spare parts for cluch Barkas B1000 and B1000-1

Complete clutch set with diameter of clutch and clutch disc of 200 mm.
It fit to Barkas B1000 2-stroke engine (vintage of vehicle: from 03/1985 onwards).
contens:

• clutch (Art.No.: 4431)
• clutch disc (Art.No.: 4433)
• release bearing Art.No.: 680

Please note:

These are remanufactured parts, components, or assemblies! Due to resource constraints, this item is only available as an immediate repair part. The price displayed applies exclusively to the standard labor of remanufacturing (repair) of the submitted component. The price does not constitute a right to purchase the actual component! Please send us remanufacturable components (German IFA production) for repair in advance.

Clutch for Barkas B1000 two stroke engine from year 3/1985,

• fit to clutch disk D= 200 mm
  
• one piece will be needed
• Made in Germany

Please note:

These are remanufactured parts, components, or assemblies! Due to resource constraints, this item is only available as an immediate repair part. The price displayed applies exclusively to the standard labor of remanufacturing (repair) of the submitted component. The price does not constitute a right to purchase the actual component! Please send us remanufacturable components (German IFA production) for repair in advance.

clutch disk for Barkas B1000 2-stroke engine

• diameter 200 mmm
• for vehicles with vintage from 03/1985 onwards
• one piece will be needed
• Made in Germany

fit to Slip ring disengager, Cluch

Please note:

Note: These are remanufactured parts, components, or assemblies! Due to resource constraints, this item is only available as an immediate repair part. The price displayed applies exclusively to the standard labor of remanufacturing (repair) of the submitted component. The price does not constitute a right to purchase the actual component! Please send us remanufacturable components (German IFA production) for repair in advance.

Set of two pieces friction surfaces for clutches 200mm diameter.
Best for self made at the worn out clutch disc.
Fit for for Barkas B1000 two stroke(vintage up to 02/1985) and Barkas B1000-1 four stroke.

• size: 200x135x3,5mm
• not pree drilled
• made in germany

Set of two pieces friction surfaces for clutches 200mm diameter.
Spare part for the clutch disc made by Valeo.
Best for self made at the worn out clutch disc.
Fit for for Barkas B1000 two stroke(vintage up to 02/1985) and Barkas B1000-1 four stroke.

• size: 200x137x3,2mm
• complete pree drilled
• made in germany

clutch disk for Barkas B1000 2-stroke engine

• diameter 200 mmm
• for vehicles with vintage from 03/1985 onwards
• one piece will be needed

fit to Slip ring disengager, Cluch

Complete clutch set with diameter of clutch disc of 200 mm.
It fit to Barkas B1000 2-stroke engine (vintage of vehicle: from 03/1985 onwards).
contens:

• clutch (Art.No.: 6594)
• clutch disc (Art.No.: 4433)
• release bearing Art.No.: 3104

Note: These are remanufactured parts, components, or assemblies! Due to resource constraints, this item is only available as an immediate repair part. The price displayed applies exclusively to the standard labor of remanufacturing (repair) of the submitted component. The price does not constitute a right to purchase the actual component! Please send us remanufacturable components (German IFA production) for repair in advance.

Clutch for Barkas B1000 models up to year February 1985.

• fit to clutch disc diameter 180mm, our order no. 3100)
• with additional thrust bearing for old version of release bearing
• one piece will be needed

clutch disc with springs

fit for all variants of Wartburg 353, for Barkas B1000 (vintage up to 02/1985) and also for Multicar M24
diameter: 180 mm
Please note:

Exchange part

Delivery only in exchange, you have to ship one overhaulable clutch disk in advance !

Set of two pieces friction surfaces for clutches 180mm diameter.
Best for self made at the worn out clutch disc.
Fit for all variants of Wartburg 353 (without vintage limit), for Barkas B1000 (vintage up to 02/1985) and also for Multicar M24

• size: 180x124x3,5mm
• complete pree drilled
• made in germany

Complete clutch set
Clutch set fit to Barkas B1000-1 with 4-stroke engine.
Diameter of this clutch is also 200mm, but it is NOT the same like the 2-stroke type.
contens:

• clutch (Art.No.: 4430)
• clutch disc (Art.No.: 4432
• release bearing (Art.No.: 680)

Please note: you have to send one clutch disc Barkas B1000-1 in advance to our comapny !

This needle bearing for the clutch shaft is mounted inside of the Brakas B1000-1 crank shaft.

