Fuel system

The complete offer in Fuel system

Fuel pump and bits

Spare kit for fuel pump

fuel pump spare kit constist of:
1 x membran; 1 x pressure spring, 2 x valves, 1 x strainer, 2 x seal,
1 sealing ring (rubber)

fit for all fuel pumps Wartburg 353 and B1000

24,45 €inclusive VAT, plus shipping costs

Delivery in 1-3 days

Art.No. 3142

Insulation piece for fuel pump

Detail

insulation plate for flange of fuel pump
This insulation plate reduced the factor of heat from engine block to the fuel pump. It protects from blowholes when the fuel evaporates because of to much heat.

one piece will be needed for each fuel pump
it will mounted between two flange rubber seals
made of plastic
fit for all fuel pumps Wartburg 353 and B1000

8,55 €inclusive VAT, plus shipping costs

temporary not available

Art.No. 6766

Flange seal for fuel pump

Detail

Rubber seal for flange of fuel pump.
New German reproduction. Material textil rubber, fuel resitant.

two pieces will be needed for each fuel pump ( one between engine block and insulation piece and another one between insulation piece and fuel pump
fit for all fuel pumps Wartburg 353 and B1000
made in Germany

6,75 €inclusive VAT, plus shipping costs

Delivery in 1-3 days

Art.No. 6765

Fuel pump

Detail

The diaphragm fuel pump is mounted direct at the engine. Fit for Wartburg 353 and Barkas B1000 (2-stroke engine)
The petrol pump will be delivered as complete unit.

Reproduction in Europe
delivery without Sealing
one piece will be needed

49,97 €inclusive VAT, plus shipping costs

Delivery in 1-3 days

Art.No. 3140

Transmitter for fuel gauge bus

Detail

Sensor for fuel gauge with potentiometer for connection to all offert fuel gauges.
mounting place: on top / inside of the fuel tank.
Fit to all Barkas B1000 and B1000-1 models of Bus
Scope of delivery complete with rubber sealing and float.

made in Germany
one piece will be needed

75,11 €inclusive VAT, plus shipping costs

temporary not available

Art.No. 7467

Transmitter for fuel gauge Pick up

Detail

Sensor for fuel gauge with potentiometer for connection to all offert fuel gauges.
mounting place: on top / inside of the fuel tank.
Fit to all Barkas B1000 and B1000-1 models of Pick up
Scope of delivery complete with rubber sealing and float.

made in Germany
one piece will be needed

49,20 €inclusive VAT, plus shipping costs

temporary not available

Art.No. 7459

Sealing for transmitter fuel gauge

Detail

Rubber seal for the sensor of the fuel gauge as an single part.
Fit to all vehicle models: Trabant 601, Trabant 1.1, Wartburg 353, Wartburg 1.3, Brakas B1000, Barkas B1000-1, Multicar.

material: fuel resistant rubber, colour: black
made in Germany
one piece will be needed

4,85 €inclusive VAT, plus shipping costs

Delivery in 1-3 days

Art.No. 7461

Float for transmitter fuel gauge

Detail

Plastic float for the sensor of the fuel gauge as an single part.
Fit to all vehicle models: Trabant 601, Trabant 1.1, Wartburg 353, Wartburg 1.3, Brakas B1000, Barkas B1000-1, Multicar.

material: fuel resistant plastic, colour: withe
made in Germany
one piece will be needed

25,90 €inclusive VAT, plus shipping costs

temporary not available

Art.No. 7460

Sensor for KMVA (display for fuel consumption) Detail KMVA sensor for Wartburg 353 original made Germany by IFA
59,69 €inclusive VAT, plus shipping costs temporary not available Art.No. 6178

float gauge for carburettor (new type) Jijkov Detail carburettor float gauge for carburettor of Wartburg 353, B1000 called Jijkov made of plastic only few pieces available (originale spare part)
56,90 €inclusive VAT, plus shipping costs Delivery in 1-3 days Art.No. 6622

float gauge for carburettor (old type) 40 F Detail carburettor float gauge for old type of carburettor of Wartburg 353, B1000 and Robur (LO) called 40 F Reproduction made in EU
29,56 €inclusive VAT, plus shipping costs Delivery in 1-3 days Art.No. 6517

