Brake system

The complete offer in Brake system

Dual brake master cylinder for Multicar M24, M25 CZ type

This tandem brake master cylinder is an complete reproduction.
Version: Czech production
Used at the mini truck Multicar M25 and some types of M24.

New produced spare part
made in EU
one piece will be needed

74,26 €inclusive VAT, plus shipping costs

Delivery in 1-3 days

Art.No. 8361

Sleeve set for brake master cylinder (1-circuit) Ø 25,4mm = 1

Detail

Two sealing rings for the wheel brake cylinders built in front brake of Wartburg 311.
Case mark: Renak CH 7

for diameter of piston: 25,4 mm
scope of delivery: two piece of ring sleeve
one piece is needed for each wheel brake cylinder
first-class quality made in Germany

35,44 €inclusive VAT, plus shipping costs

temporary not available

Art.No. 7176

Sleeve kit dual brake master cylinder Ø 28mm (1,1″) , original, M25

Detail

Sleeve set to repair the dual brake master cylinder used in mini truck Multicar M25 and 2t-trailer fit to Multicar.
complete set with:

4x sealing rings with outer lip
2x flat rubber valves
2x conical rubber valves
4x copper sealing rings

made in Germany
one set will be needed

35,44 €inclusive VAT, plus shipping costs

Delivery in 1-3 days

Art.No. 7236

Dual brake master cylinder for Multicar M24, M25, 2t-trailer

Detail

This tandem brake master cylinder.
Used at the mini truck Multicar M25 and some types of M24 and 2t-trailer fit to Multicar.

Made u´in EU
one piece will be needed

122,81 €inclusive VAT, plus shipping costs

Delivery in 1-3 days

Art.No. 7633

Protection bellows for pressure bar input brake master cylinder Detail Protection bellows for the single and tandem brake master cylinders. fit ot vehicles: Framo, B1000, B1000-1, Wartburg 311, 312, 313, 353, Multicar M22, M24, M25. inner diameter conical end: 15 mm inner diameter cylindrical end: 37 mm length: 35 mm - 58 mm
9,50 €inclusive VAT, plus shipping costs Delivery in 1-3 days Art.No. 4214

Stop-lamp oil-pressure switch pin plug

Detail

Hydraulic pessure cennected switch for the brake lights.
Type of the switch with flat plug contacts.

delivery withou mounting parts, without wires or plugs
Fit to the vehicles: Mulicar M22, M24, M26

11,33 €inclusive VAT, plus shipping costs

Delivery in 1-3 days

Art.No. 8375

Cap for stop-lamp oil-pressure switch

Detail

Rubber cap for the brake ligths switch. Best protection for dust and wather.

Fit to the vehicles: Trabant 500, 600, 601, 1.1 Wartburg 311, 312, 313, 353, 1.3 Barkas B1000,B1000-1 Framo, Mulicar M22, M24, M26

7,93 €inclusive VAT, plus shipping costs

Delivery in 1-3 days

Art.No. 7308

Sleeve set dual brake master cylinder Ø 25,4mm (1″) , original, M25

Detail

Sleeve set dual brake master cylinder, Multicar M25
complete set

made in Germany
one set will be needed

35,44 €inclusive VAT, plus shipping costs

Delivery in 1-3 days

Art.No. 7187

Sleeve set dual brake master cylinder, complete, M25 Ø 25,4mm

Detail

Sleeve set dual brake master cylinder, Multicar M25
complete set

made in EU
one set will be needed

12,40 €inclusive VAT, plus shipping costs

temporary not available

Art.No. 7186

Banjo screw for wheel brake cylinders

Detail

banjo screw for mounting the aluminium thread adapter at all brake cylinders of the truck Multicar M25.

disposition:

front brake right: 2 pieces
front brake left : 2 pieces
rear brake right : 1 piece
rear brake left : 1 piece

4,44 €inclusive VAT, plus shipping costs

Delivery in 1-3 days

Art.No. 8476

Ring terminal 30 degrees for brake pipe / clutch

Detail

Ring terminal, mounting one hand with banjo screw M12 and on the other end by brake pipe or brake hose (M12x1)

technical specifications:

material: Aluminium
bore size for banjo screw: 12,1mm, thickness: 11,2mm
thread: M12x1 Type E
delivery without mounting bits

11,30 €inclusive VAT, plus shipping costs

Delivery in 1-3 days

Art.No. 8602

Front brake system for Multicar M25

Wheel brake cylinder front, fit to Multicar M25, overhauled

Detail

In germany refreshed brake cylinder can be used for the front wheel brake system of the Multicar type M25.
The wheel brake cylinders fit to the brakes of the right and left front axle.

delivery as an single part inclusive bleeder screw
overhauled in Germany
for one vehicle four pieces will be needed

Please note: Only direct exchenge possible.Please send your old overhaulable brake cylinder LZ65 to our company in advance !

