Trabant 500/600

Category Trabant 500/600 has the following subcategorys:

The complete offer in Trabant 500/600

Universal boot kit

Detail

Bellows for many exertions at automobiles, trailers, caravans and ships ...
size:

length:19cm diameter:10mm / 30mm
length:23cm diameter: 35mm / 35mm
length:15cm diameter:30mm / 42mm
length:13cm diameter:41mm / 48mm
length:12cm diameter:41mm / 55mm
different length and diameter combinable
length of the bellow pice: 95mm

17,28 €inclusive VAT, plus shipping costs

Delivery in 1-3 days

Art.No. 7010

Grill for air intake T500 / 600

Detail

Oval grill for the front air intake of the Trabant 500 and 600.
High quality new reproduction.

delivery as an single part
length:131mm
widness: 87mm
material: aluminium
made in Germany
two pieces will be needed

27,61 €inclusive VAT, plus shipping costs

Delivery in 1-3 days

Art.No. 7852

Drive joint rubber T500 / 600

Detail

Drive joint instert made of rubber for the wheel drive shaft Trabant 500 and 600.
Mounting place gearbox side. New reproduction.

delivery as an single part
outside diameter:100mm
inside diameter: 37mm
material: rubbber, black
made in Germany
four pieces will be needed

14,57 €inclusive VAT, plus shipping costs

Delivery in 1-3 days

Art.No. 7851

Retro back up lamp for rear bumper

Detail

Chromed back up light for the mounting on top of the bumber.
The lamp made of high end fabrication and the design fit brilliant to historical cars.

colour: chromium-plated casing, clear glass
size: 11 x 5,5 cm
delivery without bulb
made in Germany
with E-icon

134,63 €inclusive VAT, plus shipping costs

Delivery in 1-3 days

Art.No. 6876

Bulb retainer display instruments, screw pin

Detail

Holder for bulbs with screw pin for wire connection. Can be used for nearly all IFA vehicles.
Type with contact for screw connection: up tp 1,5 mmm².
Useabe for bulbs 6V, 12V oder 12V 2W with Ba7S base as speedometer lightning, display and indecator lights.

new spare part
delivery without bulb

6,10 €inclusive VAT, plus shipping costs

temporary not available

Art.No. 7844

Bulb retainer display instruments

Detail

Holder for bulbs as an checked secound hand part. Can be used for nearly all IFA vehicles.
Type with contact pin for wire plug: 6,3x0,8 (standart)
Useabe for bulbs 6V, 12V oder 12V 2W with Ba7S base as speedometer lightning, display and indecator lights.

delivery without bulb and pin
new Reproduction

4,90 €inclusive VAT, plus shipping costs

Delivery in 1-3 days

Art.No. 7843

Retro licence plate lights

Detail

Chromed reversing registration plate light.
Mounting with two M6 nuts.
The lamp made of high end fabrication and the design fit brilliant to historical cars.

colour: chromium-plated casing, clear lense
size: L=82mm x B=29mm x H=27mm
bolt distance: 45mm
delivery without bulb
made in Europe
mit E-Zeichen

16,86 €inclusive VAT, plus shipping costs

Delivery in 1-3 days

Art.No. 7989

Retro rear fog lamp for rear bumper

Detail

Chromed reversing fog light for the mounting on top of the bumber.
The lamp made of high end fabrication and the design fit brilliant to historical cars.

colour: chromium-plated casing, red glass
size: 11 x 5,5 cm
delivery without bulb
made in Germany
with E-icon

159,88 €inclusive VAT, plus shipping costs

Lieferbar innerhalb von 6-8 Wochen.

Art.No. 6877

Replacement glass for RETRO reverse lamp

Detail

Red glass as spare part for our RETRO reverse indication lamp

material: clear (white) glass
made in Germany

8,93 €inclusive VAT, plus shipping costs

temporary not available

Art.No. 7137

Replacement glass for RETRO rear fog lamp

Detail

Red glass as spare part for our RETRO fog light

material: red glass
made in Germany

19,99 €inclusive VAT, plus shipping costs

temporary not available

Art.No. 7136

Reflector round, red (catseye) for rear bumper

Detail

Standard type of round reflector for rear bumper corner of Trabant 500 and 600 (P50/60)or some other oldtimers.
Only partially fit to back light of Trabant 601 (mounting bolt could be to short).

