This site in german: Wartburg 1.3 > Ersatzteile > Elektrik 
You are here: > Wartburg 1.3> Spare parts> Electrical system

Electrical system

Category Electrical system has the subcategory

The complete offer in Electrical system

cable for positive pole of car battery W1,3

Connection cable between positive pole of car battery and the terminal screw of starter.
Fit to all body types of Wartburg 1.3 like Limousine, Tourist and Trans.
Made of high quality coper wire with additional tin-plated single strands. The double isolation is coated at the outside with an flexible and resistant rubber.
  • length: 710mm
  • pre-finished
  • one cable tail with battery pole terminal
  • one cable tail with 8mm cable shoe for terminal screw of solenoid switch (mounted on starter)
  • thick and robust isolation (outer diameter: 13,3mm)
  • new made in Germany
  • copper cable
50,81 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 7966

Ground cable for car battery W1,3

Connection cable between negative pole of car battery and the mounting screw of gearbox and engine (earth-connection, ground).
Fit to all body types of Wartburg 1.3 like Limousine, Tourist and Trans.
Made of high quality coper wire with additional tin-plated single strands. The double isolation is coated at the outside with an flexible and resistant rubber.
  • length: 1030mm
  • pre-finished
  • one cable tail with battery pole terminal
  • one cable tail with 8mm cable shoe
  • thick and robust isolation (outer diameter: 13,3mm
  • new made in Germany
  • copper cable
41,95 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 7965

interval relais for windsreen wiper

interval relais for windsreen wiper
for yellow connector (6 pin)

original-IFA-spare part
36,14 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 6422

Interior lamp Wartburg

Lamp for the passenger compartments Wartburg 353 and Wartburg 1,3.
Can be used for 6V and 12V tubular lams 5W.
  • Original spare part
  • delivery without bulbs
  • delivery inclusive two mounting screws
original spare part number: 8838.174
28,11 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 7756

Mounting screw for interior lamp Wartburg

Truss-head screw made of stainless stell for mounting the lamp for the passenger compartments Wartburg 353 and Wartburg 1,3.
  • Original type of screw
  • material: stainless steel
  • delivery as an single part
  • two pieces will be needed
0,15 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 7757

Fuse 8A

white fuse for current up to 8A

fit to all vehicles with this type of fuse
0,25 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 1220

Key switch

One grade switch made of Duro-plastic
Can be used for 6,12 (120W) and 24V (150W) electrical systems.
Best use for additional electrical units at Old- and Youngtimers.
original spare part number: 8600.21/1
1,95 €inclusive VAT, plus shipping costs
0temporary not available
temporary not available

Art.No. 7590

Fuse set

Torpedo-fuse kit ideal for traveles or for the daily use.
Delivery with resealable blister box.
Scope of delivery:
  • 4x 8A (withe)
  • 4x 16A (red)
  • 2x 25A (blue)
2,50 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 6437

Rocker switch rear window defroster

Angular single step switch with function light for mounting at the dashboards of the Wartburg 1,3.
Colour of the switch: black
symbol: window defroster
colour of the functions light: orange
original spare part
Delivery without bulbs, it will be for example glas base bulb 12V 1,2W one needed.
original spare part number: 8620.19/252
9,88 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 7732

Single grade pull switch

Small pull switch for mounting for example at the dashboards.
Can be used for 6,12 and 24V electrical systems.
Space saving frame size, best use for additional electrical units at Old- and Youngtimers.
original spare part number: 8600.23
4,76 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 7589

Rocker switch rear wiper Tourist

Angular single step switch with pushbutton for the screen washing.
Mounting at the dashboards of the Wartburg 1,3 station wagons.
Colour of the switch: black
symbol: wiper
original spare part.
original spare part number: 8620.19/203
11,25 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 7733

Fuse 16A

red fuse for current up to 16A

fit to all vehicles with this type of fuse
0,25 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 1221
2+1
1+1

