This site in german: Wartburg 353 > Ersatzteile > Vorderachse 
You are here: > Wartburg 353> Spare parts> Front axle
Navigation

Front axle

Category Front axle has the subcategory

The complete offer in Front axle

Steering wheel Wartburg

Steering wheel for Wartburg, made in Europe.
  • fit to Wartburg 312, 353 and 1.3 modells like Limousine, Tourist, Camping and Trans
  • delivery as an single part
  • one pieces will be needed
123,76 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 8268

Gas pressure telescopic shock absorber, W353, front axle

Two pipe gaspressure buffer for the Wartburg 353 front axle with coil spring. Fit to both typs: Limousine and Tourist from vintage: 1965 up to 1988.
  • scope of delivery inclusive bushing
  • mounting eye on both ends
  • lenght total: 44cm (eye-eye)
  • length pressed: 28cm (Auge-Auge)
  • made in Japan
  • 2 pieces will be needed
68,00 €inclusive VAT, plus shipping costs
0temporary not available
temporary not available

Art.No. 7238

Telescopic shock absorber, W353, front axle

Buffer for the Wartburg 353 front axle with coil spring. Fit to both typs: Limousine and Tourist from vintage: 1965 up to 1988.
  • scope of delivery inclusive bushing
  • mounting eye on both ends
  • made in Germany
  • 2 pieces will be needed
97,63 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 6062

Telescopic shock absorber Sachs for W353, front and rear axle

Buffer made by Sachs for the Wartburg 353 front and rear axle with coil spring. Fit to both typs: Limousine and Tourist from vintage: 1965 up to 1988.
  • scope of delivery inclusive bushing
  • mounting eye on both ends
  • made in Germany
  • two or four pieces will be needed
87,44 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 7887

Rubber sleeve cushion for shock absorber 30mm

The bushing is pressed in to the eye of the shock absorber diameter size 30mm.
Fit to Trabant 500,600,601 leaf spring shocks or Wartburg 311/312/353, DDR trailers shocks and so on...
  • 1x length inner sleeve: 32 mm
  • 1x rubber
  • made in Germany
  • 2 or 4 pieces will be needed
12,90 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 8028

Spring W353, front axle

Coil spring for the Wartburg 353 front axle. Fit to both typs: Limousine and Tourist from vintage: 1965 up to 1988.
  • length of the spring: original (lo=418mm)
  • made in Germany
  • 2 pieces will be needed
78,80 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 7323

Form ring 20mm for Spring, front axle

Rubber form ringfor the coil spring for the Wartburg 353 and 1,3 front axle (Wartburg 312).
This form ring is about 19-20mm thickness.
Plaese check at your Wartburg before, which ring is mounted!
Fit to both typs: Limousine, Tourist and Trans.
  • material: rubber
  • Form ring total thickness: 19-20mm
  • made in Germany
  • 2 pieces will be needed
23,90 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 8645

Form ring 10mm for grinded Spring, front axle

Rubber form ringfor the grinded coil spring for the Wartburg 353 and 312.
This form ring is about 10mm thickness.
Plaese check at your Wartburg before, which ring / Spring type is mounted!
Fit to typs: Limousine, Tourist and Trans.
  • material: rubber
  • Form ring total thickness: 10mm
  • made in Germany
  • 2 pieces will be needed
23,90 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 8652

Form ring 25mm for Spring, front axle

Rubber form ringfor the coil spring for the Wartburg 353 and 1,3 front axle (Wartburg 312).
This form ring is about 25mm thickness.
Plaese check at your Wartburg before, which ring is mounted!
Fit to both typs: Limousine, Tourist and Trans.
  • material: rubber
  • Form ring total thickness: 25mm
  • made in Germany
  • 2 pieces will be needed
23,90 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 8647

Form ring 17mm for grinded Spring, front axle

Rubber form ringfor the grinded coil spring for the Wartburg 353 and 312.
This form ring is about 17mm thickness.
Plaese check at your Wartburg before, which ring / Spring type is mounted!
Fit to typs: Limousine, Tourist and Trans.
  • material: rubber
  • Form ring total thickness: 170mm
  • made in Germany
  • 2 pieces will be needed
23,90 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 8653
Ball joint track rod