Pin for float gauge carburettor 40 F

Detail

Steel pin for the carburettor float gauge.
Fit for BVF carburettors type 40F of Wartburg 353, B1000 and Robur (LO).

delivery as single part
made in Germany
one piece will be needed

2,25 €inclusive VAT, plus shipping costs

Delivery in 1-3 days

Art.No. 8582

Seal for carburettor case 40 F, made in Germany Detail Sealing for the both housings (float case) of old type of carburettor type BVF 40F. This sealing is made in Germany of special fuel resistant sealing paper. The holes and sizes are exactly and conforms to the original spare part. Fit to the Berliner carburettors for Wartburg 353 (40F 2-11) and Barkas B1000 40F 1-12.
8,95 €inclusive VAT, plus shipping costs Delivery in 1-3 days Art.No. 7799

Paper seal for flange throttle valve (carburettor 40 F)

Detail

Sealing for flange throttle valve of old type of carburettor of Wartburg 353 and B1000, called BVF 40 F.
High quality made in Germay. Made of fuel resistant sealing paper.

two pieces needed for one carburettor
mounted between flange throttle valve (carburettor 40 F) and cover of carburettor (drainer)
between cover of carburettor (drainer) and intake manifold
fit for Wartburg 353 und B1000

3,74 €inclusive VAT, plus shipping costs

Delivery in 1-3 days

Art.No. 6485

Rubber seal for flange throttle valve (carburettor 40 F)

Detail

Rubber sealing for flange throttle valve of old type of carburettor of Wartburg 353 and B1000, called BVF 40 F.
High quality made in Germay. Made of fuel resistant rubber.

one pieces needed for one carburettor
mounted between flange throttle valve (carburettor 40 F) and carburettor case
fit for Wartburg 353 und B1000
thickness: 1mm

4,95 €inclusive VAT, plus shipping costs

Delivery in 1-3 days

Art.No. 6486

Seal for carburettor case (old type) 40 F Detail Simple paper sealing with small divergences at the accuracy of fit. Cheaper product, made in Europe. seal for housing of old type of carburettor of Wartburg 353 and B1000, called 40-F
2,90 €inclusive VAT, plus shipping costs Delivery in 1-3 days Art.No. 6478

Mixture screw BVF 40F

Detail

CO idling mixture screw of the carburettor type VF 40F 2-11 and 40F 1-12.

delivery as single part (without sealing ring)
fit for the vehicles Wartburg 353 and Barkas B1000
material: spezial heat and fuel restistant rubber
one piece will be needed

9,90 €inclusive VAT, plus shipping costs

Delivery in 1-3 days

Art.No. 8541

O-ring-sealing for mixture screw BVF 40F

Detail

Rubber O-ring sealing for the small mixture screw of the carburettor type BVF 40F 2-11 und 40F 1-12.

fit for the vehicles Wartburg 353 and Barkas B1000
material: spezial heat and fuel restistant rubber
one piece will be needed

0,89 €inclusive VAT, plus shipping costs

Delivery in 1-3 days

Art.No. 8301

Sealing ring carburettor slide jet 8 x 11 x 1,0

Detail

Special made fiber sealing as single part for sealing the brass air adjustment slide jet to the carburettor and the cover of the main jet.
This sealing rings are made for the exact fitting and sealing of this components.
Useable for the carburettor types: BVF 40F 2-11 of the car Wartburg 353 and carburettor types: BVF 40F 2-11 of the car Barkas B1000.
size:

inside diameter: 8,2mm
outside diameter: 11mm
thickness: 1,0mm
two pieces will be needed

1,85 €inclusive VAT, plus shipping costs

Delivery in 1-3 days

Art.No. 8300

Nozzle holder carburettor slide jet

Detail

Nozzle retainer for the slide jet carburettor.
This part ist new producted in Germany (exact fitting).
Useable for the carburettor types: BVF 40F 2-11 of the car Wartburg 353 and carburettor types: BVF 40F 2-11 of the car Barkas B1000.