Dynamo AC 12V, four stroke

Rotary current generator (14V, 57A) complete in germany overhauled spare part.
Fit to Trabant 1,1 and Wartburg 1,3 and Barkas B1000-1 with four stroke engine.
Scope of delivery inclusive voltage regulator.
Overhaul part, please send the starter motor in advance to our company
Delivery only in exchange! Please send in advance one brake cylinder original IFA to our company.
289,17 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 762

V-belt AVX 10 x 700

Alternator belt fit to Wartburg 1,3, Trabant 1,1 and Barkas B1000-1.
  • dimensions: 10mm wide, 700mm long
  • made in England
7,61 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 1106

Electrical mixture preheater

electrical mixture preheater for Trabant 1.1 and Wartburg 1.3
96,10 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 801

Paper sealing for electrical mixture preheater

Upper paper seal for the electrical mixture preheater.
Fit to Trabant 1.1 and Wartburg 1.3
  • material: sealing paper
  • high quality reproduction
3,94 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 7971

Sealing ring for electrical mixture preheater

Special sealing ring for the electrical mixture preheater.
Fit to Trabant 1.1 and Wartburg 1.3
  • material: sealing rubber
  • high quality reproduction
9,36 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 7976

Starter 12V *reclaimed* (T1.1/W1.3/B1000-1)

Complete overhauled starter for Trabant 1,1 Wartburg 1,3 and Barkas B1000-1
with 4-cylinder 4-stroke engine.
Delivery inclusive solenoid switch.
Please send your Trabant starter 12V in advance to our company for reparing.
  • delivery inclusive starter magnet
  • for 12V system
  • overhauled in Germany
Overhaul part, please send the starter motor in advance to our company
235,45 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 6417
1+1

Regulator and cutout relay for AC 12V Dynamo

The voltage regulator is direct mounted at the dynamo. Fit to many IFA dynamos with rotary current. for example:

  • original spare part
  • one piece will be needed
DLR TGL33604
47,93 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 775

Solenoid switch for starter

Fit to Starter 12V T 1.1 and W1.3 and Starter 12V remanufactuered Trabant 1.1 and Wartburg 1.3
  • remanufactrued EU
  • one piece will be needed
61,88 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 6651

Brush for Dynamo AC

Spare brush fit to AC Dynamo 12V Trabant 1.1, Wartburg 1.3 and Barkas B1000-1
  • original spare part (NOS)
  • price for each one
  • two pieces will be needed

size:15,5mm x 10mm x 5mm
wire: 40mm
flat plug 6,3mm
original spare part number: 8042.1-041
5,51 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 7598

Signal horn 6V

Universal signal horn for the supply voltage 6V.
Also for any type of vehicle with voltage of 6V.
Best use for Old-and Youngtimers.
  • metal-body, galvaniced / chrome
  • outside diameter: 98mm
  • inclusive grounding clip
  • one piece will be needed
19,81 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 7618

Signal horn, 12V

universal signal horn for the supply voltage 12V.
Also for any type of vehicle with voltage of 12V (like Audi, VW, Opel, Ford and more).
  • galvaniced metal-body
  • inclusive grounding clip
  • made in Germany
  • one piece will be needed
17,46 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 1205

Oel pressure switch, colour brown

Oel pressure switch
it opens if oil pressure is more than 30 kPa (+/-15 kPa)
colour of plastic: brown

original name of the part:
DTR 8640.9/2.1.1
14,88 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 841

Oel pressure switch, black

oel pressure switch
it closes if oil pressure is more than 140 kPa (+/-20 kPa)
colour of plastic: black

original name of the part:
DTR 8640.10/17.1.1
14,88 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 840

Transmitter for temperature indication

transmitter for temperature indication is screwed into thermostat housing
14,04 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 851

Thermo switch

Thermostat is mounted in thermotat housing
The thermo switch is a earthless closed-circuit current switch for warm running automatic.
It open if cooling water temperature is about 60°C.
27,13 €inclusive VAT, plus shipping costs
0temporary not available
temporary not available

Art.No. 850

electrical pump for windscreen washer

electrical pump to put into the water bottle of windscreen washer
voltage: 12V

fit to follow washer systems:
windscreen Trabant 601
rear window Wartburg 353 and 1.3 TOURIST (only for estate wagon)
42,46 €inclusive VAT, plus shipping costs
0temporary not available
temporary not available