Ball joint for trak rod, complete

The ball joint fit to Wartburg 353 and 1,3
Reproduction, made in EU.
  • two pieces will be needed
  • made in Europe

Please use the button detais for the exploded view and find the right spare part.
17,85 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 3300

Look plate ball joint for trak rod

Look plate to secure the mounting connetion between ball joint and track rod.
Fit to Wartburg 353 and 1,3
  • total two pieces will be needed
  • made in Germany

Please use the button detais for the exploded view and find the right spare part.
2,95 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 7240

Sleeve for ball joint

replacement sleeve for ball joint. Fit to Trabant601, Trabant 1,1 and Wartburg 353 and 1,3.
  • It is only recommendable if ball joint is without any slackness
2,60 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 938

Nut for track rod M12, right tap

Trak rod nut for mounting at the connection between clamping nut - ball joint.
Fit to all Wartburg 353 and 1.3
  • strength class: 10.9
  • surface: galvanized
  • thread M14x1,5 right
  • spanner gap SW19
  • for each car two pieces will be needed
  • made in Germany

Please use the button detais for the exploded view and find the right spare part.
1,25 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 7241

Steering rack gaiter (W312/W353 up to Dec.86)

This gaiter for steering fits to Wartburg models 312 and 353 up to December 1986.
  • delivery without mounting parts
  • two pieces will be needed

Please use the button detais for the exploded view and find the right spare part.
17,50 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 3315

Steering rack gaiter (W353 from Jan.87 / W1.3)

This gaiter for steering fits to Wartburg 353 (from January 1987 onwards) and all kind of Wartburg 1,3.
  • delivery without mounting parts
  • two pieces will be needed
14,22 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 7023

Protaction cap for Steering rack (W353 / W1.3)

Dust sealing for the gear rack at the Wartburg steering case.
  • material: rubber, black
  • one pieces will be needed
  • made in EU
4,82 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 7867
Repair parts for front axle and bushings

Silent buffer bush for wishbone

Silentbuffer bush fit to all chassis arms of Wartburg 353 and Wartburg 1,3 with the eye diameter 26mm.
  • upper wishbone, front axle - 2 pieces for each wishbone
  • lower wishbone, front axle - 2 pieces for each wishbone
  • wishbone, rear axle - 2 pieces for each wishbone

summary:
  • front axle: in all 8 pieces
  • rear axle: in all 4 pieces
11,05 €inclusive VAT, plus shipping costs
0temporary not available
temporary not available

Art.No. 6372

Metal bushing for buffer bearing bush of wishbone

Metall bushing to use in tandem with rubber for buffer bearing bush
Fit to all chassis arms of Wartburg 353 (new type of bearing bush)
Also fit to older types of bearing bushes if carry on using outer metal bushing of that.

  • best quality, made in Germany
  • upper wishbone, front axle - 2 pieces for each wishbone
  • lower wishbone, front axle - 2 pieces for each wishbone
  • wishbone, rear axle - 2 pieces for each wishbone

summary:
  • front axle: in all 8 pieces
  • rear axle: in all 4 pieces
5,96 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 6813

Rubber for buffer bearing bush of wishbone

Rubber bushing to use in tandem with metal bushing for buffer bearing bush
Fit to all chassis arms of Wartburg 353 (new type of bearing bush)
Also fit to older types of bearing bushes if carry on using outer metal bushing of that.

