This site in german: Barkas B 1000 > Ersatzteile > Vorderachse 
You are here: > Barkas B 1000> Spare parts> Front axle

Front axle

The complete offer in Front axle

shock absorber

Telescopic buffer with mounting eyes on top and down for the Barkas B1000 and B1000-1 front axle.
Modell: Van, pick up, fire-engine-vans and ambulace
  • absorber type: A3-200-220/50
  • made in Germany
  • two pieces will be needed
132,40 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 6299

Rubber sleeve cushion for shock absorber 45mm

The bushing is pressed in to the eye of the shock absorber diameter size 45mm.
Fit to Multicar M22, M24, M25 (please check your lenght of the distace pipe!!!) and Barkas B1000 und B1000-1
  • 1x length inner sleeve: 32 mm
  • 1x rubber
  • made in Germany
  • 2 or 4 pieces will be needed
14,21 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 8194

Wheel bolt M14 x 1,5 for B1000, GDR forklift

Wheel bolt fit to Barkas B1000 and B1000-1. Fit also to some forklifters, trailers and spacial made vehicles (GDR production).
Please note:
The length of 60mm consist the length of thread and the length of knurling.
  • length: 41mm
  • thread: M14 x 1,5
  • thread length: 29mm
  • knurling diameter: 16mm
  • knurling length: 7mm
9,90 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 7494

Wheel nut AM 14 x 1,5

2,59 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 4524

summer tyre 6.70-13 P34

New produced reinforced summer tyre fit to Barkas B1000.
For each tyre one hose for wheel will be needed.

name of tyre: 6.70-13 6PR
name of tyre tread: P34 (original tread design)
163,76 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 6905

Tube for wheel

Tube fit to the Barkas B1000 und B1000-1 tyre 6.70 R13.
delivery without valve.
22,85 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 6241

Joints for track rods Barkas 

Track rod 14mm (cone 14 mm) Germany

Track rod as complete unit for Barkas B1000 und B1000-1 with ball joints made in Germany.
Ball joints with 1x right turn thread LDM-part.no.:7856 and 1x left turn thread LDM-part.no.:7855, for track rod and with 14mm-cone.
This spare part is produced in Germany in high quality.
  • diameter of the connection pipe D= 20 mm
  • delivery inclusice 1x track rod joint with right turn thread 14mm-cone and 1x track rod joint with left turn thread 14mm-cone, 2x clamp for mounting and locking
  • two pieces will be needed
  • all parts are manufactured in Germany
104,50 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 8248

Track rod complete with cone 16 mm, Germany

Track rod as complete unit for Barkas B1000 und B1000-1 with ball joints made in Germany.
Ball joints with 1x right turn thread LDM-part.no.:8043 and 1x left turn thread LDM-part.no.:8042, for track rod and with 16mm-cone.
This spare part is produced in Germany in high quality.
  • diameter of the connection pipe D= 22 mm
  • delivery inclusice 1x track rod joint with right turn thread 16mm-cone and 1x track rod joint with left turn thread 14mm-cone, 2x clamp for mounting and locking
  • two pieces will be needed
  • all parts are manufactured in Germany
104,50 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 8249

Ball joint for track rod 14mm, right hand (cone 14 mm) Germany

Ball joint with right turn thread for track rod and with 14mm-cone
This spare part is produced in Germany in high quality.
  • Cone: diameter from 12,7mm to 14mm, thread at the cone M10x1,0
  • thread steering rod side: M14x1,5 RIGHT turn, thread length: 55mm
  • Please note: every tie bare needs one ball joint with right turned thread and one ball joint with left turned thraead!
  • made in Germany
34,78 €inclusive VAT, plus shipping costs

Art.No. 7855

Ball joint for track rod 14mm, left hand (cone 14 mm) Germany

Ball joint with left turn thread for track rod and with 14mm-cone
This spare part is produced in Germany in high quality.
  • Cone: diameter from 12,7mm to 14mm, thread at the cone M10x1,0
  • thread steering rod side: M14x1,5 LEFT turn, thread length: 55mm
  • Please note: every tie bare needs one ball joint with right turned thread and one ball joint with left turned thraead!
  • made in Germany
34,78 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 7856