Outer diameter: 62,5 mm (2,46")
Colour: red
refelector area: 20 cm²
with base plate made of sheet metal
centric mounting bolt M5 x 15 mm

5,14 €inclusive VAT, plus shipping costs

Delivery in 1-3 days

Art.No. 6918

Reflector round, red (catseye) for rear bumper, metal ring

Detail

Round reflector for rear bumper corner of Trabant 500 and 600 (P50/60) or some other oldtimers, with additional aluminium frame around it.
Only partially fit to back light of Trabant 601 (mounting bolt could be to short).

Outer diameter: 63,5 mm (2,5")
Colour: red
refelector area: 20 cm²
aluminium ring frame
with base plate made of sheet metal
centric mounting bolt M5 x 15 mm

5,24 €inclusive VAT, plus shipping costs

temporary not available

Art.No. 6919

1+1

Cover plate, front Trabant 500,600

Detail

New produced spare cover under the front bumber of Trabant 500 and 600 (P50/60).
High quality inclusive mounted cover holder.
Smooth surface, colour grey.

material: GFK

Plaese note: + buckly goods fees

185,64 €inclusive VAT, plus shipping costs

Delivery in 1-3 days

Art.No. 7790

Chromium-plated ring for front direction indicator lamp (P50/P60) Detail New produced chromed ring for old front flash lights of Trabant 500 and 600 (P50/60).
13,25 €inclusive VAT, plus shipping costs Delivery in 1-3 days Art.No. 7249

Rubber sealing cap for front direction indicator lamp (P50/P60/B1000/Multicar) Detail New produced sealing cap fit to old front flasher lights of Trabant 500 and 600 (P50/60), Barkas B1000 and Multicar truck and fit to Wartburg 311,312,313 and Framo, and fit to the side lights of the camp trailer INTERCAMP.
9,33 €inclusive VAT, plus shipping costs Delivery in 1-3 days Art.No. 7250

Alternator DC 6V

Detail

Dynamo for vehicles with 6V direct current.
Fit to the folloing cars: : Trabant, Wartburg 311, 312 und Framo.

new spare part (original-IFA-part)
type: 220W
scope of delivery without belt pulley

mostly the generator has an external regulator.

380,00 €inclusive VAT, plus shipping costs

Delivery in 1-3 days

Art.No. 761

Regulator and cotout relay ( 6V/220W ) for DC 6V Dynamo

Detail

External mechanical regulator for use at the DC dynamo to control the battery voltage.
Fit to Trabant 500, 600 and 601, Framo, Wartburg 311
Original spare part.

voltage: 6V
use for DC dynamo: 220W
made in Germany

original spare part number: AKA 8101.7

95,22 €inclusive VAT, plus shipping costs

temporary not available

Art.No. 776

Regulator and cotout relay 12V/220W for DC 6V Dynamo

Detail

External mechanical regulator for use at the DC dynamo to control the battery voltage.
Fit to Trabant 500, 600 and 601, Framo, Wartburg 311
Original spare part.

voltage: 12V
use for DC dynamo: 220W
made in Germany

original spare part number: AKA 8102.9

95,22 €inclusive VAT, plus shipping costs

Delivery in 1-3 days

Art.No. 7904

1+1

Dial gauge shock proof

Detail

High quality dial indicator for example to adujst the ignition timing.

case diameter: 58mm
tolerance: 0,01mm
effective range: 0-10mm
made in Germany
scope of delivery without seperate extension pin
shock proof

107,04 €inclusive VAT, plus shipping costs

Delivery in 1-3 days

Art.No. 6821

Adapter M18 ignition ajustment

Detail

adapter for the dial gauge to adjust the ignition point.
Fit to the spark plug tap M18. Hexagon nut for mounting SW 22.
usefull for the fallowing vehicles:

made in Germany
material: brass
Trabant 500,600,601
Wartburg 311
Framo
IFA F8 / F9
P70

28,99 €inclusive VAT, plus shipping costs

Delivery in 1-3 days

Art.No. 6819

Extensions pin for Dial gauge, 60mm

Detail

Extension for dial gauge. Fit to all offered gauges

thread: M2,5
diameter: 4mm
tolerance: 0,01mm
effective range: 0-10mm
made in China
scope of delivery without seperate extension pin
non shock proof

3,09 €inclusive VAT, plus shipping costs

Delivery in 1-3 days

Art.No. 7302

Dial gauge simple type

Detail

High quality dial indicator for example to adujst the ignition timing.