  • upper wishbone, front axle - 2 pieces for each wishbone
  • lower wishbone, front axle - 2 pieces for each wishbone
  • wishbone, rear axle - 2 pieces for each wishbone

summary:
  • front axle: in all 8 pieces
  • rear axle: in all 4 pieces
6,82 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 6812

Coil spring retainer for wishbone W353 /312

Lower suspension spring support for the front axle of the Wartburg 353 and 312.
The spring cup seat have to be mounted together with the shock absorber holder on top of the upper wishbone Wartburg 353 / 312. Fit at the front axle left and right hand.
  • delivery as an single part
  • surface: steel blank
  • for each car two pieces will be needed
  • good reporduction, made in Eu
46,93 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 7659

Ball joint for wishbone

Connection ball joint as a single part for repairing of the front axle (other wishbone and and the swivel bearing).
Fit to all Wartburg 312, 353 und 1,3 models. The joint is mounted at the upper and the bottom wishbone.
This part is an high quality reproduction made in Europe.
  • fit to Wartburg 312, 353 and 1.3 modells like Limousine, Tourist, Camping and Trans
  • delivery inclusive sealing cap
  • for each wheel side two pieces will be needed, total four pieces for each car

10x Mounting screw for ball joint (Art.-Nr.:7774)
2x Mounting nut for ball joint (Art.-Nr.:7716)
2x Locking plate for ball joint for wishbone (Art.-Nr.:7003)
26,52 €inclusive VAT, plus shipping costs
0temporary not available
temporary not available

Art.No. 3302

Mounting screw for ball joint

Hexagon bolt for the connection ball joint and upper and lower wishbone, front axle left and right hand.
Fit to all Wartburg 312, 353 und 1,3 models. The nut can be used for the upper and the bottom wishbone.
  • material grade: 10.9
  • delivery inclusive spring washer
  • 10 pieces will be needed
1,85 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 7774

Mounting nut for ball joint

Nut for the connection ball joint for the other wishbone and and the swivel bearing. Fit to all Wartburg 312, 353 und 1,3 models. The nut can be used for the upper and the bottom wishbone.
  • delivery inclusive spring washer
  • four pieces will be needed
2,23 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 7716

Locking plate for ball joint for wishbone

Locking plate for both outer mounting screws of ball joint for the other wishbone and and the swivel bearing. fit to all Wartburg 312, 353 und 1,3 models.
The joint is mounted at the upper and the bottom wishbone.
  • for each ball joint one piece will be needed
4,55 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 7003

sleeve for ball joint of wishbone

Replacement sleeve for ball joint of wishbones fit to all types of Wartburg 353 and 1.3.
Please note: only use for Reproducted ball joints. Does not for for originale ones!!!
  • one piece needed for each ball joint (2 pieces for each front axle side)
  • material: rubber
  • made in EU
5,12 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 6371
Mounting steering knuckle

screw for Steering knuckle leaver

hexagon head screw M10 x 45
fit to Wartburg 353 and Wartburg 1.3
  • tensile strength: 10.9
  • made in Germany
  • you will need 2 pieces for one steering knuckle leaver
1,85 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 6319

Look plate for steering knuckle leaver

Look plate for hexagon bolt steering knuckle leaver.
Right and left hand mountable.
fit to Wartburg 353 and Wartburg 1.3
  • sheet matal, *bone style*
  • made in Germany
  • you will need 2 pieces at all
2,54 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 7239

Driver for steering column

Steel driver for fabric joint for the connection of the steering column of the 353 und Wartburg 1.3 to the Steering column assembley.
  • sheet metal, galvaniced
  • two pieces will be needed for each car
  • made in Germany

Please use the button detais for the exploded view and find the right spare part.
Parts-No.: 53 01304 702
4,20 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 7244

Fabric washer, steering column

Rubber joint for the connection of the steering column of the 353 und Wartburg 1.3 to the Steering column assembley.
  • delivery inclusive 8 pieces of tubular rivet to reinforce the hole
  • one piece will be needed for each car
  • made in EU

Please use the button detais for the exploded view and find the right spare part.
Parts-No.: 53 08002 900
17,49 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 7068

Bearing for steering column

Bearing bush for steering column
  • made of plastic
  • fit to all chassis variants of Wartburg 353 and Wartburg 1,3
Parts-No.: 53 01308 618
3,28 €inclusive VAT, plus shipping costs
0temporary not available
temporary not available

