This site in german: Wartburg 353 > Ersatzteile > Bremsen > Bremse hinten 
You are here: > Wartburg 353> Spare parts> Brakes> Rear brake

Spare parts for rear wheel brake Wartburg 353

The complete offer in Spare parts for rear wheel brake Wartburg 353

Brake drum 30mm

Brake drum as an single part fit to the rear wheel brake system of the Wartburg 353W models with disk brake system at the front axle and to all kind of Wartburg 1,3.
This part is an good Reproduction made in Europe.
The brake drum belongs to brake shoes with the wide of 30mm.
  • material: cast steel
  • brake drum inside diameter: 230mm
  • bolt circle: 4x160mm
  • surface: blank
  • delivery as an single part without any mounting bits
  • 2 pieces will be needed

additional needed special tools for deassembly / assembly:
  • should the occasion arise wheel hub puller
49,90 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 3084

Brake drum- set 30mm

Brake drum kit consists of two pieces fit to the rear wheel brake system of the Wartburg 353W models with disk brake system at the front axle and to all kind of Wartburg 1,3.
This part is an good Reproduction made in Europe.
The brake drum belongs to brake shoes with the wide of 30mm.
  • material: cast steel
  • brake drum inside diameter: 230mm
  • bolt circle: 4x160mm
  • surface: blank
  • delivery as an single part without any mounting bits
  • 2 pieces will be needed

additional needed special tools for deassembly / assembly:
  • should the occasion arise wheel hub puller
88,40 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 8270

Brake drum ( single part ), 50mm

The brake drum fit only for Wartburg 353 (older model) with brake drum system at the fron axle.
technical details:
for brake shoewide is 50mm
for brake drum diameter: 230mm
bolt circle 4 x 160mm
Reproduction made in Europe
for each car 2 or 4 pieces will be needed
67,56 €inclusive VAT, plus shipping costs
0temporary not available
temporary not available

Art.No. 3074
30mm brake shoe singel parts and sets

Brake shoe with long lining

brake shoe single part for Wartburg 353 with disc brake system at the front axle and all models of Wartburg 1,3.

  • brake shoe wide 30mm
  • one piece will be needed for each wheel side
13,50 €inclusive VAT, plus shipping costs
0temporary not available
temporary not available

Art.No. 3085

Brake shoe with short lining

brake shoe single part for Wartburg 353 with disc brake system at the front axle and all models of Wartburg 1,3.

  • brake shoe wide 30mm
  • one piece will be needed for each wheel side
  • scope od delivery: without hand brake leaver and rivet bolt
13,50 €inclusive VAT, plus shipping costs
0temporary not available
temporary not available

Art.No. 6398

Brake shoe set complete

for Wartburg 353 and Wartburg 1.3
wide: 30 mm

contents:
2x brake shoe with short brake pad
2x brake shoe with long brake pad
2x rivet for brake cable holder
63,89 €inclusive VAT, plus shipping costs
0temporary not available
temporary not available

Art.No. 3086

Hand brake lever right, brake shoe

Brake lever for mounting the hand brake cable at the right rear brake.
The lever will be mounted at the rear brake shoe by rivet bolt.
Fit to all brake shoes wide 30mm and 50mm for Wartburg 353 and Wartburg 1,3.
14,88 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 7875

Hand brake lever left, brake shoe

Brake lever for mounting the hand brake cable at the left rear brake.
The lever will be mounted at the rear brake shoe by rivet bolt.
Fit to all brake shoes wide 30mm and 50mm for Wartburg 353 and Wartburg 1,3.
14,88 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 7874
Brake shoe sets 50mm

Brake shoe set, rear axle, inclisive leaver, 50mm

fit to Wartburg 353 rear axle, models with drum brakes at all wheels
wide: 50 mm

contents:
  • 4x brake shoe with long brake pad
  • 2x rivet for brake leaver
  • hand brake leaver
  • one kit will be needed
67,90 €inclusive VAT, plus shipping costs
Lieferbar innerhalb von 6-8 Wochen.