case diameter: 58mm
tolerance: 0,01mm
effective range: 0-10mm
made in Germany
scope of delivery without seperate extension pin
non shock proof

65,07 €inclusive VAT, plus shipping costs

Delivery in 1-3 days

Art.No. 6820

Dial gauge digitale type

Detail

Good quality dial indicator for example to adujst the ignition timing.

case diameter: 58mm
tolerance: 0,01mm
effective range: 0-10mm
made in China
scope of delivery without seperate extension pin
non shock proof

45,55 €inclusive VAT, plus shipping costs

Delivery in 1-3 days

Art.No. 7301

Dial gauge simple type

Detail

Cheap dial indicator for example to adujst the ignition timing.

case diameter: 58mm
tolerance: 0,01mm
effective range: 0-10mm
made in China
scope of delivery without seperate extension pin
non shock proof

24,96 €inclusive VAT, plus shipping costs

Delivery in 1-3 days

Art.No. 7300

Seal for connection between ignition coil and ignition cable

Detail

Rubber protection cap for ingniton coil. Protection against dust and spash water. Also for universal use.

lenght: 23 mm
big inner diameter: ca. 14 mm
small inner diameter: ca. 6 mm
made of high quality rubber (soft) rubber
colour: black

3,55 €inclusive VAT, plus shipping costs

Delivery in 1-3 days

Art.No. 6892

Collar - shaped ring, steering column, old version

Detail

Rubber bearing for the steering column. The ring will be móunted at the cross holder and fixes the bearing shells (LDM-no.: 1057)

1 piece will be needed
Fit to all Trabant types
material: rubber

38,44 €inclusive VAT, plus shipping costs

Delivery in 1-3 days

Art.No. 1056

Collar - shaped ring, steering column, new version

Detail

Rubber bearing for the steering column. The ring will be móunted at the cross holder and fixes the bearing shells (LDM-no.: 1057)
made in Germany, original spare part.

1 piece will be needed
Fit to all Trabant types
material: rubber

18,11 €inclusive VAT, plus shipping costs

Delivery in 1-3 days

Art.No. 7303

Guide cap- set, steering column

Detail

Upper bearing part for the Trabant steering column.
The price is for one set (inclusive 3 pieces).
Fit to Trabant 500, 600, 601 and Trabant 1.1
Slide bearing for Collar - shaped rind, steering column

material: plastic
original spare part
one set will be needed

original spare part number: 1342913204031303

19,50 €inclusive VAT, plus shipping costs

Delivery in 1-3 days

Art.No. 1057

1+1

T-piece with integrated non-return valve for windscreen washer Detail T-piece with two integrated non-return valves Purpose-built to use it in windscreen washer systems with manual pump. All connections are labelled: S - suction connection P - pump connection D - pressure connection
11,04 €inclusive VAT, plus shipping costs temporary not available Art.No. 6926

Non-return valve for windscreen washer Detail Check valve for the manual Trabant windscreen washer.
6,49 €inclusive VAT, plus shipping costs Delivery in 1-3 days Art.No. 1112

Windscreen washer system, manual, complete

Detail

Original spare part screen washer for manual operation.
with:

receptacle
2x non-return valve (Art.No. 1112)
T-piece
hose
suction pump (Art.No. 1126)
double jet (Art.No. 1124)

56,20 €inclusive VAT, plus shipping costs

temporary not available

Art.No. 6181

Suction pump for windscreen washer

Detail

Mechanical operating pump for the windshield cleaning system.
Fit to Trabant 500, 600 and 601.

original spare part
delivery pree mounted part inclusive attachment nut

32,49 €inclusive VAT, plus shipping costs

Delivery in 1-3 days

Art.No. 1126

Cap for water vessel for windscreen washer system Detail Plastic cap with mounting sprap for the water bottle of the windscreen washer system. The plug close up the refilling hole. To use at many reservoir bottles with electrical or mechanical pump. fit to follow washer systems: Trabant 601, Trabant 1.1, Wartburg 1.3, Wartburg 353, Multicar, W50 and so on
4,75 €inclusive VAT, plus shipping costs Delivery in 1-3 days Art.No. 7357

LDM-Design outer rear view mirror, right Detail chromed Design rear view mirrors for co-drivers side (right door) arm is made of zinc die casting (chromed) mounting in the same way like original rear view mirrors These outer rear view mirrors was elaborate handmade by LDM-tuning no series producktion!
Please note: Delivery without steel clamp!	68,20 €inclusive VAT, plus shipping costs Delivery in 1-3 days Art.No. 7063