Art.No. 7059

Rubber spring for end stop wishbone (W353/W1.3)

Black rubber spring for upper end stop of wishbone rear axle (wartburg 353 and 1.3) and for upper wishbone of front axle Wartburg 353 (maybe for Wartburg 1.3, too)
  • four pieces will be needed for complete rear axle of Wartburg 353 and 1,3
  • two pieces will be needed for both upper wishbones of Wartburg 353 front axle
Parts-No. 53 01200 406
13,39 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 7056

Rubber spring for end stop wishbone W353

Black rubber spring for end stop of the upper wishbone front axle Wartburg 353.
Fit to the right and left hand wishbone.
  • material: rubber, black
  • two pieces will be needed total
  • Reproduction made in EU
Parts-no. 53 01200 808
5,06 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 8491
Wheel bearings and sealing Wartburg

Wheel bearing 6009 C2

Outher ball bearing for the front and rear axle of Wartburg 353 und Wartburg 1,3
  • one piece needed for each wheel (four at all)
  • wheel beraing type: 6009 C2
  • made in Germany
26,39 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 3320

wheel bearing Wartburg, 6307 C2

Outher ball bearing for the Wartburg 353 und Wartburg 1,3.
Fit to the front and rear axle of all types.
  • one piece needed for each wheel(four at all)
  • wheel bearing type: 6307 C2
  • made in Germany
28,07 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 3325

Shim washer (rubber)

Shim rubber made of rubber. Mounting between outer ring of inner wheel bearing and bearing case.
Fit to the front and rear axle of Wartburg 353 and 1.3
  • New production made of our own mouldings
  • material: rubber, black
  • total 4 pieces will be needed
Parts-No. 53 01201 503
8,68 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 7008

Radial sealing 55 x 75 x 10 SL

Sealing with additional dust lip to protect the sealing lip to protect the wheel bearings at the front and rear axle.
This radial seal will be mounted at the outside of the wheel bearing housing (wheel side / wheel hub side)
  • material: NBR black
  • made in Germany
  • for the front axle 2 pieces and for the rear axle 2 pieces will be needed
  • Fit to the models: Wartburg 312, wartburg 353 und Wartburg 1,3
Made in Germany
reduced from 10,92 € to 8,50 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 3330
2+1
1+1

Shaft seal - universal shaft

Radial oel seal for wheel side he drive Wartburg 353 gearbox.
The sealing will be mounted at the inner side of the wheel bearing housing / steering knuckle (driveshaft side).
Fit the the left and right hand of the steering knuckle.
  • size: 45 x 60 x 7
  • material: NBR (Nitril-rubber)
  • with additional dust lip
  • made in Germany
  • two pieces will be needed (one for each drive shaft)
8,77 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 7002

Bolt for wheel bearing housing

Screw for mounting the wheel bearing case at the steering front axle left or right hand
W312, 353, 1,3
Hexagon socket-head screw like original made with strength class 10.9
  • Hexagon bolt
  • strength grade 10.9
  • surface galvaniced
  • delivery as an single part
  • fit for the front axle of Wartburg 312, 353 and 1.3
  • 8 pieces will be needed
2,85 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 8219

Wheel bearing set

Wheel bearing set for the front and rear axle of the Wartburg 353 and 1,3.
Set consist of:
  • 1x deep groove ball bearing:6009 C2
  • 1x deep groove ball bearing:6307 C2
  • 1x sealing ring
  • all components are made by german producers
  • for each car total 4 sets will be needed
58,36 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 7242

Pin for wheel nut Wartburg

Locking pin for the castle nut to lock the wheel hub - wheel bearing - connection.
The pin fit to the front axle drive shaft and to the rear axle kingpin.
  • fit to Wartburg 353 and Wartburg 1.3
  • delivery as an single
  • four pieces will be needed
0,25 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 8026

Wheel nut Wartburg

Castle nut for mounting the wheel hub - wheel bearing - connection.
The nut fit to the front axle drive shaft and to the rear axle kingpin.
  • fit to Wartburg 353 and Wartburg 1.3
  • delivery as an single part without pin
  • four pieces will be needed
3,84 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 8025