delivery as single part
material: brass
made in Germany
one piece will be needed

9,84 €inclusive VAT, plus shipping costs

Delivery in 1-3 days

Art.No. 8536

Sealing plug for carburettor slide jet

Detail

New producted sealing screw as single part for sealing the slide jet at the carburettor.
Useable for the carburettor types: BVF 40F 2-11 of the car Wartburg 353 and carburettor types: BVF 40F 2-11 of the car Barkas B1000.

material: steel
surface: galvaniced
spanner gap: SW11
made in Germany
1 or 2 pieces will be needed, depends on the carburettor type

5,21 €inclusive VAT, plus shipping costs

Delivery in 1-3 days

Art.No. 8537

Sealing carburettor jet sprayer

Detail

Special made paper sealing as single part for sealing the jet sprayer cannel at the carburettor case and sprayer.
This sealings are made for the exact fitting and sealing of this components.
Useable for the carburettor types: BVF 40F 2-11 of the car Wartburg 353 and carburettor types: BVF 40F 2-11 of the car Barkas B1000.

material: sealing paper
made in Germany
one piece will be needed

2,80 €inclusive VAT, plus shipping costs

Delivery in 1-3 days

Art.No. 8304

Screw carburettor jet sprayer

Detail

Mounting bolt as single part for installing the jet sprayer at the carburettor case.
Useable for the carburettor types: BVF 40F 2-11 of the car Wartburg 353 and carburettor types: BVF 40F 2-11 of the car Barkas B1000.

material: steel
one piece will be needed

1,20 €inclusive VAT, plus shipping costs

Delivery in 1-3 days

Art.No. 8449

Sealing set Carburettor BVF 40F

Detail

Paper sealing kit for carburettor type BVF 40F, Wartburg 353 and Barkas B1000 and some boat engines with this carburettor type.
Best use to refresh the carburettor. All parts are made from the orignial patterns and our own quality grade.
Set consist of:

one set will be needed
material: sealing paper, Vulkanfieber, fuel resistant rubber
high quality made in Germany

20,75 €inclusive VAT, plus shipping costs

Delivery in 1-3 days

Art.No. 8305

Carburettor idler air jet BVF 40F (M6-150)

Detail

Nozzle as idling air jet for the Wartburg 353 and Barkas B1000 carburettor called Berliner Vergaser-40F
This nozzle is mountet inside of the Carburettor case. For dismounting and mounting is it necessitating to split the carurettor case.
Exact mounting place: please click on Detail

Jet size: 150
Jet thread: M6
delivery as single part

4,55 €inclusive VAT, plus shipping costs

Delivery in 1-3 days

Art.No. 8405

Carburettor main jet BVF 40F (M5-125)

Detail

Nozzle as main jet for the Wartburg 353 and Barkas B1000 carburettor called Berliner Vergaser-40F
This nozzle is mountet inside of the Carburettor case (float chamber). For dismounting and mounting is is necessitating to split the carurettor case.
Exact mounting place: please click on Detail

Jet size: 125
Jet thread: M5
delivery as single part

3,59 €inclusive VAT, plus shipping costs

Delivery in 1-3 days

Art.No. 8406

Carburettor idler jet BVF 40F (M5-75)

Detail

New produced Nozzle, made in Germany !
Nozzle as idling jet for the Wartburg 353 and Barkas B1000 carburettor called Berliner Vergaser-40F
This nozzle is mountet at the side of the Carburettor case. For dismounting and mounting is it necessitating to remove an SW11 plug. (use for mounting an new sealing LDM-part-no.:8300)
Please note: standard Wartburg is nozzle size: 75
For Barkas the nozzles are variegating form 75,80,85,90. Please check before whitch size is mounted at your carburettor.
Exact mounting place: please click on Detail

Jet size: 75
Jet thread: M5
delivery as single part

5,62 €inclusive VAT, plus shipping costs

Delivery in 1-3 days

Art.No. 8407

Carburettor idler jet BVF 40F (M5-80)

Detail

Nozzle as idling jet for the Wartburg 353 and Barkas B1000 carburettor called Berliner Vergaser-40F
This nozzle is mountet at the side of the Carburettor case. For dismounting and mounting is it necessitating to remove an SW11 plug. (use for mounting an new sealing LDM-part-no.:8300)
Please note: standard Wartburg is nozzle size: 75
For Barkas the nozzles are variegating form 75,80,85,90. Please check before whitch size is mounted at your carburettor.
Exact mounting place: please click on Detail