Ball joint for track rod 16mm, right hand (cone 14 mm) Germany

Ball joint with right turn thread for track rod and with 14mm-cone
This spare part is produced in Germany in high quality.
  • Cone: diameter from 12,7mm to 14mm, thread at the cone M10x1,0
  • thread steering rod side: M16x1,5 RIGHT turn, thread length: 55mm
  • Please note: every tie bare needs one ball joint with right turned thread and one ball joint with left turned thraead!
  • made in Germany
34,78 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 7700

Ball joint for track rod 16mm, left hand (cone 14 mm) Germany

Ball joint with left turn thread for track rod and with 14mm-cone
This spare part is produced in Germany in high quality.
  • Cone: diameter from 12,7mm to 14mm, thread at the cone M10x1,0
  • thread steering rod side: M16x1,5 LEFT turn, thread length: 55mm
  • Please note: every tie bare needs one ball joint with right turned thread and one ball joint with left turned thraead!
  • made in Germany
34,78 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 7699

Ball joint for track rod, right hand ( cone 16 mm ) Germany

Ball joint with right turn thread for track rod and with 16mm-cone
This spare part is produced in Germany in high quality.
  • Cone: diameter from 14,5mm to 16mm, thread at the cone M12x1,5
  • thread steering rod side: M18x1,5 RIGHT turn, thread length: 63mm
  • Please note: every tie bare needs one ball joint with right turned thread and one ball joint with left turned thraead!
  • made in Germany
39,02 €inclusive VAT, plus shipping costs

Art.No. 7697

Ball joint for track rod, left hand ( cone 16 mm ) Germany

Ball joint with left turn thread for track rod and with 16mm-cone
This spare part is produced in Germany in high quality.
  • Cone: diameter from 14,5mm to 16mm, thread at the cone M12x1,5
  • thread steering rod side: M18x1,5 LEFT turn, thread length: 63mm
  • Please note: every tie bare needs one ball joint with right turned thread and one ball joint with left turned thraead!
  • made in Germany
39,02 €inclusive VAT, plus shipping costs

Art.No. 7698

Ball joint for track rod, right hand ( cone 16 mm ) Germany

Ball joint with right turn thread for track rod and with 16mm-cone and connection thread M20.
This spare part is produced in Germany in high quality.
  • Cone: diameter from 14,5mm to 16mm, thread at the cone M12x1,5
  • thread steering rod side: M18x1,5 RIGHT turn, thread length: 70mm
  • Please note: every tie bare needs one ball joint with right turned thread and one ball joint with left turned thraead!
  • made in Germany
45,22 €inclusive VAT, plus shipping costs

Art.No. 6457

Ball joint for track rod, left hand ( cone 16 mm ) Germany

Ball joint with left turn thread for track rod and with 16mm-cone and connection thread M20L.
This spare part is produced in Germany in high quality.
  • Cone: diameter from 14,5mm to 16mm, thread at the cone M12x1,5
  • thread steering rod side: M18x1,5 LEFT turn, thread length: 70mm
  • Please note: every tie bare needs one ball joint with right turned thread and one ball joint with left turned thraead!
  • made in Germany
45,22 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 6458

Ball joint for track rod 18mm, right hand (cone 18 mm), Germany

Ball joint with right turn thread for track rod, right hand with 18mm-cone
big thread: M18x1,5
small thread (on top of cone): M14
This spare part is produced in Germany in high quality.
  • Please note: every tie bare needs one ball joint with right turned thread and one ball joint with left turned thraead!
41,22 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 4510

Ball joint for trak rod 18mm, left hand (cone 18 mm), Germany

Ball joint with right turn thread for track rod, left hand with 18mm-cone
big thread: M18x1,5
small thread (on top of cone): M14
This spare part is produced in Germany in high quality.
  • Please note: every tie bare needs one ball joint with right turned thread and one ball joint with left turned thraead!
41,22 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 4511

Ball joint for steering push rod, right hand ( cone 16 mm ) Germany

Joint with right thread connection for the push rod with cone 18mm.
This spare part is produced in Germany in high quality.
Please note: the push rod pipe is made with 1x inner left thread and on the other hand 1x inner right thread. The pipe outside diameter is about 24mm.
  • Cone: diameter from 14,5mm to 16mm, thread M12x1,5
  • thread push rod side: M20x1,5 RIGHT, tap length: 50mm
  • for each rod will be one left and one right ball joint needed
  • made in Germany
45,22 €inclusive VAT, plus shipping costs