Centering washer dirve shaft

Special washer for centering the wheel hub and the drive shaft (wheel side).
Mounting place between castle nut and the wheel hub.
The washer fit to the front axle drive shaft.
  • fit to Wartburg 353 and Wartburg 1.3
  • delivery as an single part
  • material: steel, galvaniced
  • two pieces will be needed
original spare part number: 134 29 11 006 075 701
3,82 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 8174

Wheel hub, secound hand

Wheel hub for the Wartburg 353. Fit to the front and the rear axle.
99,50 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 7109

Sleeve rubber set outer universal shaft side

One kit of rubber boots and assambly parts for the outher drive shaft joint of the Wartburg 312, 353 and 1,3.
It is always one piece assembled form the outer side of the joint and one piece from the inner side.
Scope of delivery:
2x Rubber boot wheel side (LDM-Art.-Nr.:3147)
1x oel for the lubication of the outer joint (LDM-Art.-Nr.:6620)
2x Band clamp, long (LDM-part.-No.:6408)
2x Clamp (LDM-part.-No.:6780)
  • one kit will be needed for each drive shaft (total: 2 set)

additional needed tools for dismounting and mounting (not part of this offer):
1x Seeger ring pliers, external retaining rings 19-60mm (LDM-part.-Nr.:8322)
36,86 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 8223

Sleeve rubber (outer universal shaft side)

Rubber boot for the outher drive shaft joint of the Wartburg 312 and 353.
It is always one piece assembled form the outer side of the joint and one piece from the inner side.
This oel (Art.-Nr.:6619) have to be used for the lubication of the outer joint.
  • material: rubber, black
  • made in EU
  • delivery as an single part without mounting pats

Additional needed mounting parts (not scope of delivery of the rubber boot):
2x Band clamp, long (part.-No.:6408)
2x Clamp (part.-No.:7608)
additional needed tools for dismounting and mounting (not part of this offer):
1x Seeger ring pliers, external retaining rings 19-60mm (LDM-part.-Nr.:8322)
9,32 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 3147

ADDINOL gear box oil GS80W90 (GL125), 1 Litre

High-end-car-gearbox oil for Wartburg 353 and others vehicles
Made of german high-quality producer ADDINOL
  • for usability in countrys with mediterranean or tropical weather
  • needed volume for one gearbox of Wartburg 353: 1,8 Litre
  • corresponds with the old name of viskosity: GL125 (SAE 90 EP)
  • SAE 80W-90; API GL-4; MIL-L-2105

application:
  • Hypoid gears with small offset
  • manual gear change-, steering- and distributing gear boxes

Additional comment: Notes for used oil disposalLink opens in a new window.
15,15 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 6619

Band clamp , long

Rebound strap for mounting of sleeve rubbers of universal shafts
long band clamp (for example for mounting of sleeve rubber on shaft joint), for diameter from 40mm up to 110mm
application:
  • the band clamp have to bent around the sleeve rubber by hand, so that it clinging to the sleeve rubber in best way
  • fixing this position by hooking into
  • spanning the band clamp with a pincers
  • ready
3,81 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 6408

Snap ring sleeve rubber final drive

Circlip for mounting at the Wartburg 353 and Wartburg 1,3 drive shaft boot.
Can be used at the inner sleeve of the outside joint.
  • Two piece will be needed for each car

Needed plier for dismounting and mounting (not part of this offer):
1x Seeger ring pliers, external retaining rings 19-60mm (LDM-part.-Nr.:8322)
2,26 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 7680

Sleeve rubber set gear box side

One kit of rubber boot and assambly parts for the universal shaft gearbox side.
Fit for all universal shaft of the Wartburg 353 and Wartburg 312 right and left hand.
Scope ofe delivery:
1x Sleeve rubber set gear box side
2x Band clamp, long (part.-No.:6408)
2x Spring clamp (part.-No.:8222)
1x High performance grease with molybdenum, tube 100g (Art.-Nr.:6256)
  • one set will be needed for each drive shaft
28,84 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 8224

