (original-IFA-part)
  • type: 220W
  • scope of delivery without belt pulley

mostly the generator has an external regulator.
380,00 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 761

Regulator and cotout relay ( 6V/220W ) for DC 6V Dynamo

External mechanical regulator for use at the DC dynamo to control the battery voltage.
Fit to Trabant 500, 600 and 601, Framo, Wartburg 311
Original spare part.
  • voltage: 6V
  • use for DC dynamo: 220W
  • made in Germany
original spare part number: AKA 8101.7
95,22 €inclusive VAT, plus shipping costs
0temporary not available
temporary not available

Art.No. 776

Regulator and cotout relay 12V/220W for DC 6V Dynamo

External mechanical regulator for use at the DC dynamo to control the battery voltage.
Fit to Trabant 500, 600 and 601, Framo, Wartburg 311
Original spare part.
  • voltage: 12V
  • use for DC dynamo: 220W
  • made in Germany
original spare part number: AKA 8102.9
95,22 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 7904
1+1

Three-lever contact breaker base plate, complete

Ignition base plate complete with 3x contact breaker and 3x ignition capacitor
Fit to:
  • Wartburg 311
  • Wartburg 312
  • Wartburg 313
  • Wartburg 353
  • Barkas B1000 with 3 cylinder 2-stroke engine
Original spare part number: 8321.4-100/2
69,11 €inclusive VAT, plus shipping costs
0temporary not available
temporary not available

Art.No. 3160

Contact rail for contact breaker base plate

Metal stripe to connect the contact breaker and the ignition capacitor.
Original spare part, surface: galvaniced.
Fit to:
  • Wartburg 311
  • Wartburg 312
  • Wartburg 313
  • Wartburg 353
  • Barkas B1000 with 3 cylinder 2-stroke engine
  • with mechanical contact breaker ignition system
  • three piece will be needed
original spare part number: 8321.4-100:2
1,30 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 7810

Mounting screw for ignition base plate

Screw made of stainless steel slotted for mounting and adjusting of the ignition base plate for Wartburg 312, 353, B1000 und boat engines.
Fit to contact braker or electronic ignition systems.
  • two pieces will be needed
  • delivery inclusive washer
  • material: stainless steel
1,10 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 7718

Contact breaker, EU

Inexpensively breaker for the ignition controling.
Used for 2 stroke engiene Trabant, Wartburg and Barkas
for Trabant you will need two pices Wartburg and Barkas got three of them.
  • inclusive lube felt
  • material: plastic
  • original spare part
  • made in EU
2,49 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 7299

Contact breaker, original

Breaker for the ignition controling. Best quality.
used for 2 stroke engiene Trabant, Wartburg and Barkas
for Trabant you will need two pices
Wartburg and Barkas got three of them
  • without lube felt
  • material: plastic
  • original spare part
  • made in Germany
6,88 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 805

Contact breaker Pertinax

used for 2 stroke engiene Trabant, Wartburg and Barkas
for Trabant you will need two pices
Wartburg and Barkas got three of them
  • old type of contact braker
  • made of fabric reinforced plastic
  • made in Germany
15,50 €inclusive VAT, plus shipping costs
0temporary not available
temporary not available

Art.No. 6715

Ignition capacitor

Spark capacitor fit to all Trabant, Wartburg and Barkas with tow stroke engine.
  • Trabant: 2 pieces will be needed
  • Wartburg: 3 pieces will be needed
  • B1000: 3 pieces will be needed
2,54 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 806

Spark plug terminal universal 5 kOhm

Best terminal without metalcoat for all versions of sparks.
Good replacment as the old type of spark plugs with thread type M18.
Resistance type suppressor: 5kOhm
producer: NGK
inclusive rubber seal for ignition wire and spark plug.
5,39 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 7724

Spark plug terminal M18

fit to old type of spark plugs with thread type M18
6,20 €inclusive VAT, plus shipping costs
0temporary not available
temporary not available

Art.No. 6644

Piston ring pliers

Piston ring mounting and demounting tool.
With this pliers the changing of the piston rings will be simple and save, because the rins are retained at the outside.
  • working dimensions: 1-100mm
  • surface: nickel-plated
  • with blue plastic handles
  • made in Germany
35,42 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 7619

Drive joint rubber W311

Drive joint instert made of rubber for the wheel drive shaft Wartburg 311.
Mounting place gearbox side. New reproduction.
  • delivery as an single part
  • outside diameter:125mm
  • inside diameter: 59mm
  • material: rubbber, black
  • made in Germany
  • four pieces will be needed
14,57 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 7850

Freeze cap 34mm

Pot shape plug for secure the motor block for freeze demages.
Fit to all cooling water holes diameter 34mm for the Wartburg and Barkas with two stroke motor.
made in Germany
  • three pieces will be needed
2,25 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 7886

Freeze cap

Plate shape plug for secure the motor block for freeze demages.
Fit to all cooling water holes diameter 36mm for the Wartburg and Barkas with two stroke motor.
made in Germany
  • three pieces will be needed
6,76 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 7255

Seal for flange suction pipe - engine block

Paper seal for the vehicles Barkas V901, Wartburg 311, 312, 313 and Robur LO.
Fit to the flange of the inlet manifold of the carburettor type 36 F,H 362-12 und H 362-24. Mounted:
  • between flange inlet manifold and engine mount
  • one pieces needed
  • fit for 900ccm and 1000ccm engines
7,50 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 7910