Art.No. 1125

controller-unit for overrun cut-off (T1.1/W1.3)

Electronical control unit for overrun cut-off of 4-stroke engines of Trabant or Wartburg.
Discontinues the fuel supply during overrun. Works in tandem with Switch for throttle valve und tick-over valve
81,29 €inclusive VAT, plus shipping costs
0temporary not available
temporary not available

Art.No. 6489

Relais 12V 50A (changeover contact)

Additional relais for operating supply 12V DC with changeover contact. The maximum current 30 ampere.
  • 5 x blade terminal connection pins (6 x 0,8mm
  • 1x changeover contact (can be used as changeover-, make- or break contact
  • Max. continuous current with 12V DC: 40A (make contact no.87)/ 30A (break contact no.87a)
  • plastic case
  • dimensions: 28 x 28 x 25 mm (without mounting lug)
8,92 €inclusive VAT, plus shipping costs
Lieferbar innerhalb von 6-8 Wochen.

Art.No. 6890

Lamp spare kit H4 / 12V

Spare kit with different bulbs fit to voltage of 12V
content:
  • 1x H4-lamp 60/55W with base P43t
  • 2x spherical lamps 21W white with base Ba15s
  • 1x tubular lamp 21W (C21W) with base SV 8,5
  • 1x tubular lamp 5W (C5W) with base SV 8,5
  • 1x bulb 4W (T4W) with base BA 9s
  • 1x bulb for speedometer 2W with base BA 7s
  • 1x Torpedo-fuse 8A
  • 1x Torpedo-fuse 16A
12,57 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 7057

Lamp spare kit R2 / 12V

Spare kit with different bulbs fit to voltage of 12V
content:
  • 1x R2-lamp 45/40W with base P45t
  • 2x spherical lamps 21W white with base Ba15s
  • 1x tubular lamp 21W (C21W) with base SV 8,5
  • 1x tubular lamp 5W (C5W) with base SV 8,5
  • 1x bulb 4W (T4W) with base BA 9s
  • 1x bulb for speedometer 2W with base BA 7s
  • 1x Torpedo-fuse 8A
  • 1x Torpedo-fuse 16A
14,68 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 6623

Bulbs spare kit R2 / 6V

Spare kit with different bulbs fit to voltage of 12V
content:
  • 1x R2-lamp 45/40W with base P45t
  • 1x spherical lamps 18W white with base Ba15s
  • 1x tubular lamp 18W (C21W) with base SV 8,5
  • 1x tubular lamp 5W (C5W) with base SV 8,5
  • 1x bulb 4W (T4W) with base BA 9s
  • 1x bulb for speedometer 0,6W with base BA 7s
  • 1x spherical lamps 21W white with base Ba15s
  • 1x spherical lamps 5W white with base Ba15s
  • 1x Torpedo-fuse 8A
  • 1x Torpedo-fuse 16A
25,77 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 7145

Speedometer with trip meter

Round speedometer for the cars Wartburg 1.3, Wartburg 353, Trabant 1.1, Barkas B1000 and B100-1.
type:
  • Speedscale up to 150km/h
  • inclusive trip meter
  • power 12V
  • delivery without bulbs and without bulb retainer
  • front rim : black
  • mounting diameter: 100mm
  • genuine spare part
  • Zak No: 3.0230/47
81,64 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 7092

Thermo switch for radiator fan

The thermo switch for radiator fan is a make contact, which is screwed directly into the radiator.
  • It closes contact if temperature of coolant is about 95°C +/- 3K and it closes if temperature is about 89°C +/- 3K.
  • fit for Trabant 1,1 and Wartburg 1,3
  • one piece will be needed
20,28 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 723

Combi-instrument

Round instrument for the cars Wartburg 1,3 and B1000-1.
Original spare part for display the engine temperature and the fuel gauge.
type:
  • late type with LED
  • inclusive connection plug
  • power 12V
  • scope of delivery inclusive without bulbs
  • front rim : black
  • mounting diameter: 100mm
  • genuine spare part
  • Zak No: 3.085101/47
35,90 €inclusive VAT, plus shipping costs
0temporary not available
temporary not available