Art.No. 7294

Brake shoe set, rear axle, 50mm

fit to Wartburg 353 with drum brakes at all wheels
wide: 50 mm

contents:
  • 4x brake shoe with long brake pad
  • 2x rivet for brake leaver
  • one kit will be needed
45,70 €inclusive VAT, plus shipping costs
0temporary not available
temporary not available

Art.No. 6888

Rivet bolt for hand-brake lever

Rivet bolt for mounting the hand brake lever at the rear brake shoe (short lining).
Fit to Tarabant 601 and Trabant 1,1 rear axle, Wartburg 311,312,353,1.3 and Anhänger wie Qek, Intercamp, Oase, Camptorist, Klappfix.
  • material: steel, galvaniced
  • one piece for each rear brake
1,95 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 183

Holder for brake shoe, complete set

Retainer kit for break shoes to fix the 30mm and 50mm brake shoes at the brake base plate.
fit to follow brake systems:
  • 4 set for brake drum front axle Wartburg 353
  • 4 set for brake drum rear axle W353 and 1.3
  • 2 sets for trailer with brake shoe wide of 50mm (e.g. Bastei, Intercamp, Camptourist CT9)
12,88 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 8316

Holder single part steel

Spring bearing for the brake shoe holder can be used for Trabant 500- 601 front brake, Wartburg 353 and Wartburg 1,3.
  • material: steel
  • priece for each piece
  • two pieces will be needed for each brake shoe
  • delivery as an single part
3,83 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 7098

Pressure spring for brake shoes

Spring to fix the break shoes at the brake base plate.
fit to follow brake systems:
  • 4 pieces for brake drum front axle Wartburg 353
  • 4 pieces for brake drum rear axle W353 and 1.3
  • 4 pieces for brake drum front axle B1000 and B1000-1
  • 4 pieces for brake drum rear axle B1000, B1000-1
  • 2 pieces for trailer with brake shoe wide of 50mm (e.g. Bastei, Intercamp, Camptourist CT9)
  • delivery as an single part
  • made in Germany
2,83 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 8195

release spring for brake shoes, long

long version of release spring for break shoes
fit to follow brake systems:
  • brake drum front axle Wartburg 353 (two pieces for each wheel side)
  • brake drum rear axle W353 (one piece for each wheel side)
  • brake drum front axle B1000 (two pieces for each wheel side)
  • brake drum rear axle B1000 (one piece for each wheel side)
  • trailer with brake shoe wide of 50mm (e.g. Bastei, Intercamp, Camptourist CT9): one piece for each wheel side
3,18 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 6454

release spring for brake shoes, short

short version of release spring for break shoes
fit to follow brake systems:
  • brake drum rear axle Wartburg 353 (one piece for each wheel side)
  • brake drum rear axle B1000 (one piece for each wheel side)
  • trailer with brake shoe wide of 50mm (e.g. Bastei, Intercamp, Camptourist CT9): one piece for each wheel side
2,94 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 6455

rigth thrust rod for brake shoes

thrust rod fit to the right side of rear wheel brake

fit to follow brake systems:
  • rigth brake drum rear axle Wartburg 353 with brake shoe wide of 50mm (one piece)
  • right brake drum front axle B1000 (one piece)
  • rigth brake drum rear axle Multicar M22 (one piece)
24,31 €inclusive VAT, plus shipping costs
0temporary not available
temporary not available

Art.No. 6471

left thrust rod for brake shoes

thrust rod fit to the left side of rear wheel brake

fit to follow brake systems:
  • left brake drum rear axle Wartburg 353 with brake shoe wide of 50mm (one piece)
  • left brake drum front axle B1000 (one piece)
  • left brake drum rear axle Multicar M22 (one piece)
24,31 €inclusive VAT, plus shipping costs
0temporary not available
temporary not available

Art.No. 6472
Wheel brake cylinder original and repro

Wheel brake cylinder, rear brake

This brake cylinder for rear wheel brake fit to Wartburg 353 (with disc brake at the front axle) and Wartburg 1.3.
Can be used for all body types like Limousine, Tourist and Trans.
  • fit to brake shoes with the wide of 30mm
  • piston diameter 19mm
  • one piece will be needed for each wheel side
  • made in EU
27,12 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 3087

Wheel brake cylinder ATE, rear brake

This brake cylinder is made by ATE.
Fit for rear wheel brake fit to Wartburg 353 (with disc brake at the front axle) and Wartburg 1.3.
Can be used for all body types like Limousine, Tourist and Trans.
  • fit to brake shoes with the wide of 30mm
  • piston diameter 19mm
  • one piece will be needed for each wheel side
  • Producer: ATE
65,77 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 8447