Jet size: 80
Jet thread: M5
delivery as single part

3,75 €inclusive VAT, plus shipping costs

Delivery in 1-3 days

Art.No. 8408

Carburettor idler jet BVF 40F (M5-85)

Detail

Jet size: 85
Jet thread: M5
delivery as single part

3,75 €inclusive VAT, plus shipping costs

Delivery in 1-3 days

Art.No. 8409

Carburettor idler jet BVF 40F (M5-90)

Detail

Jet size: 90
Jet thread: M5
delivery as single part

3,75 €inclusive VAT, plus shipping costs

Delivery in 1-3 days

Art.No. 8410

Self-repair-set carburettor 40F

Detail

6-part jet set for the carburettor BVF 40F of Wartburg 353, B1000.
Called Berliner-carburettor 40F
Delivery inclusive gauge needle valve and Mixture screw BVF 40F.

Material: brass / rubber
one set will be needed
made in Germany / EU

19,90 €inclusive VAT, plus shipping costs

Delivery in 1-3 days

Art.No. 6985

Mounting bolt for throttle valve

Detail

Screw for fix the butterfly valve at the throttle shaft.
Fit for the Berlin carburettor BVF 40F.
Please note: this screw have to be mounted properly, use Threadlocking - medium strength (Art.-Nr.:6380).
Lose screws can cause worse engine damages!

Raised countersunk-head screw
delivery as single part
total: 2 pieces will be needed

0,55 €inclusive VAT, plus shipping costs

Delivery in 1-3 days

Art.No. 8411

Hose kit for carburettor 40 F

Detail

Connection hose for the idle system of the carburettor type BVF 40F called Berliner Carburettor
Fit to Wartburg 353, B1000.

Delivery inclusive two hose clamps
Made in Germany
one kit will be needed

5,77 €inclusive VAT, plus shipping costs

Delivery in 1-3 days

Art.No. 8419

Spring for idle screw, carburettor

Detail

Pressur spring for idle adjusting screw at the carburettor.
Fit for:

Straitdraft carburetor H 362- : Wartburg 311, 312 and 313
Straitdraft carburetor H 362- : Framo V901
Straitdraft carburetor H 362- : fire fighter pump TS8
Straitdraft carburetor : P70, F8
Downdraught carburettor BVF36F: Robur LO, Wartburg 353
Downdraught carburettor BVF40F: Wartburg 353, Barkas B1000
Block carburettor 28HB: Trabant 500,600 and 601

delivery as single part
surface: galvaniced
made in Germany
one piece will be needed

1,49 €inclusive VAT, plus shipping costs

Delivery in 1-3 days

Art.No. 8459

Spring accelerator pump for carburettor (old type) 40 F

Detail

Pessure spring for the aditional accelerator pump of the carburettor type BVF 40F. Fit for Wartburg 353 and B1000.
For dismounting and mounting is it necessitating to split the carurettor case.
Exact mounting place: please click on Detail

Reproduction made in Germany
surface: galvaniced
one piece will be needed

3,88 €inclusive VAT, plus shipping costs

Delivery in 1-3 days

Art.No. 8468

Mounting nut for accelerating pump

Detail

Nut and secure washer for fix the tappet of the accelerating pump.
Fit for the Berlin carburettor BVF 40F.
For dismounting and mounting is it necessitating to split the carurettor case.
Exact mounting place: please click on Detail

scope of delivery: 1x nut and 1x spring washer
total: one pieces will be needed

0,25 €inclusive VAT, plus shipping costs

Delivery in 1-3 days

Art.No. 8442

Seal for flange suction pipe - engine block

Detail

Paper seal for flange of the inlet manifold of the carburettor type BVF 40 F, Jijkov and 36F. Mounted:

between flange inlet manifold and engine mount
one pieces needed
fit for Wartburg 353, B1000 and Wartburg 312

7,50 €inclusive VAT, plus shipping costs

Delivery in 1-3 days

Art.No. 6897

Mounting bolt for inlet pipe

Detail

Bolt for flange of the inlet pipe to the connection to the engine.
Fit to flange with the Berlin carburettor or the Jijkov-carburettor.