Art.No. 7354

Rear fog lamp for rear bumper

Rear fog light for the mounting on top of the bumber.
  • colour: black casing, glass red
  • size: 14 x 7,5 cm
  • delivery without bulb
  • original spare part
9,95 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 7413

Fan for radiator

electrical fan for radiator Trabant 1,1. complete with installing frame for radiator.
curency: 12V
  • made in Germany
  • one piece will be needed
77,77 €inclusive VAT, plus shipping costs
0temporary not available
temporary not available

Art.No. 6483

Protection cap for starter lite ( plastic )

Sealing cap to protect the starter wire (plus) against dust and moisture.
Fit to the vehicles: P70, Trabant, Wartburg, Multicar, Framo and Barkas.
  • made in Germany
  • one piece will be needed
6,85 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 786

Roller bearing 6303 ZZ

Single row roller bearing 6303, ZZ, 17x47x14.
High Qualit made by FAG.
Fit to AC generator 12V Trabant, LDM-part-no.: 760 and AC generator 12V Trabant 1.1, Wartburg 1,3 and Barkas B1000-1 LDM-part-no.: 762 rotor shaft front side (end shild)
  • ZZ- synonym for bearing cover, both side
  • dimensions: d=17mm, D=47mm, widness=14mm
  • bearing play CN(CO)-normale bearing play
  • one piece will be needed
  • made by FAG
9,79 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 6333

Roller bearing 6003 ZZ

Single row roller bearing 6003, ZZ, 17x35x10.
Made by FAG.
Fit to AC generator 12V Trabant, Wartburg und Barkasrotor shaft front side
  • ZZ- synonym for bearing cover, both side
  • bearing play CN(CO)-normale bearing play
  • one piece will be needed
  • made by FAG
8,57 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 6330

windscreen washer kit

Complete kit for windscreen washer system with electrical pump and water bottle
voltage: 12V
Scope of delivery:
  • bottle 1,5 liter
  • cap
  • metal holder
  • wash pump 12V
  • 1m plastic hose (connection pump-spray jet
  • 1 piece of two double jet washer inclusive retainer spring

fit to follow washer systems:
windscreen Trabant 601
Wartburg 353 and 1.3 Tourist rear window
56,53 €inclusive VAT, plus shipping costs
0temporary not available
temporary not available

Art.No. 6907

Water vessel for windscreen washer system, singel part

Water bottle for windscreen washer system, to use in tandem with electrical pump bottle
Volume: 1,5 liter
original spare part
fit to follow washer systems:
windscreen Trabant 601
Wartburg 353 and 1.3 TOURIST rear window
single part without pump, cap and metal holder
parts-no. 136 65 730
33,80 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 6908

Pessure spring carbon brush

Coil spring for the carbon brushes at the rotary current generator.
Original spare part (NOS)
For each generator two pieces will be needed.
Fit to all generators 12V Trabant 601, Trabant1.1, Wartburg 353, Wartburg 1.3, Barkas B1000 und B1000-1
Original spare part number: 8042.1-040
1,55 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 760

Graphite collector ring rotary current generator

Collector ring for the generator rotor.
Inclusive metal plates for mounting the rotor windings
Original spare part (NOS)
  • For each generator one piece will be needed
  • Fit to all generators 12V Trabant 601, Trabant1.1, Wartburg 353, Wartburg 1.3, Barkas B1000 und B1000-1
Original spare part number: 8042.1-032/1
96,18 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 7599

Bearing cover rotary current generator

Metal cover for the rear ball bearing (rotor shaft rear 6303ZZ) of the rotary current generator to the collector ring.
Original spare part (NOS)
  • metal, galvaniced
  • For each generator one piece will be needed
  • Fit to all generators 12V Trabant 601, Trabant1.1, Wartburg 353, Wartburg 1.3, Barkas B1000 und B1000-1
Original spare part number: 8042.1-030
3,90 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 772