LDM-Design outer rear view mirror, left Detail chromed Design rear view mirrors for drivers side (left door) arm is made of zinc die casting (chromed) mounting in the same way like original rear view mirrors These outer rear view mirrors was elaborate handmade by LDM-tuning no series producktion!
Please note: Delivery without steel clamp!	68,20 €inclusive VAT, plus shipping costs Delivery in 1-3 days Art.No. 6337

Telescopic shock absorber P50

Detail

Directional pressure telescopic shock absorber for leaf spring. Fit to front and rear axle of Trabant 500, 600.
scope of delivery:

complete inclusive bushing, lower bushing diameter 10mm
Made in Germany

63,93 €inclusive VAT, plus shipping costs

Delivery in 1-3 days

Art.No. 7086

Spark plug terminal universal 5 kOhm Detail Best terminal without metalcoat for all versions of sparks. Good replacment as the old type of spark plugs with thread type M18. Resistance type suppressor: 5kOhm producer: NGK inclusive rubber seal for ignition wire and spark plug.
7,45 €inclusive VAT, plus shipping costs Delivery in 1-3 days Art.No. 7724

Spark plug M18 - 260, NGK Detail Spark plug for using at tow stroke engines with thread M18. Good replacement for the original spare part (T18). The heating rate complies 260 (cold spark plug), best use for water and air cooled engines special for tuning engines. Made by NGK, Japan. Bosch Nr. M260 T1
8,64 €inclusive VAT, plus shipping costs temporary not available Art.No. 7531

Spark plug M18 - 175, ISOLATOR Detail M18 spark plug. This part is an NOS spare part with thread M18 x 1,5mm. The spanner gap is 26mm. The heat rating is cose to 175. Can be used for wather cooled two stroke engines like Wartburg, Barkas, Framo, ZW1103
12,50 €inclusive VAT, plus shipping costs temporary not available Art.No. 1192

Spark plug M18 - 225, NGK Detail Spark plug for using at tow stroke engines with thread M18. Good replacement for the original spare part (T18). The heating rate complies 225 (cold spark plug), best use for water and air cooled engines. Made by NGK, Japan. Bosch Nr. M225 T1
9,72 €inclusive VAT, plus shipping costs Delivery in 1-3 days Art.No. 7530

Spark plug M18 - 175, NGK Detail Spark plug for using at tow stroke engines with thread M18. Good replacement for the original spare part (W18). The heating rate complies 175 (warm spark plug), best use for water cooled engines. Made by NGK, Japan. Bosch Nr. M175 T1 spanner gap: SW 21
11,04 €inclusive VAT, plus shipping costs Delivery in 1-3 days Art.No. 7529

Bulbs spare kit R2 / 6V

Detail

Spare kit with different bulbs fit to voltage of 12V
content:

1x R2-lamp 45/40W with base P45t
1x spherical lamps 18W white with base Ba15s
1x tubular lamp 18W (C21W) with base SV 8,5
1x tubular lamp 5W (C5W) with base SV 8,5
1x bulb 4W (T4W) with base BA 9s
1x bulb for speedometer 0,6W with base BA 7s
1x spherical lamps 21W white with base Ba15s
1x spherical lamps 5W white with base Ba15s
1x Torpedo-fuse 8A
1x Torpedo-fuse 16A

25,77 €inclusive VAT, plus shipping costs

Delivery in 1-3 days

Art.No. 7145

Magnet, complete for starter 12V

Detail

Solenoid switch for starter for Trabant 601, Wartburg 353 and Barkas B1000.

operating voltage: 12V
spare part made EU
one piece will be needed

58,79 €inclusive VAT, plus shipping costs

Delivery in 1-3 days

Art.No. 784

Coil set complete for starter 6V Detail Coil kit complete with brushes for the starter motor with 6V electrical system. This is an new original spare part. One set will be needed.
Original spare part number: 8201.6/1-100	21,89 €inclusive VAT, plus shipping costs Delivery in 1-3 days Art.No. 7630

Magnet, complete for starter 6V Detail Magnet switch for all starter types: Trabant 500,600,601, Wartburg 311,312,313 and Barkas B1000 with 6V system. This is an NOS spare part.
Original spare part number: 8201.6/3-400/1	65,23 €inclusive VAT, plus shipping costs Delivery in 1-3 days Art.No. 780