Seal for flange suction pipe - engine block

Paper seal for flange of the inlet manifold of the carburettor type BVF 40 F, Jijkov and 36F. Mounted:
  • between flange inlet manifold and engine mount
  • one pieces needed
  • fit for Wartburg 353, B1000 and Wartburg 312
7,50 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 6897

Cylinder head packing, steel sealing

Cylinder head packing is made of an special kind of sealing paper with dry graphite finish. The cylinder are sealed by single metal-rings for each one, which are fixed at the paper packing.
one piece will be needed
  • Wartburg311,312 and 313, 2-stroke, 3-cylinder, 1000ccm, 8 bolts
  • Wartburg-353, 2-stroke, 3-cylinder, 1000ccm, 8 bolts
  • Barkas-B1000,2-stroke, 3-cylinder, 1000ccm, 8 bolts
  • compession sealing: steel
  • high quality made in Europe


The tightening torque and the sequence of mounting of the cylinder head nuts you can find at Art.No.:6318
12,49 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 3120

Cylinder head packing, copper sealing

Cylinder head packing is made of an special kind of sealing paper with dry graphite finish. The cylinder are sealed by single copper-metal-rings for each one, which are fixed at the paper packing.
one piece will be needed
  • Wartburg311,312 and 313, 2-stroke, 3-cylinder, 1000ccm, 8 bolts
  • Wartburg-353, 2-stroke, 3-cylinder, 1000ccm, 8 bolts
  • Barkas-B1000,2-stroke, 3-cylinder, 1000ccm, 8 bolts
  • compession sealing: copper
  • high quality made in Europe


The tightening torque and the sequence of mounting of the cylinder head nuts you can find at Art.No.:6318
34,22 €inclusive VAT, plus shipping costs
0temporary not available
temporary not available

Art.No. 7986

Dial gauge shock proof

High quality dial indicator for example to adujst the ignition timing.
  • case diameter: 58mm
  • tolerance: 0,01mm
  • effective range: 0-10mm
  • made in Germany
  • scope of delivery without seperate extension pin
  • shock proof
79,98 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 6821

Adapter M18 ignition ajustment

adapter for the dial gauge to adjust the ignition point.
Fit to the spark plug tap M18. Hexagon nut for mounting SW 22.
usefull for the fallowing vehicles:
  • made in Germany
  • material: brass
  • Trabant 500,600,601
  • Wartburg 311
  • Framo
  • IFA F8 / F9
  • P70
28,99 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 6819

Extensions pin for Dial gauge, 60mm

Extension for dial gauge. Fit to all offered gauges
  • thread: M2,5
  • diameter: 4mm
  • tolerance: 0,01mm
  • effective range: 0-10mm
  • made in China
  • scope of delivery without seperate extension pin
  • non shock proof
3,09 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 7302

Dial gauge simple type

High quality dial indicator for example to adujst the ignition timing.
  • case diameter: 58mm
  • tolerance: 0,01mm
  • effective range: 0-10mm
  • made in Germany
  • scope of delivery without seperate extension pin
  • non shock proof
49,10 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 6820

Dial gauge simple type

Cheap dial indicator for example to adujst the ignition timing.
  • case diameter: 58mm
  • tolerance: 0,01mm
  • effective range: 0-10mm
  • made in China
  • scope of delivery without seperate extension pin
  • non shock proof
14,99 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 7300

Dial gauge digitale type

Good quality dial indicator for example to adujst the ignition timing.
  • case diameter: 58mm
  • tolerance: 0,01mm
  • effective range: 0-10mm
  • made in China
  • scope of delivery without seperate extension pin
  • non shock proof
45,55 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 7301

Retainer spring for clutch cable

Retainer wire to fic the clutch cable at the vehicle frame or holder.
Can be used for Fahrzeuge: Wartburg 311,312, 313, Wartburg 353 and 1.3 and Barkas B1000 und B1000-1.
High quality reproduction.
  • material: spring steel
  • one piece will be needed
3,90 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 8313

Spring for idle screw, carburettor

Pressur spring for idle adjusting screw at the carburettor.
Fit for:
  • Straitdraft carburetor H 362- : Wartburg 311, 312 and 313
  • Straitdraft carburetor H 362- : Framo V901
  • Straitdraft carburetor H 362- : fire fighter pump TS8
  • Straitdraft carburetor : P70, F8
  • Downdraught carburettor BVF36F: Robur LO, Wartburg 353
  • Downdraught carburettor BVF40F: Wartburg 353, Barkas B1000
  • Block carburettor 28HB: Trabant 500,600 and 601

  • delivery as single part
  • surface: galvaniced
  • made in Germany
  • one piece will be needed
1,49 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 8459

Piston ring sealing crank shaft (W353/B1000)

Special piston ring for the sealing of the crank case. Can be mounted at the flywheel and the v-pully side, crankshaft with 45 hp or 50 hp.
  • fit to 2-stroke-engines of Wartburg 353 and Barkas B1000
  • 4 piece will be needed for each engine
25,70 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 8556
The complete offer in Spare parts and supplies for the three cylinder two stroke engine around the models 311, 312, 313

* All prices inclusive VAT and plus shipping costs.
© 2003 - 2021 LDM-tuning.de
Ersatzteile für Trabant, Wartburg und Barkas