36,06 €inclusive VAT, plus shipping costs

Delivery in 1-3 days

Art.No. 7773

Wheel brake cylinder front, fit to Multicar M25

Detail

Brake cylinder can be used for the front wheel brake system of the Multicar type M25.
The wheel brake cylinders fit to the brakes of the right and left front axle.

delivery as an single part inclusive bleeder screw
made in EU
for one vehicle four pieces will be needed

36,81 €inclusive VAT, plus shipping costs

Delivery in 1-3 days

Art.No. 7585

Bleeder screw for frontwheel brake cylinder

Detail

Bleeder screw for the front brake cylinders of the truck Multicar M25.

thread: M8x1,25
spanner gap: SW9
total length: 49 mm
thread length: 15 mm
length of the spanner gap: 7,6 mm
one piece will be needed for each wheel brake cylinder

5,55 €inclusive VAT, plus shipping costs

Delivery in 1-3 days

Art.No. 7775

Delivery only at advance payment.

Brake hose front axle for Multicar

Detail

Wheel brake hose for the front brake system of the Multicar type M22, M24, M25 (not useable for M25 4WD).
Connection hose between the brake pipe and the wheel brake cylinder front right or left axle side.

total lenght: 51cm
thread: 1x M12 x 1,5 core thread
1x M12 x 1,5 male thread
delivery as an single part
made in EU
for one vehicle two pieces will be needed

14,51 €inclusive VAT, plus shipping costs

Delivery in 1-3 days

Art.No. 7518

Brake hose front axle for Multicar 4WD

Detail

Wheel brake hose for the front brake system of the Multicar type M24, M25 four wheel drive.
Connection hose between the brake pipe and the wheel brake cylinder front right or left axle side.

total lenght: 51cm
thread: 2x M12 x 1,5 core thread (female)
delivery as an single part
made in EU
for one vehicle two pieces will be needed

14,51 €inclusive VAT, plus shipping costs

Delivery in 1-3 days

Art.No. 8083

Brake line front, fit to Multicar M25 4WD

Detail

Brake pipe made of NiCu form the front wheel brake cylinder to the brake hose.
Can be used for the front wheel brake system of the Multicar type M25wit VW engine and four wheel drive.

delivery complete with nuts M12x1
made in Germany
for one vehicle four pieces will be needed

19,20 €inclusive VAT, plus shipping costs

Delivery in 1-3 days

Art.No. 7814

Rear brake system for Multicar M25

Wheel brake cylinder rear, fit to Multicar M25

Detail

Reproducted brake cylinder can be used for the rear wheel brake system of the Multicar type M25.
The wheel brake cylinders fit to the brakes of the right and left rear axle.

delivery as an single part
made in EU
for one vehicle four pieces will be needed

32,08 €inclusive VAT, plus shipping costs

Delivery in 1-3 days

Art.No. 7586

Brake hose rear, fit to Multicar

Detail

Wheel brake hose for the rear brake system of the Multicar type M22, M24, M25.
Connection hose between the brake pipe and the wheel brake cylinder rear axle.

total lenght: 51cm
thread: M12x1, both ends as male type
delivery as an single part
made in EU
for one vehicle two pieces will be needed

13,30 €inclusive VAT, plus shipping costs

Delivery in 1-3 days

Art.No. 7641

Bleeder screw for rear wheel brake cylinder

Detail

Bleeder screw for the aluminium thread adpater of rear axle brake system of the truck Multicar M25.

thread: M8x1,25
spanner gap: SW9
total length: 32 mm
thread length: 11 mm
length of the spanner gap: 5 mm
one piece will be needed for each side of rear axle

3,22 €inclusive VAT, plus shipping costs

Delivery in 1-3 days

Art.No. 8475

Bleeder screw for rear wheel brake cylinder

Detail

Bleeder screw for the rear brake cylinders of the truck Multicar M25.

thread: M10x1
spanner gap: SW11
total length: 35,5 mm
thread length: 12 mm
length of the spanner gap: 5,3 mm
one piece will be needed for each wheel brake cylinder

3,95 €inclusive VAT, plus shipping costs

Delivery in 1-3 days

Art.No. 8054

Hand brake cable for Multicar M25

Detail

This brake wire fit to Multicar type M25.
New reproduction made in EU

length total: 87cm
length of bowden wire: 54cm
two pieces will be needed

25,50 €inclusive VAT, plus shipping costs

Delivery in 1-3 days

Art.No. 8362

Brake leaver kit for Multicar M25

Detail

One kit of hand cable levers for the rear brake shoes of the Multicar type M25 without 4 wheel drive.
Set consist of:

1x brake leaver, left hand
1x brake leaver, right hand
2x mounting rivet
made in EU
one set will be needed

14,88 €inclusive VAT, plus shipping costs

Delivery in 1-3 days

Art.No. 8472

Brake shoe set for Multicar M25 with brake leaver

Detail

The brake shoes kit fit to the rear axle of the Multicar type M25 without 4 wheel drive.
Two brake shoes got mounted leaver for the handbrake cable.
Set consist of:

4 pieces of breake shoe with long lining
2x mounted leaver
made in EU
one set will be needed

58,90 €inclusive VAT, plus shipping costs

Delivery in 1-3 days

Art.No. 8467

Brake shoe set for Multicar M25

Detail

The brake shoes kit fit to the frontaxle and to the rear axle of the Multicar type M25 without 4 wheel drive.
Set consist of:

4 pieces of breake shoe with long lining
made in EU
for each axle, one set will be needed

52,06 €inclusive VAT, plus shipping costs

Delivery in 1-3 days

Art.No. 7096

Brake shoe set front axle Multicar M25 4WD

Detail

The brake shoes are complete overhauled in Germany
Fit to the front axleof the Multicar type M25 with 4 wheel drive.
Set consist of:

4 pieces of breake shoe with long lining
made in Germany

Please note: the old breake shoes have to be shiped to our compaly in advance.

only exchenge part !

244,76 €inclusive VAT, plus shipping costs

Delivery in 1-3 days

Art.No. 7800

Brake drum for Multicar M25

Detail

Brake drum as an single part fit to the front wheel and rear wheel brakes for Multicar type M25.

delivery as an single part
four pieces will be needed
made in EU

64,26 €inclusive VAT, plus shipping costs

Delivery in 1-3 days

Art.No. 7881

Brake pressure regulatoring valve, complete LAD28 for M25

Detail

Brake pressure regulatoring valve to level the right brake perssure at the rear axle depends on the loades weight.
Fit for Multicar M25.
mounting place: between brake pipe and wye junction rear axle.

1x brake pipe connection top end M12x1
1x brake pipe connection side end M12x1
new reproduction
one piece will be needed

additional needed special tools for deassembly / assembly:
no special tools needed

56,88 €inclusive VAT, plus shipping costs

Delivery in 1-3 days

Art.No. 8360

pipe-connector

Detail

Brake tube merger for the connection of two brake tubes with flange type E and thread M12x1mm

material: steel, galvanized
thread: M12 X 1
lenght: 29mm
made in Germany

6,60 €inclusive VAT, plus shipping costs

Delivery in 1-3 days

Art.No. 7275

Universal brake line, PVC-coated per 1 m , 6 x 0,7 mm Brakepipeline 6mm x 0,7mm for Barkas B1000 price per meter. max. lenght per piece: 5m
3,55 €inclusive VAT, plus shipping costs Delivery in 1-3 days Art.No. 6038

Universal brake line 6x0,7 5m

Detail

Zinced and PVC-plated steel brake line.
Scope of delivery 5 meters.
The pipe can be bent by hand with normal pressure. For the flange on the end of the tubes it will be necessary to use an professional tube border tool.

outside diameter: 6mm
thickness: 0,7mm
length: 5m
made in Germany

price per meter: 3,24 €

17,82 €inclusive VAT, plus shipping costs

Delivery in 1-3 days

Art.No. 6039

Holder for brake hose

Detail

Brake hose retainer for Multicar M22, M24, M25

to put into the circumferential slot of the brake hose fitting
slot wide: 14 mm
thickness: 1,75 mm

5,97 €inclusive VAT, plus shipping costs

Delivery in 1-3 days

Art.No. 6037

Universal brake line, CUNIFER 5m, 6mm Detail Brakepipeline 6 x 0,7 mm made of NiCuFe length: 5m for B1000, B1000-1, Mulicar M22, M24, M26, Framo, Warburg 311 and 313
price for each meter: 8,60 €/m	42,99 €inclusive VAT, plus shipping costs Delivery in 1-3 days Art.No. 7398

Ring sleeve, for wheel brake cylinder, front, original

Detail

Sealing kit for repairing of the original IFA-BHL front wheel brake cylinder of the Multicar M25.
Best quality made in Germany.
The set included 2 pieces of ring sealings and two pieces of O-sealings.

Total four sets will be needed
made in Germany
fit for all types of M25: Cunewald engine, VW engine and four wheel drive

The ring sleeve should only be changed, if inner surface of cylinder is okay.
Otherwise the complete wheel brake cylinder should be changed.

18,50 €inclusive VAT, plus shipping costs

temporary not available

Art.No. 7768

Screw-cap for brakeline 6 x 0,7

Detail

Screw-cap for brakeline 6mm x 0,7mm. The screws can be mounted at steel or nickel-copper brake lines.
Please count how much pieces zou need total.
Fit to Barkas B1000, Multicar M22, M24, M25 and all vehicles with 6mm brake line.

border: type E
thread: M12x1
material: steel, galvaniced
made in Germany

1,80 €inclusive VAT, plus shipping costs

Delivery in 1-3 days

Art.No. 7276

Delivery only at advance payment.