spareparts for the car electrical system

Category spareparts for the car electrical system has the subcategory

The product category Barkas B 1000 > Spare parts > Electrical system is spread over 8 sites:

Rubber membrane plug for holes with diameter of 20,5mm Detail Membrane plug made of black rubber (Polychloropren) to shut round holes in car bodys (such as service holes) or as variable cable grommet seal for some wires (also with plugs) fit to hole diameter of 20,5 mm inner diameter of membrane (max. usable diameter): 13,5 mm outer diameter (total): 25 mm thickness: 7 mm
1,05 €inclusive VAT, plus shipping costs Delivery in 1-3 days Art.No. 6797

Rubber membrane plug for holes with diameter of 37mm Detail Membrane plug made of black rubber to shut round holes in car bodys (such as service holes) or as variable cable grommet seal for some wires (also with plugs) fit to hole diameter of 37 mm inner diameter of membrane (max. usable diameter): 29 mm outer diameter (total): 44 mm
1,75 €inclusive VAT, plus shipping costs Delivery in 1-3 days Art.No. 6799

Auxiliary diode base plate for Dynamo AC

Detail

Spare base plate pre installed with excitation diodes.
Best use for exchanging the single complete componet.
Delivery without mounting parts.
Fit to dynamo 12V Trabant 601
Trabant 1,1 and Wartburg 1,3 as well Barkas B1000-1

original spare part
one base plate will be needed

original spare part number: 8042.4-412/2

9,77 €inclusive VAT, plus shipping costs

Delivery in 1-3 days

Art.No. 7622

Isolating plate for auxiliary diode base plate

Detail

Spare plasic isolating plate for the base plate (excitation diodes) for Dynamo AC
Delivery without mounting parts.
Fit to dynamo 12V Trabant 601
Trabant 1,1 and Wartburg 1,3 as well Barkas B1000-1

original spare part
one isolating plate will be needed

original spare part number: 8042.4-412/2:2/1

3,51 €inclusive VAT, plus shipping costs

Delivery in 1-3 days

Art.No. 7662

Diode base plate for Dynamo AC

Detail

Spare base plate complete pre installed with excitation diodes and plus diodes.
Best use for exchanging the complete componet.
Delivery without mounting parts.
Fit to dynamo 12V Trabant 601
Trabant 1,1 and Wartburg 1,3 as well Barkas B1000-1

original spare part
one base plate will be needed

original spare part number: 8042.4-410

49,44 €inclusive VAT, plus shipping costs

Delivery in 1-3 days

Art.No. 7601

Brush for starter

Detail

Spare-brushes of the starter engine to solder on at the coil set.
Can be used for all kind of starters 6V and 12V left- and right turning (without Trabant 1.1, Wartburg 1.3 and Baraks B1000-1)
mounting place: brushholder bas plate

size: 16X19x7
delivery as an single part
for each starter two pieces will needed

original spare part number: 8202.11-220:10

8,24 €inclusive VAT, plus shipping costs

Delivery in 1-3 days

Art.No. 785

Bolt for starter

Detail

Bolt of the Bearing case of the starter engine.
Connection bolt will be mounted at the beraing case threadholes and on the other side it will hold the rear case cover.
Delivery as a single part without nuts an washers.
Can be used for all kind of starters 6V and 12V left- and right turning (without Trabant 1.1, Wartburg 1.3 and Barkas B1000-1)

original spare part
surface: galvaniced
total length: 16.5 cm
delivery as an single part
for each starter two pieces will needed

original spare part number: 8202.1-000:4/1

2,93 €inclusive VAT, plus shipping costs

Delivery in 1-3 days

Art.No. 7658

Spring for brush starter

Detail

Pressure spring for the brushes of the starter engine.
This spring will push the brush at the collector ring from the rotor shaft.
Can be used for all kind of starters 6V and 12V left- and right turning (without Trabant 1.1, Wartburg 1.3 and Barkas B1000-1)
mounting place: brushholder bas plate

original spare part
delivery as an single part
for each starter two pieces will needed

original spare part number: 8202.11-220.6

1,55 €inclusive VAT, plus shipping costs

Delivery in 1-3 days

Art.No. 7629

switch unit for ignition look switch Detail Switch insert for ignition look. Electrical part of ignition look switch wich is mounted at the backside. Latest version with six blad terminals. Best quality form the original manufacture made in Germany. Fit to Wartburg 353, 1.3, Barkas B1000 and B1000-1
original spaer part number: 8630.10	19,72 €inclusive VAT, plus shipping costs Delivery in 1-3 days Art.No. 7719

The product category Barkas B 1000 > Spare parts > Electrical system is spread over 8 sites:

1 2 3 4 5 6 7 8
Show all products

* All prices inclusive VAT and plus shipping costs.