Art.No. 6941

Ball joint for steering push rod, left hand ( cone 18 mm ) Germany

Joint with left tap connection for the push rod with cone 18mm.
This spare part is produced in Germany in high quality.
  • Cone: diameter from 14,5mm to 16mm, thread M12x1,5
  • thread push rod side: M20x1,5 LEFT, tap length: 50mm
  • for each rod will be one left and one right ball joint needed
  • made in Germany
45,22 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 6940

Ball joint for steering push rod, right hand (cone 18 mm), Germany

Joint with left tap connection for the push rod with cone 18mm.
This spare part is produced in Germany in high quality.
  • Cone: diameter from 16mm to 18mm, thread M14x1,5
  • thread push rod side: M20x1,5 RIGHT, tap length: 70mm
  • for each rod will be one left and one right ball joint needed
  • made in Germany
59,36 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 7604

Ball joint for steering push rod, left hand (cone 18mm), germany

Joint with left tap connection for the push rod with cone 18mm.
This spare part is produced in Germany in high quality.
  • Cone: diameter from 16mm to 18mm, thread M14x1,5
  • thread push rod side: M20x1,5 LEFT, tap length: 70mm
  • for each rod will be one left and one right ball joint needed
  • made in Germany
59,36 €inclusive VAT, plus shipping costs

Art.No. 7603

Between rod for steering

Between rod for Barkas B1000 and B1000-1.
Made in Germany with high quality rod ends !
  • cone rod end: 16mm
  • made in Germany
117,38 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 4512

Steering push rod ( cone 18 mm )

Complete componet of steering rod. Fit to Barkas B1000 and B1000-1. Delivery inclusive two universal joints (1x left tap nad 1x right tap with cone 18 mm).
  • lenght of the rod: 91 cm
  • diameter D= 24 mm
  • lenght from middle-middle ball joints: ca. 97 cm
  • scope of delivery incl. two clips to locking thr joints
  • one piece will be needed
  • all parts made in Germany
138,90 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 4513

Steering push rod ( cone 16 mm )

Complete componet of steering rod. Fit to Barkas B1000. Delivery inclusive two universal joints (1x left tap nad 1x right tap with cone 16 mm).
  • lenght of the rod: 91 cm
  • diameter D= 22 mm
  • lenght from middle-middle ball joints: ca. 97 cm
  • scope of delivery incl. two clips to locking thr joints
  • made in Germany
  • one piece will be needed
138,90 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 6648

Bolt for knuckle-long, complete with needle bearing

Set with bolt for upper side, fit to all B-1000 and B1000-1 (Barkas)
compelete set with needle bearing.
  • length of bolt: 101mm
  • diameter of bolt: 25mm
  • outer diameter of needle bearing: 37mm
  • length of needle bearing: 30mm
66,13 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 4514

Bolt for knuckle-short, complete with needle bearing

Set with bolt for down side, fit to all B-1000 and B1000-1(Barkas)
compelete set with needle bearing.
  • length of bolt: 86mm
  • diameter of bolt: 25mm
  • outer diameter of needle bearing: 37mm
  • length of needle bearing: 30mm
66,13 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 4515

Grease nipple for knuckle front axle

Lubricating nipple for the bolt-knuckle at the down and upper side of the front axle.
Fit to all Barkas B1000 and B1000-1
  • delivery as an single part
  • thread: M10x1mm
  • spanner gap: 11mm
  • total 4 pieces will be needed
1,31 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 8274

Grease nipple stainless steel, for knuckle front axle

Lubricating nipple made of stainless steel for the bolt-knuckle at the down and upper side of the front axle.
Fit to all Barkas B1000 and B1000-1
  • delivery as an single part
  • material: 1.4305 VA
  • thread: M10x1mm
  • spanner gap: 11mm
  • total 4 pieces will be needed
8,21 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 8553

Needle bearing for knuckle front axle

Bearing for the bolt-knuckle at the down and upper side of the front axle.
Fit to all B-1000 (Barkas)
Delivery as an single part.
  • diameter: 30mm
  • for bolt diameter: 25mm
  • outer diameter of needle bearing: 37mm
49,31 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 7748
1+1

Connection shaft right hand

85,00 €inclusive VAT, plus shipping costs
0temporary not available
temporary not available