Bolt for regulator

Mounting bolt for regulator and cutout relay.
Original spare part (NOS)
  • threed: M5
  • length: 49mm
  • delivery inclusive nut SW8
  • For each generator tow pieces will be needed
  • Fit to all generators 12V Trabant 601, Trabant1.1, Wartburg 353, Wartburg 1.3, Barkas B1000 und B1000-1
Original spare part number: 8042.401-000
2,45 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 7600

Rubber membrane plug for holes with diameter of 15mm

Membrane plug made of black rubber to shut round holes in car bodys (such as service holes) or as variable cable grommet seal for some wires (also with plugs)

fit to hole diameter of 15 mm
inner diameter of membrane (max. usable diameter): 9 mm
outer diameter (total): 20 mm
0,90 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 6796

Rubber membrane plug for holes with diameter of 18,5mm

Membrane plug made of black rubber to shut round holes in car bodys (such as service holes) or as variable cable grommet seal for some wires (also with plugs)

fit to hole diameter of 18,5 mm (0,728")
inner diameter of membrane (max. usable diameter): 11 mm (0,433")
outer diameter (total): 23 mm (0,906")
0,97 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 6895

Rubber membrane plug for holes with diameter of 28mm

Membrane plug made of black rubber to shut round holes in car bodys (such as service holes) or as variable cable grommet seal for some wires (also with plugs)

fit to hole diameter of 28 mm
inner diameter of membrane (max. usable diameter): 21 mm
outer diameter (total): 35 mm
1,57 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 6798

Rubber membrane plug for holes with diameter of 32mm

Membrane plug made of black rubber to shut round holes in car bodys (such as service holes) or as variable cable grommet seal for some wires (also with plugs)
  • fit to hole diameter of 32 mm
  • inner diameter of membrane (max. usable diameter): 25 mm
  • outer diameter (total): 39 mm
  • thicknes of the menbrane: 1mm
  • total thickness: 9mm
2,23 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 7613

Rubber membrane plug for holes with diameter of 47mm

Membrane plug made of black rubber to shut round holes in car bodys (such as service holes) or as variable cable grommet seal for some wires (also with plugs)
  • fit to hole diameter of 47 mm
  • inner diameter of membrane (max. usable diameter): 36 mm
  • outer diameter (total): 54 mm
  • thicknes of the menbrane: 1mm
  • total thickness: 10mm
2,98 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 6800
1+1

Rubber membrane plug for holes with diameter of 20,5mm

Membrane plug made of black rubber (Polychloropren) to shut round holes in car bodys (such as service holes) or as variable cable grommet seal for some wires (also with plugs)

fit to hole diameter of 20,5 mm
inner diameter of membrane (max. usable diameter): 13,5 mm
outer diameter (total): 25 mm
thickness: 7 mm
1,05 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 6797

Rubber membrane plug for holes with diameter of 25mm

Membrane plug made of black rubber (Polychloropren) to shut round holes in car bodys (such as service holes) or as variable cable grommet seal for some wires (also with plugs)

fit to hole diameter of 25 mm
inner diameter of membrane (max. usable diameter): 18,5 mm
outer diameter (total): 30,5 mm
thickness: 7 mm
1,27 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 7625

Rubber membrane plug for holes with diameter of 37mm

Membrane plug made of black rubber to shut round holes in car bodys (such as service holes) or as variable cable grommet seal for some wires (also with plugs)

fit to hole diameter of 37 mm
inner diameter of membrane (max. usable diameter): 29 mm
outer diameter (total): 44 mm
1,75 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 6799

Auxiliary diode base plate for Dynamo AC

Spare base plate pre installed with excitation diodes.
Best use for exchanging the single complete componet.
Delivery without mounting parts.
Fit to dynamo 12V Trabant 601
Trabant 1,1 and Wartburg 1,3 as well Barkas B1000-1
  • original spare part
  • one base plate will be needed
original spare part number: 8042.4-412/2
9,77 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 7622

