This site in german: Trabant 1.1 > Ersatzteile > Hinterachse 
You are here: > Trabant 1.1> Spare parts> Rear axle
Navigation

Rear axle

The complete offer in Rear axle

Disk wheel, overhauled 13 Zoll

51,83 €inclusive VAT, plus shipping costs
0temporary not available
temporary not available

Art.No. 984

Inner protection cap ( rubber ) for stub axle

Grease cap made of rubber. Mounting at the wheelbearing case rear axle. This rubber cap protect the rear wheel bearing against dust and moisture.
  • original spare part
  • two pieces will be needed
5,90 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 996

Stub axle, rear axle

Cylindrical stub axle for the Trabant 1,1 with slut for secure nut.
Good quality reproduction.
  • length inclusive threat 118mm
  • high quality, made in EU
  • 2 pieces will be needed

It can also installed at the Trabant 601 rear axle in connection with rear brake drum Trabant 1.1 or (rear brake drum with 4x100mm) to upgrate the bolt circle (for example 4x100mm).
47,01 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 1000

Nut for rear axle

Round nut to fix and secure the rear axle of the Trabant 1,1
The nut have to pressed in the groove of the rear axel after the mounting with the correct torque.
  • surface: galvaniced
  • Spanner gap: SW 36
  • Threat: M24x1,5mm
  • turning moment: 157 Nm - 196 Nm
  • for each rear wheel one piece will be needed
7,19 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 1003

washer for nut of rear axle (T1.1)

outer washer to mount below the round nut of rear axle
only fit to Trabant 1.1
dimensions:
  • inner diameter: ca. 26,3 mm (nominal diamter: 26 mm)
  • outer diameter: ca. 39,4 mm
  • thickness: 5 mm
  • surface: galvanized
0,98 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 6663

Special washer for nut of rear axle (T1.1)

Level washer between rear axle king pin and the brake drum (inner side).
It only fits to Trabant 1.1. German reproduction made from stainless steel.
dimensions:
  • inner diameter: ca. 26,3 mm (nominal diamter: 26 mm)
  • outer diameter: ca. 40,0 mm
  • thickness: 2 mm
  • material: stainless steel
  • surface: straight
3,32 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 6898

Cover for wheel disc hole T1.1

Black plastic cover for the wheel hub of the Trabant 1,1
  • fit to front axle and rear axle
  • original-design with IFA-trademark
  • one piece will be needed for each wheel
  • made in Europe
15,10 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 1001
Delivery only at advance payment.

Grooved ball bearing, rear axle

Single side covered ball bearing for the rear axle of the Trabant 1.1
Two pieces needed for each wheel of rear axle
20,66 €inclusive VAT, plus shipping costs

Art.No. 1002

Radial seal, rear axle 48x62x8

radial seal 48x62x8 for sealing of:
  • cylindrical and conical rear axle of Trabant 500, 600 and 601
  • cylindrical rear axle of Trabant 1.1
  • outer hinge shaft for front axle of Trabant 500, 600 und 601 (built up to April 1984)
  • high quality
  • for each wheel side you will need 1 piece
5,55 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 993
Delivery only at advance payment.

Radial seal, rear axle 48x62x8 with dust lip

radial seal 48x62x8 with dust lip for sealing of:
  • cylindrical and conical rear axle of Trabant 500, 600 and 601
  • cylindrical rear axle of Trabant 1.1
  • outer hinge shaft for front axle of Trabant 500, 600 und 601 (built up to April 1984)
  • high quality
  • with additional dust lip to protect the sealing lip for the brake dust
  • for each wheel side you will need 1 piece
5,90 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 6118

Rubber sleeve cushion for shock absorber coil spring

Rubber-matal-sleeve for mounting at the telescopic shock absorber for coil spring.
Fit to the rear axle of Trabant from vintage: 1988 and Trabant 1,1 all types.
  • for shock eyes with diameter: 34mm, lenght: 45mm
  • length of the metal sleeve: 50mm
  • made in Germany
12,05 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 8034

Shock absorber for coil spring, rear axle

Telescopic shock absorber for coil spring. Fit to the rear axle of Trabant from vintage: 1988.
This Trabi shocks are an new production in Germany. Best replacement for the original ones.
Fit to all Trabant 601 from vintage 1988 und Trabant 1.1 Limousine, Kombi, Tramp and Kübel.
scope of delivery:
  • complete pre-installed inclusive bushing at the bottom mounting eye
  • with retainer for the lower spring penholder bottom
  • surface: powder coated, black
  • delivery as an single part, without mounting bits
  • Made in Germany
70,54 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 1010

Pressure pice, shock absorber, coil spring, rear side

the pessure pice fit to Trabant 601 with coil spring rear side
from year april 1988
  • material: aluminium
  • two pieces will be needed
9,95 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 6360