Pole case complete for starter 6V Trabant Detail Outer case complete with field coils, filed coil set, two brushes, feeld coil retainer, connection wire for magnet switch. Can be used for starter motor Trabant with 6V electrical system. Pars is complete premounted and can be installed as it is. This is an new original spare part. Delivery without bearing bushings and mountng parts.
Original spare part number: 8201.6/3-100	65,50 €inclusive VAT, plus shipping costs Delivery in 1-3 days Art.No. 7642

Field coil 1 for starter 6V Detail Filed coil I for the starter motor with 6V electrical system. This coil have to be connectet with one end at the coil set and with the other end at the starter case. One piece will be needed This is an new original spare part.
Original spare part number: 8201.6/1-101	9,50 €inclusive VAT, plus shipping costs Delivery in 1-3 days Art.No. 7631

Field coil 2 for starter 6V Detail Filed coil II for the starter motor with 6V electrical system. This coil have to be connectet with one end at the coil set and with the other end at the starter case. One piece will be needed This is an new original spare part.
Original spare part number: 8201.6/1-102	9,50 €inclusive VAT, plus shipping costs Delivery in 1-3 days Art.No. 7632

Amature complete for starter 6V Trabant Detail Rotor shaft complete with collector ring for the starter motor Trabant with 6V electrical system. This is an new original spare part. Delivery without bearing bushings and mountng parts.
Original spare part number: 8201.6/1-210	62,20 €inclusive VAT, plus shipping costs Delivery in 1-3 days Art.No. 7628

Switch for warning flasher 6V, Original

Detail

6V version of switch for warning flasher. Original spare part.
With red round push button.
Fit to voltage of 6V.
Best use for Old and Youngtimer with 6V electrical system.

delivery without control bulb
contol bulb:Bulb 6V 1,2W
original-spare part no.: 8600.31/1

92,51 €inclusive VAT, plus shipping costs

Delivery in 1-3 days

Art.No. 86

Wire set for switch for warning flasher 6V

Detail

Cable set for the 6V version of switch for warning flasher.
Fit to voltage of 6V.
Can be used for many Old and Youngtimers.
Best use for Trabant as connecton between flasher unit, fuse box and switch.

original spare part
length about:630mm
one set will be needed

9,85 €inclusive VAT, plus shipping costs

Delivery in 1-3 days

Art.No. 7441

Knob for push switch 6 / 12V

Detail

Button insert for the push switchs.
Colour: yellow
Can be used for many Old and Youngtimers.

original spare part
delivery as an single part with snap ring

Original spare part number: 8600.33-2

0,98 €inclusive VAT, plus shipping costs

Delivery in 1-3 days

Art.No. 7960

Switch 6 / 12V

Detail

Universal useable switch.
Please choose
Can be used for many Old and Youngtimers.

original spare part
Original number: 8600.34

switch knop

17,55 €inclusive VAT, plus shipping costs

Delivery in 1-3 days

Art.No. 7451

Rubber cover for ignition key

Detail

Grip rubber for mounting at the ignition key.
This spare part is an original one.
Fit for the vehicles: Trabant, Wartburg, W50, Barkas LO, LD Multicar usw.

material: rubber, black
original spare parts
delivery as an single part

9,50 €inclusive VAT, plus shipping costs

Delivery in 1-3 days

Art.No. 8193

Delivery only at advance payment.

Spare key, copy is made from yor key number

Detail

Production of an spare key for door, ignition or fuel cap looks and so on...
You have to tell us your key number per email, fax or letter.
Keys for the vehicles: Trabant, Wartburg, W50, Barkas LO, LD Multicar usw.

delivery time about one to two weeks
all Trabant keys possible

Please write here your keynumber in:

29,75 €inclusive VAT, plus shipping costs

Delivery in 1-3 days

Art.No. 1341

Delivery only at advance payment.

Clutch set up to May 1985

Detail

clutch set for Trabant 500, 600 and 601 up to vintage may 1985 with two stroke engine consist of:

clutch
clutch disc without springs d=160 mm
fit to all Trabant 500, 600 und 601
one set will be needed
All parts are refreshed or manufactured in Germany

For more informations to this exchange part please use the Detail button.

Delivery only in exchange! Please send one clutch and clutch disc (original IFA) to our company in advance !