Wheel brake cylinder, rear axle, original, D=19mm

Complete in Germany overhauled rear wheel brake cylinder with ring sleeves, brak-piston D=19mm.
Mark: IFA BHL
Fit to Wartburg 353 (with disc brake at the front axle) and Wartburg 1.3
  • fit to brake shoes with the wide of 30mm
  • scope of delivery: inclusive ring sleeves and bleeder screw)(break piston diameter: 19 mm
  • two pieces will be needed

For more informations to this exchange part please use the Detail button.
Delivery only in exchange! Please send in advance one brake cylinder original IFA to our company.
78,90 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 7237

Weel-brake cylinder, rear , W353 (old version)

Wheel brake cylinder for the Wartburg 353 rear axle.
This kind of brake cylnder fit to Wartburg 353 with brake drums at the front axle as well as some Wartburg 353 models form vintage 1975-1982 with disc brake system at the front axle.
Please note, if you have an Wartburg model between the vintage 75-82 you have to check out the kind of mounted wheel brake cylnder before you place an order (piston diameter 25,35 or 19mm)
technical details:
piston-diameter: 25,35 mm
connection thread for brake line: M10x1
for brake drum diameter: 230mm
for brake shoe wide: 50mm
Reproducion made in Europe
  • one piece will be needed for each wheel side
47,01 €inclusive VAT, plus shipping costs
Lieferbar innerhalb von 6-8 Wochen.

Art.No. 6198

Wheel brake cylinder, rear axle, original, D=25,35mm

Complete in Germany overhauled rear wheel brake cylinder with ring sleeves, brak-piston D=25,35mm.
Mark: IFA BHL
This kind of brake cylnder fit to Wartburg 353 with brake drums at the front axle as well as some Wartburg 353 models form vintage 1975-1982 with disc brake system at the front axle.
Please note, if you have an Wartburg model between the vintage 75-82 you have to check out the kind of mounted wheel brake cylnder before you place an order (piston diameter 25,35 or 19mm)
  • fit to brake shoes with the wide of 50mm
  • scope of delivery: inclusive ring sleeves, dust caps and bleeder screw)(break piston diameter: 25,35 mm
  • two pieces will be needed

For more informations to this exchange part please use the Detail button.
Delivery only in exchange! Please send in advance one brake cylinder original IFA to our company.
76,80 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 7315

Mounting screw wheel brake cylinder, rear axle, Wartburg

Hexagon bolt inclusive lock washer for mounting the rear brake cylinder at the drum brake base plate.
Fit to all kind of Wartburg models.
  • surface: zinc galvaniced
  • grade: 10.9
  • scope of delivery inclusive lock washer
  • two pieces will be needed for each wheel brake cylinder
0,95 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 7521

Brake piston seals and dust caps diameter: 19mm

Self repair kit, rear wheel brake cylinder 19,05mm

Sleeve set for refresh the rear wheel brake cylinder.
Reproduction by the original manufacture and the original tool.
Fit for Wartburg 353 and wartburg 1,3.
  • scope of delivery: 2x ring sleeve, 2x dust cap, 2x mounting srew, 1x bleeder screw inclusive cap
  • fit to brake piston diameter 19,05mm
  • made in Germany
  • one set will be needed for each wheel side rear
17,75 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 7833

Dust cap set for rear wheel brake cylinder 19,05mm

Rubber sleeve, for the outside of the wheel brake cylinder (set incl. 2 pieces ).
Reproduction by the original manufacture and the original tool.
Fit for Wartburg 353 and wartburg 1,3.
The dust cap protect the brake pistion against brake dust and moisture.
  • fit to brake piston diameter 19,05mm
  • made in Germany
  • one piece will be needed for each wheel side rear
8,50 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 7522

Ring sleeve, for rear wheel brake cylinder original, 19,05mm

Ring sleeve, for wheel brake cylinder (set incl. 2 pieces )
fit for Wartburg 353 and wartburg 1,3
  • fit to brake piston diameter 19,05mm
  • made in Germany
  • one piece will be needed for each wheel side rear
8,25 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 7149

Ring sleeve, for rear wheel brake cylinder, 19mm, EU

Made in Europe set of ring sleeve, for wheel brake cylinder (set incl. 2 pieces )
fit for Wartburg 353 and wartburg 1,3
for one wheel brake cylinder, rear axle Art.Nr. 3087
  • fit to brake piston diameter 19mm
  • one piece will be needed for each wheel side rear
  • reproduction EU
15,20 €inclusive VAT, plus shipping costs
Lieferbar innerhalb von 6-8 Wochen.