• delivery as single part
• one piece will be needed

Exchange spare part cluch for Barkas B1000 4-stroke engine
fit to cluch disk 4-stroke engine
{[Fit to clutch disc (four stroke)][one piece will be needed]}
For more informations to this exchange part please use the Detail button.

cluch disk for Barkas B1000-1 with 4-stroke engine

• fit to Slip ring disengager, Cluch
• one piece will be needed

For more informations to this exchange part please use the Detail button.

Retainer wire to fic the clutch cable at the vehicle frame or holder.
Can be used for Fahrzeuge: Wartburg 311,312, 313, Wartburg 353 and 1.3 and Barkas B1000 und B1000-1.
High quality reproduction.

• material: spring steel
• one piece will be needed

Clutch cable for the Barkas B1000. Fit to all two stroke models with mechanical cable clutch system.

• total length 930 mm
• one piece will be needed
• original spare part

Clutch cable for the Barkas B1000. Fit to all two stroke models with mechanical cable clutch system.

• total length 930 mm
• one piece will be needed

Clutch cable for the Barkas B1000-1 wit four stroke engine. Fit to all models with, mechanical cable clutch system.
Good quality reproduction

• total length 980 mm
• one piece will be needed

Reproducted clutch cylinder for the Barkas B1000. Fit to all two stroke models with hydraulic clutch system.
The cluch master cylinder has an bore of 19mm

• new production
• Made in EU
• one piece will be needed

Scope of delivery:
1x dust cap for clutch master cylinder (B1000, 2-takt/M22) (LDM-part.no.:8253)

Complete in Germany overhauled clutch cylinder for the Barkas B1000. Fit to all two stroke models with hydraulic clutch system.
The cluch master cylinder fit also to Multicar M22.
Case type: Renak BH7

• refreshed in Germany
• original spare part
• we use only high quality sealing rings (LDM-Art.Nr.: 7169) for overhauling
• one piece will be needed

additional needed parts (not scope of delivery)
1x dust cap for clutch master cylinder (B1000, 2-takt/M22) (LDM-part.no.:8253)
For more informations to this exchange part please use the Detail button.

Sleeves for the clutch cylinder of the Barkas B1000 and Multicar M22. Fit to all two stroke models of Barkas with hydraulic clutch system.
Set consist of 1x ring sleeve and 1x cap sleeve.

• made in Germany
• genuine spare part
• one set will be needed

Sealing cap for the hydraulic clutch master cylinder of the Barkas B1000. Fit to all two stroke models with hydraulic clutch system. Also fit to Multicar M22.
Best protection against dust, dirt and moisture.

• Reproduction by the original manufacture
• made in Germany
• material: rubber, clour black
• one piece will be needed

Overhauled clutch cylinder for the Barkas B1000. Fit to all two stroke models with hydraulic clutch system.
Type: KZ25

• overhauled in Germany
• genuine spare part
• one piece will be needed

For more informations to this exchange part please use the Detail button.

New producted clutch cylinder, gearbox side for the Barkas B1000. Fit to all two stroke models with hydraulic clutch system.
Type: KZ25

• Repoduction made in EU
• one piece will be needed

Ring sleeve for the clutch cylinder release fork of the Barkas B1000. Fit to all two stroke models with hydraulic clutch system.

• made in Germany
• genuine spare part
• one set will be needed

Felxible connection hose inclusive mounted srews. This hose will connect the clutch master cylinder (frame) and the clutch cylinder (gearbox side) at the Barkas B1000. Fit to all two stroke models with hydraulic clutch system.

• made in EU
• one piece will be needed

Connection pipe inclusive mounted srews. This tube will connect the clutch master cylinder (frame) and the clutch cylinder (gearbox side) at the Barkas B1000. Fit to all two stroke models with hydraulic clutch system.

• made in Germany
• one piece will be needed

Ring terminal, mounting one hand with banjo screw M12 and on the other end by brake pipe or brake hose (M12x1)

technical specifications:

• material: Aluminium
• bore size for banjo screw: 12,1mm, thickness: 11,2mm
• thread: M12x1 Type E
• delivery without mounting bits

banjo screw for mounting the aluminium terminal at the tandem brake master cylinder, clutch master cylinder or cluch slave cylinder Barkas B1000.

technical specifications:

• thread: M12x1
• spanner gap: SW17
• total length: 24 mm
• thread length: 11,5 mm
• inner diameter: 3,5 mm