Art.No. 4516

Connection shaft left hand

85,00 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 4517

Bushing for bearing

Plastic bushing as bearing for the connection shaft Barkas B1000 and B1000-1.
The bushings are made at the outside diameter with the standard oversize.
If you need an diffenent size we can manufacure you this bushings with inner and outside oversize. Please ask.
  • material: plastic with high mechanical strength and emergency operating features
  • four pieces will be needed
  • made in Germany
19,50 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 4518

Connection joint steering column

65,80 €inclusive VAT, plus shipping costs
0temporary not available
temporary not available

Art.No. 4519

Sleeve for push rod ( steering )

Rubber sleeve to protect the joint between steering column and steering gear.
Fit to all types of Barkas B1000 and B1000-1.
  • material: rubber, black
  • one piece will be needed
  • reproduction made in EU
7,50 €inclusive VAT, plus shipping costs
0temporary not available
temporary not available

Art.No. 4521

Safety plate steering gear leaver

Looking plate for the nut of the steering gear leaver at the shaft.
Can be used for Barkas B1000 and B1000-1
  • surface: galvanized
  • one piece will be needed
  • made in Germany
3,95 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 7735

Mounting nut steering gear leaver

Nut for mounting the steering gear leaver at the shaft.
Can be used for Barkas B1000 and B1000-1
  • one piece will be needed
3,95 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 7713

Steering gear complete overhauled

Pfand für Lenkgetriebe ( Altteil ), wird bei Rückgabe erstattet + 40Euro
+ 40 € Pfand
267,96 €inclusive VAT, plus shipping costs
0temporary not available
temporary not available

Art.No. 4520

Wheel hub, final drive

120,61 €inclusive VAT, plus shipping costs
0temporary not available
temporary not available

Art.No. 4522

Slotted nut

slotted nut AM60 x 1,5 mm for wheel hub, final drive
One piece for each wheel side (front)
35,92 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 6279

Hexagon slotted and castle nut

Hexagon slotted and castle nut M27 x 1,5 mm,
can be used for the front and rear axle.
One piece for each wheel side.
6,83 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 6283

Split pin 5 x 50

Split pin can be used for the front and rear axle Barkas B1000 and B1000-1.
proticion from the castlel nut drivenshaft front axle and wheel hub rear axle.
  • surface: electrogalvanized (silver)
  • 4 pieces will be needed
0,27 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 6280

Countersunk-head screw for brake drum

M8 x 16 mm
with hexagon socket
galvanized
Two pieces for each wheel side, used for front and rear axle
0,45 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 6281

Wheel rubber cap

Central cover for the wheel hub of the Barkas B1000 and B1000-1.
High quality reproduction.
  • material: rubber, black
  • for each car four pieces will be needed
24,28 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 4523

Wheel bearing front axle (30208)

Wheel bearing for the front axle Barkas B1000 and B1000-1.
This is an tapered roller bearing type 30208
The Barkas need two pices for each wheel side.
Mounting place: wheel bearing case and stud axle.
  • high quality, made by FAG
  • total 4 pieces will be needed


additional needed mounting parts (not incuded at this offer):
2x Radial sealing ring 85 x 105 x 10 (part.-no.:4542)
2x Castle nut M27 x 1,5 (part.-no.:6283)
2x Cotterpin 5 x 50 (part.-no.:6280)
1x high performance grease with molybdenum, tin 1kg (part.-no.:6349)
oder
1x multi-purpose grease, cartridge 400g (part.-no.:6311)

Required special tools for disassambly / assambly:
36,87 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 4525

Radial sealing 90 x 110 x 10

Radial sealing for Barkas -wheel baraing case front axle,
one piece for each wheel side.
16,54 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 4526

Radial sealing 90 x 110 x 10 with additional dust lip

Radial sealing for Barkas -wheel bearing case front axle,
one piece for each wheel side.