hexagon socket screw M8 x 16mm
strength class: 8.8
with external teeth lock washer
galvaniced
total: 8 pieces will be needed

0,55 €inclusive VAT, plus shipping costs

Delivery in 1-3 days

Art.No. 6880

Self-repair-set carburettor Jijkov Detail 10-part jet set for the carburettor of Wartburg 353, B1000 called Jijkov delivery inclusive gauge needle valve
38,24 €inclusive VAT, plus shipping costs Delivery in 1-3 days Art.No. 6984

Choke bowden cable Barkas B1000

Detail

Choke bowden wire for the Barkas B1000 two stroke.
Made in EU.

total length: 1720mm
length wire hull: 1650mm

33,32 €inclusive VAT, plus shipping costs

Delivery in 1-3 days

Art.No. 6866

Reinforcement bushing for fuel pipe 8 x 1 Detail reinforcement bushing for our polyamide fuel pipe 8 x 1 (Art.No.: 6032 and 6033) material: brass It should be uesed for every connection between polyamid fuel pipe and fuel hose! mor informations: see details
0,27 €inclusive VAT, plus shipping costs Delivery in 1-3 days Art.No. 6305

Reinforcement bushing for fuel pipe6 x 1 Detail reinforcement bushing for our polyamide fuel pipe 8 x 1 (Art.No.: 7513 and 7514) material: brass It should be uesed for every connection between polyamid fuel pipe and fuel hose! mor informations: see details
0,27 €inclusive VAT, plus shipping costs Delivery in 1-3 days Art.No. 7515

Polyamid fuel line 8 x 1

Detail

Fuel line 8 x 1 mm
material: polyamide
PA 12 HIPHL-sw according to DIN 73378 and DIN 74324
soft, heat aging and light stabilized

outer diameter:	8 mm
inner diameter:	6 mm
wall thickness:	1 mm

price is for one meter (max. 20 meter in one piece)

special advantages:
Minimal flow resistance through smooth inner walls, mechanical resistance against abrasion, impackt shock and oscilations, small bending radius, easy installation, minimal weight, no anti-corrosive necessary.

price per meter: 3,80 Euro

19,00 €inclusive VAT, plus shipping costs

Delivery in 1-3 days

Art.No. 6032

Polyamid fuel line 6 x 1

Detail

Fuel line 6 x 1 mm, most vehicles used as rear flow pipe for the petrol pump.
material: polyamide
PA 12 HIPHL-sw according to DIN 73378 and DIN 74324
soft, heat aging and light stabilized

outer diameter:	6 mm
inner diameter:	4 mm
wall thickness:	1 mm

price per meter: 3,20 Euro

16,00 €inclusive VAT, plus shipping costs

Delivery in 1-3 days

Art.No. 7514

Polyamid fuel pipe 8 x 1, price per meter

Detail

Fuel line 8 x 1 mm
material: polyamide
PA 12 HIPHL-sw according to DIN 73378 and DIN 74324
soft, heat aging and light stabilized

outer diameter:	8 mm
inner diameter:	6 mm
wall thickness:	1 mm

price 4,80 Euro / meter

4,80 €inclusive VAT, plus shipping costs

Delivery in 1-3 days

Art.No. 6033

Polyamid fuel pipe 6 x 1, price per meter

Detail

Fuel line 6 x 1 mm, most vehicles used as rear flow pipe for the petrol pump.
material: polyamide
PA 12 HIPHL-sw according to DIN 73378 and DIN 74324
soft, heat aging and light stabilized

outer diameter:	6 mm
inner diameter:	4 mm
wall thickness:	1 mm

Bitte beachten: abgelängte Ware auf Kundenwunsch, keine Rücknahme oder Umtausch!

4,50 €inclusive VAT, plus shipping costs

Delivery in 1-3 days

Art.No. 7513

Hose clip 8 - 12 / 7,5 stainless steel

Detail

Clip made of stainless steel for fuel hosed from diameter 8mm up to 12mm.
The wide of the clip is 7,5mm.