159,20 €inclusive VAT, plus shipping costs

Delivery in 1-3 days

Art.No. 7309

Clutch up to May 1985

Detail

Trabant pressure plate for the cluch disk D=160 mm
This type are offen used at Trabant 500, 600 and 601.
Vintage up to may 1985.

exchange part
refreshed in Germany

For more informations to this exchange part please use the Detail button.

overhauled in GermanyDelivery only in exchange! Please send in advance one clutch up to May 1985 (original IFA) to our company.

86,85 €inclusive VAT, plus shipping costs

Delivery in 1-3 days

Art.No. 7310

Protection cap for starter lite ( plastic )

Detail

Sealing cap to protect the starter wire (plus) against dust and moisture.
Fit to the vehicles: P70, Trabant, Wartburg, Multicar, Framo and Barkas.

made in Germany
one piece will be needed

6,85 €inclusive VAT, plus shipping costs

Delivery in 1-3 days

Art.No. 786

Ring eye D12mm, connection 6mm hose

Detail

Ring terminal ideal for doing byself to fix fuel hoses.
Best use for many old- and Youngtimers to make fuel pessure pipes or normal pertol connection hoses.
Can be used for banjo screws D= 12mm

Eye diameter: 12mm
diameter pipe connection: 6mm

4,85 €inclusive VAT, plus shipping costs

Delivery in 1-3 days

Art.No. 7539

Ring eye D12mm with pipe bend

Detail

Ring terminal ideal for doing byself to fix fuel hoses.
Best use for many old- and Youngtimers to make fuel pessure pipes or normal pertol connection hoses.
Can be used for banjo screws D= 12mm

Eye diameter: 12mm
diameter pipe connection: 8mm
pipe bend: 90 degree
pipe length total: 74mm

15,38 €inclusive VAT, plus shipping costs

Delivery in 1-3 days

Art.No. 7517

Ring eye D12mm, connection 8mm hose

Detail

Ring terminal ideal for doing byself to fix fuel hoses.
Best use for many old- and Youngtimers to make fuel pessure pipes or normal pertol connection hoses.
Can be used for banjo screws D= 12mm

Eye diameter: 12mm
diameter pipe connection: 8mm

5,95 €inclusive VAT, plus shipping costs

Delivery in 1-3 days

Art.No. 7540

Ring eye D10mm, connection 8mm hose

Detail

Ring terminal ideal for doing byself to fix fuel hoses.
Best use for many old- and Youngtimers to make fuel pessure pipes or normal pertol connection hoses.
Can be used for banjo screws D= 10mm

Eye diameter: 10mm
diameter pipe connection: 8mm

4,90 €inclusive VAT, plus shipping costs

Delivery in 1-3 days

Art.No. 7538

Ring eye D10mm with pipe bend

Detail

Ring terminal ideal for doing byself to fix fuel hoses.
Best use for many old- and Youngtimers to make fuel pessure pipes or normal pertol connection hoses.
Can be used for banjo screws D= 10mm

Eye diameter: 10mm
diameter pipe connection: 6mm
pipe bend: 90 degree
pipe length total: 55mm

14,99 €inclusive VAT, plus shipping costs

Delivery in 1-3 days

Art.No. 7516

Ring eye D10mm, connection 6mm hose

Detail

Ring terminal ideal for doing byself to fix fuel hoses.
Best use for many old- and Youngtimers to make fuel pessure pipes or normal pertol connection hoses.
Can be used for banjo screws D= 10mm

Eye diameter: 10mm
diameter pipe connection: 6mm

4,60 €inclusive VAT, plus shipping costs

Delivery in 1-3 days

Art.No. 7537

Windscreen washer kit 6V

Detail

Set for windscreen washer system with electrical pump and water bottle
voltage: 6V
Scope of delivery:

bottle 1,5 liter
cap
metal holder
wash pump 6V

Ideal for upgrate the mechanical hand pump into an electrical system.

56,53 €inclusive VAT, plus shipping costs

temporary not available

Art.No. 7597

Electronic ignition base plate for 6V, complete

Detail

Retrofitting kit for 6V ignition system of 2-stroke Trabant variants to change from contact breaker system to electronic system.
All mechanical parts will not changed. The centrifugal advance mechanismn will left, too. So the change of ignition timing during low revs will work also after retrofitting.
Special made for 6V system Trabant 500,600 and 601

Advantage:

no mechanical contact breakers (no maintenance work for lubricating and readjusting)
Simplified adjusting of ignition timing for cylinder 2 through automatic adoption of cylinder 2 timing
If necessary the old contact breake ignition plate can be put back later

An additional wire for power supply of ignition system is to install from ignition coil (+6V, terminal 15) to base plate.

