clutch system

The product category Wartburg 353 > Spare parts > Engine > clutch is spread over 3 sites:

Spring for clutch release bearing up to 6/85

Snap clamp for mounting the pressure bearing at the release shaft.
Type: old version of pressure bearing.
This part is an new reproduction made in Germany. Best replacement for the original ones.
Clip is made of spring steel.
Two pieces will be needed.
Surcace: blank.
Fit to the following car types:

Wartburg 353 up to 6-1985 Limousine and Tourist
Barkas B1000 up tp 3-85 with clutch D=180mm
Multicar M22
two pieces will be needed

normaly 2,99 € now 2,19 €inclusive VAT, plus shipping costs

Delivery in 1-3 days

Art.No. 7956

Spring for clutch release bearing from 6/85

Detail

Snap clamp for mounting the pressure bearing at the release shaft.
Fir to the following car types:
Wartburg 353 ab 6-1985 Limousine and Tourist
Trabant 1,1 without vintage limit Kombi and Limousine
Wartburg 1,3 without vintage limit Tourist and Limousine
Barkas B1000 ab 3-85 with clutch D=200mm
Barkas B1000-1 without vintage limit

2,49 €inclusive VAT, plus shipping costs

Delivery in 1-3 days

Art.No. 7328

Cluch cable complete original

Detail

Bowdencable with grease nipple for the Wartburg 353 cluch. Fit to all models.

total length: 55 cm
lenght of the cover: 30 cm
original spare part

85,20 €inclusive VAT, plus shipping costs

temporary not available

Art.No. 8068

Cluch cable complete

Detail

Bowdencable without grease nipple for the Wartburg 353 cluch. Fit to all models.

total length: 55 cm
lenght of the cover: 29 cm
made in EU

36,21 €inclusive VAT, plus shipping costs

Delivery in 1-3 days

Art.No. 3110

Retainer spring for clutch cable

Detail

Retainer wire to fic the clutch cable at the vehicle frame or holder.
Can be used for Fahrzeuge: Wartburg 311,312, 313, Wartburg 353 and 1.3 and Barkas B1000 und B1000-1.
High quality reproduction.

material: spring steel
one piece will be needed

3,90 €inclusive VAT, plus shipping costs

Delivery in 1-3 days

Art.No. 8313

Spring for clutch pedal

Detail

Release spring for the pedal system at the Wartburg 353 and Wartburg 1,3.
Will be mounted on one hand at the clutch pedal and on the other side at the car body.
The spring supports the pedal reset of the clutch pedal.

material: steel
surface: galvaniced
one piece will be needed
delivery as an single part
best replacement and high quality, made in Germany

4,90 €inclusive VAT, plus shipping costs

Delivery in 1-3 days

Art.No. 8209

sleeve for cluch cable

Detail

sleeve for clutch cable of Wartburg 353 (2-stroke) and Wartburg 1.3 (4-stroke)

length: 90mm
lenght (short): ca. 55mm
inner diameter big: 12mm
inner diameter small: ca. 6mm

Subject to availability (no regular range)!

8,80 €inclusive VAT, plus shipping costs

Lieferbar innerhalb von 6-8 Wochen.

Art.No. 6370

Rivet set for clutch facing ( 12 pices )

Detail

Tubular rivet for cluch facing. Like the original ones made of steel.
Fit to the clutch linings of:

Trabant 601 D=160mm old- (fixede) and late- (tongued) clutch disc
Trabant1.1 clutch disc
Wartburg 353 D=180mm clutch disc
Barkas B1000 D=180mm and 200mm clutch disc
Wartburg 1.3 clutch disc
Barkas B1000-1 clutch disc

ideal for self repair
scope of delivery 12 pieces
material: steel
made in Germany

4,64 €inclusive VAT, plus shipping costs

Delivery in 1-3 days

Art.No. 664

Brake pipe spanner 10-11mm angled Detail Special tool for mounting or demounting of screw-cap for brakelines. type: level angleded Fit to brake screws SW10 and SW11.
12,47 €inclusive VAT, plus shipping costs Delivery in 1-3 days Art.No. 7702

The product category Wartburg 353 > Spare parts > Engine > clutch is spread over 3 sites:

1 2 3
Show all products

* All prices inclusive VAT and plus shipping costs.