90x110x10
with additional dust lip (protect the sealing lip against wearout through dust)
17,80 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 6775

Mounting bolt for bearing retainer

Hexagon screw for mounting the brubber bearing retainer at the vehicle frame.
Can be used for Barkas B1000 und B1000-1
Mounting place at the front and rear axle.
For the front axle will be four pieces needed as well for the rear axle.
Strength class: 10.9
spanner gap: SW19
3,75 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 7610

Rubber bearing

Bearing for the wishbones of the Barkas B1000 and B1000-1.
The rubber will be installed at the wishbone and fixed by clamp at the car frame.
Please note: the rubber ring has an special form and assembly possition !
(click on details)
The bearing fits to the front and rear axle at all types and body variations of Barkas B1000 and B1000-1.
  • material: rubber, black
  • for the rear wishbones, two pieces will be needed
  • for the front wishbones, two pieces will be needed
  • made in Germany
  • please note the assembly-marks, see details
Reproduction made in Germany
29,11 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 4540

Rubber for shock wishbone

Buffer for the wishbone end position for the front and rear axle of the Barkas B1000 and B100-1 all types and models.
This part is an brilliant German reproduction. The rubber part is at the sizes and rubbermaterial equivalent to the original part and and good replacement.
  • at the rear axle 8 pieces will be needed
  • at the front axle 8 pieces will be needed
  • made in Germany
Rubber part made of your own moulding tool, made in Germany
8,71 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 6837

Sleeve rubber ( outer universal shaft side ), splited

Sleeve can be used for the models Barkas B1000 and B1000-1.
Fit to cars with douple hinge universal shaft and with single hinge driven shaft.
Can be mounted without disassembly the driven shafts.
  • material: rubber, black
  • delivery without equipment
  • made in EU
  • one piece will be needed for each wheel

additional needed parts:
19,68 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 4416

Sleeve rubber ( outer universal shaft side )

Sleeve can be used for the models Barkas B1000 and B1000-1.
Fit to all Barkas B1000 with douple hinge universal shaft and with single hinge driven shaft and Barkas B1000-1.
Mounting only after disassembly the driven shafts.
  • material: rubber, black
  • delivery without equipment
  • made in EU
  • one piece will be needed for each wheel

additional needed parts:
18,26 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 4417

Band clamp, plastic for sleeve rubber ( outer universal shaft side )

Clamp for rubber sleeve other universal shaft of Barkas B1000 and B100-1 and inner sleeve for Barkas with single hinge universal shaft.
  • material: plastic, black
  • length: 750 mm, width: 8 mm
  • made in Germany
  • 4 pieces will be needed for the type with single hinge drive shaft, 2 pieces will be needed for the type with double hinge drive shaft
3,81 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 8544

Band clamp for sleeve rubber ( outer universal shaft side )

Clamp for rubber sleeve other universal shaft of Barkas B1000 and B100-1 and inner sleeve for Barkas with single hinge universal shaft.
  • material: stainless steel
  • length: 680 mm, width: 8 mm
  • made in Germany
  • 4 pieces will be needed for the type with single hinge drive shaft, 2 pieces will be needed for the type with double hinge drive shaft
4,85 €inclusive VAT, plus shipping costs

Art.No. 6552

Sliding sleeve halves (universal shaft)

Sliding sleeve halves for mounting sleeve rubber (wheel side) at universal shaft of Barkas B1000 and B1000-1.
Delivery as an one paar (2 pieces).
For each drive shaft, one set of sliding pieces will be needed.
Price for one pair will be 45,60 €
54,15 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 6365

Sleeve rubber ( inner universal shaft side )

Rubber sleeve to protect the inner joint (gearbox side)of universal shaft.
Fit to to older drive shafts (singe hinge system) of Barkas B1000.
  • complete new production
  • made in EU
  • material: rubber, black
  • for each drive shaft one piece will be needed

Additional needed accessory:
14,26 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 4418

Band clamp for inner sleeve rubber ( inner universal shaft side )

Clamp for rubber sleeve inner universal shaft of Barkas B1000 with single hinge universal shaft.
  • material: stainless steel
  • length: 360 mm, width: 4,6 mm
  • made in Germany
  • 2 pieces will be needed
2,48 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 8010

Drive shaft overhauled

Complete overhauled driven shaft for Barkas B1000 and B1000-1.
Fit to the left and right hand.
  • overhauled spare part
  • old part have to be shiped to our company in advance!
exchange part
580,13 €inclusive VAT, plus shipping costs

Art.No. 4420

Woodruff key for outer universal shaft

Fitted key for outer stub axle for the final drive.
Barkas B1000, old version of drive shaft.
  • 2 pieces will be needed
3,50 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 8540
The complete offer in Front axle

* All prices inclusive VAT and plus shipping costs.
© 2003 - 2023 LDM-tuning.de
Ersatzteile für Trabant, Wartburg und Barkas