Sleeve rubber (inner side)

Rubber sleeve gearbox side for the right and left universal shaft.
Fit for all universal shaft of the Wartburg 353 and Wartburg 312
  • material: rubber, black
  • two pieces will be needed
  • made in Europe
  • delivery as an single part without mounting spring and mounting strap

Additional needed mounting parts (not scope of delivery of the rubber boot):
2x Band clamp, long (part.-No.:6408)
2x Spring clamp (part.-No.:8222)
1x High performance grease with molybdenum, tube 100g (Art.-Nr.:6256)
15,90 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 3148

Spring holder for rubber boot gearbox side

Spring clamp for mounting the rubber sleeve gearbox side at the drive shaft.
Fit for the right and left car side at all types of Wartburg 353 and Wartburg 312.
This part is an new reproduction made in Germany. Best replacement for the original one.
Made of stainless steel.
Simply to assamble also by mounted driveshaft.
4,91 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 8222

high performance grease with molybdenum, tube 100g

high load carrying capacity
low oxidation, suitable for longterm lubrication
resistant to water wash-out
good corrosion protection
protection against fretting corrosion
price 119,70 Euro / kg
11,97 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 6256

Wheel nut AM 12 x 1,5 cone collar

cink-coated wheel nut with cone collar for Trabant, Wartburg and all other vehicles with same bolts
  • thread: M12 x 1,5
  • spanner gap: SW 19 mm
  • replacement for original wheel nut with high quality
2,20 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 6338

Wheel nut set, AM 12 x 1,5 cone collar

One set of cink-coated wheel nut with cone collar for Trabant, Wartburg and all other vehicles with same bolts.
Kit consists of 16 pieces.
  • thread: M12 x 1,5
  • spanner gap: SW 19 mm
  • replacement for original wheel nut with high quality
1,25 € per piece
20,00 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 7498

Wheel nut set AM 12 x 1,5 cone collar, covered

One set of cink-coated wheel nut with bigger cone collar. The nut end is closed an cover the bolt against dirt and water. Usefull for Trabant, Wartburg and all other vehicles with same bolts.Extended hexagon.
One kit consist of 16 pieces.
  • thread: M12 x 1,5
  • spanner gap: SW 19 mm
1,69 € per piece
26,99 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 7499

Wheel nut AM 12 x 1,5 cone collar, covered

Cink-coated wheel nut with bigger cone collar. The nut end is closed an cover the bolt against dirt and water. Usefull for Trabant, Wartburg and all other vehicles with same bolts
extended hexagon
  • thread: M12 x 1,5
  • spanner gap: SW 19 mm
2,10 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 7297

Wheel nut set, AM 12 x 1,5 cone collar

One set of cink-coated wheel nut with bigger cone collar for Trabant, Wartburg and all other vehicles with same bolts.Extended hexagon.
One kit consist of 16 pieces.
  • thread: M12 x 1,5
  • spanner gap: SW 19 mm
1,69€ per piece
26,99 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 7500

Wheel nut AM 12 x 1,5 cone collar

cink-coated wheel nut with bigger cone collar for Trabant, Wartburg and all other vehicles with same bolts
extended hexagon
  • thread: M12 x 1,5
  • spanner gap: SW 19 mm
2,15 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 6339

wheel bolt 50mm with flat portion

Wheel bolt fit to the Wartburg 353 and 1.3 front axle with disc brake system. Inclusice one side cuted.
Please note:
The length of 50mm consist the length of thread and the length of knurling.
  • legth: 50mm
  • thread: M12 x 1,5
  • thread length: 37mm
  • knurling diameter: 14,5mm
  • knurling length: 7,5mm
Bitte beachten: Der Artikel ist im Geltungsbereich der StVZO nicht zugelassen. Nach Einbau erlischt die Betriebserlaubnis des Kraftfahrzeuges.
5,33 €inclusive VAT, plus shipping costs
0temporary not available
temporary not available