3,85 €inclusive VAT, plus shipping costs

Delivery in 1-3 days

Art.No. 6034

Hose clip 12 - 20 / 9

Detail

for fuel hose from D= 12mm up to 20mm.
the wide of the clip is 9mm.

1,30 €inclusive VAT, plus shipping costs

Delivery in 1-3 days

Art.No. 6036

1+2

Petrol filter universal

Detail

Gasoline filter for the universal duty.
The filter will be mounted between the fuel line.

connection diameter: 6 and 8mm
material: petrol resistant plastic with parer filter
price per piece

3,90 €inclusive VAT, plus shipping costs

Delivery in 1-3 days

Art.No. 7224

fuel pipe-return, 6mm, copper pipe

Detail

Copper tube to use as fuel pipe to connect the fuel pump and the fuel tank. (return flow line)

material: copper tube
size: 6x1
length: 5 meter
one piece will be needed

price per meter: 7,96 Euro

39,79 €inclusive VAT, plus shipping costs

Delivery in 1-3 days

Art.No. 727

Fuel pipe 8mm, copper pipe

Detail

Copper tube to use as fuel pipe to connect the fuel tank and the fuel pump. (suction line)

material: copper tube
size: 8x1
length: 5 meter
one piece will be needed

Preis pro Meter: 10,91 Euro

54,51 €inclusive VAT, plus shipping costs

Delivery in 1-3 days

Art.No. 726

Texture-fuel hose 6mm and clamps

Fuel hose, 5,5 mm with texture

Detail

Flexible fuel hose with outside texture. Best use for the fexible connection between fuel tank an carburettor or between metal / polyamid pipes and components like: tank, carburettor, fuel filter, fuel pump...
Delivery as single part without mounting bits.
The price is for each 1m lenght.
If you order for example 3x 1m so you will get one piece with 3m length and so on.

inside diameter: 5,5mm
material: petrol resistant rubber with outside texture
made in Germany

priece per Meter: 5,14 Euro

5,14 €inclusive VAT, plus shipping costs

Delivery in 1-3 days

Art.No. 728

Hose clip for fuel hose 5,5 mm with texture

Detail

Clamp for flexible fuel hose (5,5mm inside diameter) with outside texture. Best use for the fexible connection between fuel tank an carburettor or between metal / polyamid pipes and components like: tank, carburettor, fuel filter, fuel pump...
Delivery as single part.
Please note: in application with polyamid pipes you have to insert an metal bushing in advance!

max.diameter: 11mm
wide: 9mm
re-usable

1,47 €inclusive VAT, plus shipping costs

Delivery in 1-3 days

Art.No. 6197

Hose clip for fuel hose, 8 mm with texture

Detail

Clamp fpr flexible fuel hose (5,5mm inside diameter) with outside texture. Best use for the fexible connection between fuel tank an carburettor or between metal / polyamid pipes and components like: tank, carburettor, fuel filter, fuel pump...
Delivery as single part.
Please note: in application with polyamid pipes you have to insert an metal bushing in advance!

max.diameter: 12 mm
wide: 8,5mm
re-usable

1,25 €inclusive VAT, plus shipping costs

Delivery in 1-3 days

Art.No. 6203

Hose clip 7 - 11 / 5 stainless steel

Detail

Hose clips made of stainless steel, for fuel hoses from diameter 7mm up to 11mm.
The wide of the clip is 5mm.

2,85 €inclusive VAT, plus shipping costs

Delivery in 1-3 days

Art.No. 6035

Texture-fuel hose 8mm and clamps

Fuel hose, 8 mm (insde diameter)

Detail

inside diameter: 8 mm
material: petrol resistant rubber with outside texture
made in Germany

priece per Meter: 6,22 Euro

6,22 €inclusive VAT, plus shipping costs

Delivery in 1-3 days

Art.No. 729

Hose clip for fuel hose, 8 mm with texture

Detail

Clamp fpr flexible fuel hose (8mm inside diameter) with outside texture. Best use for the fexible connection between fuel tank an carburettor or between metal / polyamid pipes and components like: tank, carburettor, fuel filter, fuel pump...
Delivery as single part.
Please note: in application with polyamid pipes you have to insert an metal bushing in advance!