Art.No. 3088

Bleeder screw, rear - brake suddle front

Bleeder screw for rear wheel brake cylinder Rear wheel-brake cylinder piston = 19,05mm and Rear wheel-brake cylinder piston = 15,87mm Trabant 601, Trabant 1.1 and QEK-caravans.
The bleeder screw fit also to Brake suddle left hand and Brake suddle right hand Wartburg 353 and Wartburg 1,3.
3 pieces will be needed for each brake suddle.

thread: M8 X 1,25
2,45 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 214

Bleeder screw cap with tongue

Rubber cap with additional tongue fit to all offered bleeder screws
Protect the bleeder screw hole from dust and water.
The flap kibosh loosing the complete cap.
  • material: brake fluid resistant rubber
  • made in EU
1,68 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 8446

Bleeder screw cap

fit to all offered bleeder screws
Protect the bleeder screw hole from dust and water.
  • material: rubber
  • made in Germany
0,35 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 215
Brake piston seals and dust caps

Ring sleeve, rear axle 25,35mm, original

Original ring sleeve set for rear wheel brake cylinder type: CZ5.
Fit to all models of: Multicar M22, Barkas, Wartburg 311, 312, 313 and Wartburg 353 with brake drum system at the front axle.
  • fit to brake cylinder diameter 25,35mm
  • Comlete set for one wheel brake cylinder: 2x cap sleeve, 2x dust cap
  • all rubber seals ar mad in Germany
  • material: break fluid resistant rubber
  • One set will be needed for each wheel side rear
18,90 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 7232

Ring sleeve, for wheel brake cylinder, EU

Ring sleeve, for rear wheel brake cylinder.
Fit to all models of Barkas and Wartburg 353 with brake drum system at the front axle.
Comlete set for one wheel brake cylinder (incl. 2 pieces)
  • fit to brake cylinder diameter 25,35mm
  • One set will be needed for each wheel side rear
9,83 €inclusive VAT, plus shipping costs
0temporary not available
temporary not available

Art.No. 4209

Handbrake cable, complete

handbrake cable for for Wartburg (rear axle).
fit to all type of Wartburg 3 and 4 cylinder engine.
both cables are symmetric and have the same length
  • the complete lenght is 160 cm
  • 2 pieces will be needed
32,56 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 3090

Sealing plate for hand brake lever (W353/W1.3)

Sealing plate for hand brake lever mounted at the care frame - body.
Fit to all variants of Wartburg 311, 312, 313, 353 und 1.3 (4-takt)
This part is an new reproduction, best replacement for the original one. Made from our own produced moulding tool.
  • material: oel and grease resistant rubber (NBR), colour black
  • Reproduction in best quality
  • made in Germany
  • one piece will be needed for each car
27,80 €inclusive VAT, plus shipping costs
Lieferbar innerhalb von 6-8 Wochen.

Art.No. 7004

Brake hose, rear

brake hose for all type of Wartburg (rear brake)
  • length 200mm
  • one side with core thread port M10x1
  • other side with external thread port M10x1
  • one piece will be needed for each wheel side
11,14 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 3096

Brake hose retainer, original style

sacer spring for connection between flexible brake hose and brake pipe
  • surface bronzing
  • one piece for each screw joint will be needed
2,10 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 240

Brake hose retainer

sacer spring for connection between flexible brake hose and brake pipe
not the same design like the originale one (made for VW). This retainer can be also used for Trabant and Wartburg.
  • electrogalvanized, black
  • high quality made in Germany, spring metal
  • one piece for each screw joint will be needed
2,50 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 6624

Brake pressure regulatoring valve, Tourist

Complete pre-mounted spare part. Hydraulic part for infinitely variable adjustment of the brake pressure rear axle. Direct mechanical triggering from the cargo load.
Fit to all Wartburg 353 and 1,3 station wagon.
  • original spare part
  • colour mark: yellow
  • one piece will be needed
  • delivery without protecting bellow
45,50 €inclusive VAT, plus shipping costs
0temporary not available
temporary not available