159,50 €inclusive VAT, plus shipping costs

temporary not available

Art.No. 7536

Brush for starter

Detail

Spare-brushes of the starter engine to solder on at the coil set.
Can be used for all kind of starters 6V and 12V left- and right turning (without Trabant 1.1, Wartburg 1.3 and Baraks B1000-1)
mounting place: brushholder bas plate

size: 16X19x7
delivery as an single part
for each starter two pieces will needed

original spare part number: 8202.11-220:10

8,24 €inclusive VAT, plus shipping costs

Delivery in 1-3 days

Art.No. 785

Spring for brush starter

Detail

Pressure spring for the brushes of the starter engine.
This spring will push the brush at the collector ring from the rotor shaft.
Can be used for all kind of starters 6V and 12V left- and right turning (without Trabant 1.1, Wartburg 1.3 and Barkas B1000-1)
mounting place: brushholder bas plate

original spare part
delivery as an single part
for each starter two pieces will needed

original spare part number: 8202.11-220.6

1,55 €inclusive VAT, plus shipping costs

Delivery in 1-3 days

Art.No. 7629

Bolt for starter

Detail

Bolt of the Bearing case of the starter engine.
Connection bolt will be mounted at the beraing case threadholes and on the other side it will hold the rear case cover.
Delivery as a single part without nuts an washers.
Can be used for all kind of starters 6V and 12V left- and right turning (without Trabant 1.1, Wartburg 1.3 and Barkas B1000-1)

original spare part
surface: galvaniced
total length: 16.5 cm
delivery as an single part
for each starter two pieces will needed

original spare part number: 8202.1-000:4/1

2,93 €inclusive VAT, plus shipping costs

Delivery in 1-3 days

Art.No. 7658

Battery 6V 84Ah, dry ( not charched )

Detail

Batterie for cars with 6V supply voltage. The capacity is 84 Ah. The starting power is 240A.
We just deliver this battery dry and uncharched.
Design fit to historical vehicles.

length: 22,5 cm
wide: 17,5 cm
highness case: 20 cm
total highness inclusive pins: 22 cm
made in Germany

+7,50 Euro deposit

225,50 €inclusive VAT, plus shipping costs

Delivery in 1-3 days

Art.No. 1225

Plug for body

Detail

Small plug for holes diameter 5mm.
Can be used for the car body.

material: rubber, black
total length: 27mm
made in Germany

2,49 €inclusive VAT, plus shipping costs

Delivery in 1-3 days

Art.No. 7705

Rubber sleeve cushion for shock absorber 30mm

Detail

The bushing is pressed in to the eye of the shock absorber diameter size 30mm.
Fit to Trabant 500,600,601 leaf spring shocks or Wartburg 311/312/353, DDR trailers shocks and so on...

1x length inner sleeve: 32 mm
1x rubber
made in Germany
2 or 4 pieces will be needed

12,90 €inclusive VAT, plus shipping costs

Delivery in 1-3 days

Art.No. 8028

Electric fuel cock

Detail

Electical petrol valve (shut off vale) of the Trabant 601.
Easy to install beween the fuel hose form the petrol tank to the carburettor.

fit to all Trabant 500, 600 and 601 types
power: 12V
maximum reduction of the permanet leaking of the craburettors at stand
one piece will be needed
delivery inclusive electrical connecting cable

45,32 €inclusive VAT, plus shipping costs

Delivery in 1-3 days

Art.No. 8217

Bushing for starter motor

Detail

Busing made of braas for the starter of the Trabant 601, Wartburg 353 and Barkas B1000.
This bearing guides the armature in front and rear side.
Can be used for 6V and 12V starters.

delivery as an single part
original spear part
two pieces will be needed

5,90 €inclusive VAT, plus shipping costs

Delivery in 1-3 days

Art.No. 8440

Bulb retainer display instruments, additional negative terminal

Detail

Holder for bulbs as an new reproduction part. Can be used for nearly all IFA vehicles.
Type with two contact pins for wire plug: 6,3x0,8 (standart)
1x pin for plus terminal (+) and 1x pin for negative pin (-)
Useabe for bulbs 6V 2W or 12V 2W with Ba7S base as speedometer lightning, display and indecator lights.