max.diameter: 13mm
wide: 9mm
re-usable

1,89 €inclusive VAT, plus shipping costs

Delivery in 1-3 days

Art.No. 8159

Hose clip for fuel hose, 8 mm with texture

Detail

max.diameter: 13 mm
wide: 9,5mm
re-usable

1,35 €inclusive VAT, plus shipping costs

Delivery in 1-3 days

Art.No. 8160

Rubber fuel hose 6mm and clamps

Rubber Fuel hose, 6 mm

Detail

Flexible fuel hose with inside texture and rubber surface.
Best use for the fexible connection between fuel tank an carburettor or between metal / polyamid pipes and components like: tank, carburettor, fuel filter, fuel pump...
Delivery as single part without mounting bits.
The price is for each 1m lenght.
If you order for example 3x 1m so you will get one piece with 3m length and so on.

inside diameter: 5,5 mm
material: petrol resistant rubber with inside texture
made in Germany

priece per meter: 4,93 Euro

4,93 €inclusive VAT, plus shipping costs

Delivery in 1-3 days

Art.No. 7113

Hose clip for fuel hose 6 mm with rubber surface

Detail

Clamp fpr flexible fuel hose (6mm inside diameter) with inside texture. Best use for the fexible connection between fuel tank an carburettor or between metal / polyamid pipes and components like: tank, carburettor, fuel filter, fuel pump...
Delivery as single part.
Please note: in application with polyamid pipes you have to insert an metal bushing in advance!

max.diameter: 12mm
wide: 9mm
re-usable

1,85 €inclusive VAT, plus shipping costs

Delivery in 1-3 days

Art.No. 8162

Hose clip for fuel hose, 6 mm with rubber surface

Detail

Clamp fpr flexible fuel hose (6mm inside diameter).
Best use for the fexible connection between fuel tank an carburettor or between metal / polyamid pipes and components like: tank, carburettor, fuel filter, fuel pump...
Delivery as single part.
Please note: in application with polyamid pipes you have to insert an metal bushing in advance!

max.diameter: 12 mm
wide: 8,5mm
re-usable

1,05 €inclusive VAT, plus shipping costs

Delivery in 1-3 days

Art.No. 8161

Rubber fuel hose 8mm and clamps

Rubber Fuel hose, 7,5 mm

Detail

Flexible fuel hose with inside texture and rubber surface. Inside diameter 7,5mm.
Best use for the fexible connection between fuel tank an carburettor or between metal / polyamid pipes and components like: tank, carburettor, fuel filter, fuel pump...
Delivery as single part without mounting bits.
The price is for each 1m lenght.
If you order for example 3x 1m so you will get one piece with 3m length and so on.

inside diameter: 7,5 mm
material: petrol resistant rubber with inside texture
made in Germany

price per meter: 5,10 Euro

5,10 €inclusive VAT, plus shipping costs

Delivery in 1-3 days

Art.No. 6308

Hose clip for fuel hose 7,5 mm with rubber surface

Detail

Clamp fpr flexible fuel hose (7,5mm inside diameter) with inside texture. Best use for the fexible connection between fuel tank an carburettor or between metal / polyamid pipes and components like: tank, carburettor, fuel filter, fuel pump...
Delivery as single part.
Please note: in application with polyamid pipes you have to insert an metal bushing in advance!

max.diameter: 14mm
wide: 9mm
re-usable

1,85 €inclusive VAT, plus shipping costs

Delivery in 1-3 days

Art.No. 8163

Hose clip for fuel hose, 7,5 mm with rubber surface

Detail

Clamp fpr flexible fuel hose (8mm inside diameter).
Best use for the fexible connection between fuel tank an carburettor or between metal / polyamid pipes and components like: tank, carburettor, fuel filter, fuel pump...
Delivery as single part.
Please note: in application with polyamid pipes you have to insert an metal bushing in advance!

max.diameter: 14 mm
wide: 8,5mm
re-usable

1,05 €inclusive VAT, plus shipping costs

Delivery in 1-3 days

Art.No. 8164

Fuel tank for KA, KB Detail
104,93 €inclusive VAT, plus shipping costs temporary not available Art.No. 4554

Float needle valve W1,3 / T1,1 / B1000-1

Detail

Valve for controlling the petrol level for the carburettor type:

32F 1-1 Trabant 1.1
34 TLA 51/2 Wartburg 1,3
34F 1-3 Barkas 1000-1
original spare part number: 135 29 40 230 078216

19,55 €inclusive VAT, plus shipping costs

Delivery in 1-3 days

Art.No. 82

Set of carburettor membranes W1,3 / T1,1 / B1000-1

Detail

Membranes inserts for the carburettor type:

32F 1-1 Trabant 1.1
34 TLA 51/2 Wartburg 1,3
34F 1-3 Barkas 1000-1

86,90 €inclusive VAT, plus shipping costs

temporary not available

Art.No. 7925

Ring eye D12mm, connection 6mm hose

Detail

Ring terminal ideal for doing byself to fix fuel hoses.
Best use for many old- and Youngtimers to make fuel pessure pipes or normal pertol connection hoses.
Can be used for banjo screws D= 12mm

Eye diameter: 12mm
diameter pipe connection: 6mm

4,85 €inclusive VAT, plus shipping costs

Delivery in 1-3 days

Art.No. 7539

Ring eye D12mm, connection 8mm hose

Detail

Ring terminal ideal for doing byself to fix fuel hoses.
Best use for many old- and Youngtimers to make fuel pessure pipes or normal pertol connection hoses.
Can be used for banjo screws D= 12mm

Eye diameter: 12mm
diameter pipe connection: 8mm

5,95 €inclusive VAT, plus shipping costs

Delivery in 1-3 days

Art.No. 7540

Ring eye D12mm with pipe bend

Detail

Ring terminal ideal for doing byself to fix fuel hoses.
Best use for many old- and Youngtimers to make fuel pessure pipes or normal pertol connection hoses.
Can be used for banjo screws D= 12mm

Eye diameter: 12mm
diameter pipe connection: 8mm
pipe bend: 90 degree
pipe length total: 74mm

15,38 €inclusive VAT, plus shipping costs

Delivery in 1-3 days

Art.No. 7517

Ring eye D10mm with pipe bend

Detail

Ring terminal ideal for doing byself to fix fuel hoses.
Best use for many old- and Youngtimers to make fuel pessure pipes or normal pertol connection hoses.
Can be used for banjo screws D= 10mm

Eye diameter: 10mm
diameter pipe connection: 6mm
pipe bend: 90 degree
pipe length total: 55mm

14,99 €inclusive VAT, plus shipping costs

Delivery in 1-3 days

Art.No. 7516

Ring eye D10mm, connection 6mm hose

Detail

Ring terminal ideal for doing byself to fix fuel hoses.
Best use for many old- and Youngtimers to make fuel pessure pipes or normal pertol connection hoses.
Can be used for banjo screws D= 10mm

Eye diameter: 10mm
diameter pipe connection: 6mm

4,60 €inclusive VAT, plus shipping costs

Delivery in 1-3 days

Art.No. 7537

Ring eye D10mm, connection 8mm hose

Detail

Ring terminal ideal for doing byself to fix fuel hoses.
Best use for many old- and Youngtimers to make fuel pessure pipes or normal pertol connection hoses.
Can be used for banjo screws D= 10mm

Eye diameter: 10mm
diameter pipe connection: 8mm

4,90 €inclusive VAT, plus shipping costs

Delivery in 1-3 days

Art.No. 7538

Carburettor Barkas B1000

Detail

Complete overhauled Carburettor for the three cylinder two stroke Wartburg engine with 1000 ccm
cylinder capacity. delivery without intake pipe.
Carburettor type: 40F 1-12

complete overhauled
high quality from Germany

Please note, we can only repair this spare part if you ship 1x carburettor BVF 40 1- to our company in advance!

Please send in advance one brake cylinder original IFA to our company.

280,00 €inclusive VAT, plus shipping costs

Lieferbar innerhalb von 6-8 Wochen.

Art.No. 7032

fuel stabiliser, 250ml Detail for trouble free over-wintering of engines and fuel tanks. The volume of the boddle protect 50 liter petrol.
priece per Liter: 59,72 Euro	14,93 €inclusive VAT, plus shipping costs Delivery in 1-3 days Art.No. 6671