Art.No. 7677

wheel bolt 60mm with flat portion

Wheel bolt fit to the Wartburg 353 and 1.3 front axle with disc brake system. Inclusice one side cuted.
Please note:
The length of 60mm consist the length of thread and the length of knurling.
  • legth: 60mm
  • thread: M12 x 1,5
  • thread length: 48mm
  • knurling diameter: 14,5mm
  • knurling length: 7,5mm
Bitte beachten: Der Artikel ist im Geltungsbereich der StVZO nicht zugelassen. Nach Einbau erlischt die Betriebserlaubnis des Kraftfahrzeuges.
5,62 €inclusive VAT, plus shipping costs
0temporary not available
temporary not available

Art.No. 7202

wheel bolt 40mm

universel wheel bolt fit to Wartburg, Trabant and DDR trailers and campers
Please note:
The length of 40mm consist the length of thread and the length of knurling.
  • legth: 40mm
  • thread: M12 x 1,5
  • thread length: 28mm
  • knurling diameter: 14,5mm
  • knurling length: 7,6mm
Bitte beachten: Der Artikel ist im Geltungsbereich der StVZO nicht zugelassen. Nach Einbau erlischt die Betriebserlaubnis des Kraftfahrzeuges.
4,98 €inclusive VAT, plus shipping costs
0temporary not available
temporary not available

Art.No. 7200

wheel bolt 50mm

universel wheel bolt fit to Wartburg, Trabant and DDR trailers and campers
Please note:
The length of 50mm consist the length of thread and the length of knurling.
  • legth: 50mm
  • thread: M12 x 1,5
  • thread length: 38mm
  • knurling diameter: 14,5mm
  • knurling length: 7,6mm
Bitte beachten: Der Artikel ist im Geltungsbereich der StVZO nicht zugelassen. Nach Einbau erlischt die Betriebserlaubnis des Kraftfahrzeuges.
4,86 €inclusive VAT, plus shipping costs
0temporary not available
temporary not available

Art.No. 6450

wheel bolt 80mm

universel wheel bolt fit to Wartburg, Trabant and DDR trailers and campers
Please note:
The length of 80mm consist the length of thread and the length of knurling.
  • legth: 80mm
  • thread: M12 x 1,5
  • thread length: 68mm
  • knurling diameter: 14,5mm
  • knurling length: 7,5mm
Bitte beachten: Der Artikel ist im Geltungsbereich der StVZO nicht zugelassen. Nach Einbau erlischt die Betriebserlaubnis des Kraftfahrzeuges.
5,89 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 7203

Hub cap , plastic

Plastic cover for the inner hole of Wartburg wheel disk to cover the hub axle nut.
  • material: plastic, black
  • made in EU
  • for each wheel one piece will be needed
5,20 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 7042

puller for ball joint 18/38mm

gable width: 18 mm
max. lenght of ball joint axle: 38 mm

best use for track rod joints of Trabant and Wartburg.
59,10 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 6192

Hose for R13 tires

Hose insert for the Trabant and Wartburg tires.
Fit to 13 zoll wheels.
  • for tire size: 135,145,155/ 70 R13
  • scope of delivery with tire valve and cap
17,88 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 7416

wheel bolt 60mm

universel wheel bolt fit to Wartburg, Trabant and DDR trailers and campers
Please note:
The length of 60mm consist the length of thread and the length of knurling.
  • legth: 60mm
  • thread: M12 x 1,5
  • thread length: 48mm
  • knurling diameter: 14,5mm
  • knurling length: 7,5mm
Bitte beachten: Der Artikel ist im Geltungsbereich der StVZO nicht zugelassen. Nach Einbau erlischt die Betriebserlaubnis des Kraftfahrzeuges.
5,62 €inclusive VAT, plus shipping costs

Art.No. 7201
The complete offer in Front axle

* All prices inclusive VAT and plus shipping costs.
© 2003 - 2023 LDM-tuning.de
Ersatzteile für Trabant, Wartburg und Barkas