Diode base plate for Dynamo AC

Spare base plate complete pre installed with excitation diodes and plus diodes.
Best use for exchanging the complete componet.
Delivery without mounting parts.
Fit to dynamo 12V Trabant 601
Trabant 1,1 and Wartburg 1,3 as well Barkas B1000-1
  • original spare part
  • one base plate will be needed
original spare part number: 8042.4-410
49,44 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 7601

Isolating plate for auxiliary diode base plate

Spare plasic isolating plate for the base plate (excitation diodes) for Dynamo AC
Delivery without mounting parts.
Fit to dynamo 12V Trabant 601
Trabant 1,1 and Wartburg 1,3 as well Barkas B1000-1
  • original spare part
  • one isolating plate will be needed
original spare part number: 8042.4-412/2:2/1
3,51 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 7662

switch unit for ignition look switch

Switch insert for ignition look.
Electrical part of ignition look switch wich is mounted at the backside.
Latest version with six blad terminals.
Best quality form the original manufacture made in Germany.
Fit to Wartburg 353, 1.3, Barkas B1000 and B1000-1
original spaer part number: 8630.10
19,72 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 7719

Fuse box eigth fold

Fuse box inclusive 8 fuses. Wire connection with mounting screws.
Type with 8 single places for fuses.
Cover mede of clear glass plastic.
Useable for Ifa cars and many Old- and Youngtimers.
18,24 €inclusive VAT, plus shipping costs
0temporary not available
temporary not available

Art.No. 8036

Fuse box sixfold

Fuse box inclusive 6 fuses. Wire connection with mounting screws.
Type with 6 single places for fuses.
Cover mede of clear glass plastic.
Useable for Ifa cars and many Old- and Youngtimers.
19,54 €inclusive VAT, plus shipping costs
0temporary not available
temporary not available

Art.No. 8035

Fuse box SDB/8

Retainer for the fuses (8 pieces) as terminal block with clamp connection for the wires.
Fit to Trabant 601 Limousine, Universal and Kuebel.
  • original spare part
  • delivery complete cover
  • delivery without fuses
origial spare part no: 8811.11
36,44 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 7475

Wiper motor 12V

Wiper motor as universal unit with 12V sytem. This Repro part can be used for the car types: Multicar M22, M24, M25, Wartburg 353 and 1,3, Baraks B1000 and B1000-1, Trabant 601 (from vintage 88) and Trabant 1,1.
Inexpensive option to the original spare part.
The base plate can be turend to modificate the wiper motor for your car type.
The wire connection have to be done byself.
  • delivery as an single part
  • without wires or wire plugs
  • one piece will be needed
  • 12V system
89,73 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 8357

Carrier for carbon brush

Retainer for the carbon brushes at the rotary current generator.
New produced spare part.
For each generator one piece will be needed.
Fit to all generators 12V Trabant 601, Trabant1.1, Wartburg 353, Wartburg 1.3, Barkas B1000 und B1000-1, Multicar M25
17,85 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 8495

Switch and timing switch for wiper motor

Combination switch with 2 level timing,2 level of wiper speeds and button for screen water.
Switch for wiper motor 12V.
Delivery inklusive knob for Trabant-Types. The switch can be modificatet with the knob for Wartburg, Barkas, Multicar ec.
  • New produced spare part
  • one piece will be needed
53,63 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 1117

Set of cable grommet seal

One set of cable grommet seals with different sizes.
Contens:
  • 40 pieces body hole: 6mm / wire bore: 2mm
  • 40 pieces body hole: 7,5mm / wire bore: 5mm
  • 40 pieces body hole: 9mm / wire bore: 6mm
  • 25 pieces body hole: 11mm / wire bore: 8,5mm
  • 20 pieces body hole: 12mm / wire bore: 10mm
  • 5 pieces body hole: 15mm / wire bore: 12mm
  • 5 pieces body hole : 20,5mm / wire bore: 14,5mm
  • 5 pieces body hole: 23,5mm / wire bore: 17,5mm
15,86 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 8608
The complete offer in Electrical system

* All prices inclusive VAT and plus shipping costs.
© 2003 - 2023 LDM-tuning.de
Ersatzteile für Trabant, Wartburg und Barkas