Art.No. 6678

Brake pressure regulatoring valve, Limousine

Complete pre-mounted spare part. Hydraulic part for infinitely variable adjustment of the brake pressure rear axle. Direct mechanical triggering from the cargo load.
Fit to all Wartburg 353 and 1,3 Limousine.
  • original spare part
  • colour mark: blue
  • one piece will be needed
  • delivery without protecting bellow
45,50 €inclusive VAT, plus shipping costs
0temporary not available
temporary not available

Art.No. 6459

Protection bellows for pressure bar input brake pressure regulatoring valve

Protection bellows for Barkas and Wartburg
11,67 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 3094

Universal brake line made of steel, PVC-coated 5m, 4,75x0,7

Brakepipeline made of steel and plastic coated.
One set constists of 6mm x 0,7mm 5m long
for Trabant, Wartburg, Volkswagen
price 3,05 Euro / meter
15,25 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 262

Universal brake line, PVC-coated in 1 m pices max.5m, 6x0,7

Brakepipeline made of steel and plastic coated.
Dimensions: 6mm x 0,7mm maximum 5m long.
Fit to Trabant, Wartburg, Volkswagen.
Price per meter.
Price: 6,50 Euro / Meter
6,50 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 263

Screw-cap for brakeline 4,75x0,7 Wartburg and VW

Brake pipe screw for breakline with flanged type E.
Can be used for all brake lines made of steel or nickel-cooper alloy with outside diameter 4,75mm.
  • fit to Wartburg 353, Wartburg 1,3 and Opel (Vauxhall)
  • thread: M10x1,0
  • spanner gap: M10
  • useable for brake pipes: 4,75x0,7mm
0,89 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 6378

Universal brake line, CUNIFER 5m, 4,75x0,7

Brakepipeline made of NiCuFe material. Size 4,75 x 0,7 mm with length of 5m
Fit for many cars also for Trabant, Wartburg
priece 5,45 Euro / meter
37,01 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 6177

paste for brake cylinders

special lubricants paste for brake cylinders
no problems with brake fluid and rubber sleevs
commended for new wheel brake cylinders
price 96,39 Euro / kg
17,35 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 6204

Brake pipe spanner 10-11mm angled

Special tool for mounting or demounting of screw-cap for brakelines.
type: level angleded
Fit to brake screws SW10 and SW11.
12,47 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 7702

Brake pipe spanner 10-11mm, straight

Special tool for mounting or demounting of screw-cap for brakelines.
type: sraight
Fit to brake screws SW10 and SW11.
9,86 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 7703

Brake pipe spanner 12-13mm, straight

Special tool for mounting or demounting of screw-cap for brakelines.
type: sraight
Fit to brake screws SW12 and SW13.
12,43 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 7992

brake-cleaner 600ml

quick-cleaner for brake and clutch parts
  • FCKW free
  • volume: 600 ml
  • type: AD
  • delivery as an single spray
price 7,62 Euro / liter
4,57 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 6252

Brake-cleaner XXL 850ml

quick-cleaner for brake and clutch parts
  • FCKW, aceton free
  • volume: 850 ml
  • delivery as an single spray
price 5,29 Euro / liter
4,50 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 7898

Brake-cleaner, one packing unit, 12x Sprayer 600ml

Complete packing unit quick-cleaner for brake and clutch parts
  • FCKW free
  • content: 12x sprayer with volume of 600 ml
That implies a price of a single sprayer of 3,90 €price 6,50 Euro / liter
46,80 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 7033

Pressure spring spline end for brake shoes

Spring for the automatic adjuster of the break shoes at the brake base plate.
This spring press the look plate that the sliding element can work only in one direction.
fit to follow brake systems:
  • 4 pieces for brake drum front axle Wartburg 353
  • 4 pieces for brake drum rear axle W353 and 1.3
  • 2 pieces for trailer with brake shoe wide of 50mm (e.g. Bastei, Intercamp, Camptourist CT9)
  • delivery as an single part
  • made in Germany

additional needed tools for deassembly / assembly:
  • no special tools will be needed
2,30 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 8260
The complete offer in Spare parts for rear wheel brake Wartburg 353

* All prices inclusive VAT and plus shipping costs.
© 2003 - 2023 LDM-tuning.de
Ersatzteile für Trabant, Wartburg und Barkas