Pressure piece, shock absorber, coil spring, rear side

the pessure piece fit to Trabant 601 with coil spring rear side
from year april 1988

  • material: plastic
  • two pieces will be needed
6,55 €inclusive VAT, plus shipping costs
0temporary not available
temporary not available

Art.No. 1011

Cap, shock absorber, coil spring, rear side

Upper rubber bearing for the suspension strut of rear axle (only for coil spring!)
  • Trabant 601 form vintage April 1988
  • Trabant 1,1 all models
  • two pieces will be needed
7,36 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 1012

Coil spring, rear side Limousine

Trabant helical spring for the rear axle from vintage august 1988 ownwards with Mc-Pherson system.
New German production with the exect size and spring constant like as original.
  • wire diameter: 11 mm
  • coil number: 8,5
  • demounted length: 317 mm
  • middle coil diameter: 98 mm
  • made in Germany
73,23 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 6630

Coil spring, rear side Universal

Trabant station wagon helical spring for the rear axle from vintage 8-88 ownwards with Mc-Pherson System.
New German production with the exect size and spring constant like as original.
  • wire diameter: 12 mm
  • coil number: 8,5
  • demounted length: 286 mm
  • middle coil diameter: 98 mm
  • made in Germany
77,97 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 6631

Protection pipe for shock absorber, rear axle (Limousine)

Upper coil spring retainer for the rear suspension. The metal holder will be mounted on top of the rear shock absorber.
Type: can be used for Trabant 601 and 1.1 Limousine.
Used (nor new) original spare part.
  • for each car two pieces will be needed
31,95 €inclusive VAT, plus shipping costs
0temporary not available
temporary not available

Art.No. 1013

Protection pipe for shock absorber, rear axle (estate car)

Upper coil spring retainer for the rear suspension. The metal holder will be mounted on top of the rear shock absorber.
Type: can be used for Trabant 601 and 1.1 Universal (estate car).
Used (nor new) original spare part.
  • for each car two pieces will be needed
31,95 €inclusive VAT, plus shipping costs
0temporary not available
temporary not available

Art.No. 6226

Holder for shocks coil spring, left hand

Bottom shock absorber socket for coil spring suspension rear axle.
The U-profile is mounted with two bolts on top of the rear axle assembly, left hand (driver side).
This part is original manufactured
fit to:
  • Trabant 601 from yaer april 1988
  • Trabant 1,1 all models
  • one piece will be needed
19,20 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 6362

Holder for shocks coil spring, right hand

Bottom shock absorber socket for coil spring suspension rear axle.
The U-profile is mounted with two bolts on top of the rear axle assembly, right hand (codriver side).
This part is original manufactured
fit to:
  • Trabant 601 from yaer april 1988
  • Trabant 1,1 all models
  • one piece will be needed
19,20 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 6361

Penholder bottom, rear axle

22,87 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 1014

Rubber-ring for rear axle, EU

Elastomer bearing will be mounted form top and from below at the rear axles.
For each wishbone four pieces will be needed.
The rubberbearing fit to all Trabant 500,600,601 and 1,1 rear axle right and left hand.
  • made in EU
  • for each car 8 pieces will be needed
8,55 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 7293

Rubber-ring for rear axle, original

Elastomer bearing will be mounted form top and from below at the rear axles.
For each wishbone four pieces will be needed.
The rubberbearing fit to all Trabant 500,600,601 and 1,1 rear axle right and left hand.
  • original spare part
  • for each car 8 pieces will be needed
9,50 €inclusive VAT, plus shipping costs
0temporary not available
temporary not available

Art.No. 1021

Bushing EU for rear axle

Metal reatainer for the rear axle of the Trabant.
Reproduction made in EU
Connection between rubber bearings and the rear axle at the car underfloor.
  • material: steel, galvaniced
  • made in EU
  • total 4 pieces will be needed
18,56 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 8539

Bushing for rear axle

Metal reatainer for the rear axle of the Trabant.
Connection between rubber bearings and the rear axle at the car underfloor.
  • material: steel, galvaniced
  • made in Germany
  • total 4 pieces will be needed
24,60 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 1022

Hexagon haed nut M12x1,75x 60mm

Hexagon bolt for mounting the rear axle wishbones Trabant 500, 600, 601, 1-1.
Please check the thread type 1,75mm or 1,5mm which is mounted at your car !
  • tightening torque: 98...127 Nm
  • strength class: 10.9
  • olive galvaniced
  • length: 60 mm
  • made in Germany
  • four pieces will be needed
4,46 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 8667

Hexagon haed nut M12x1,5x 60mm

Hexagon bolt for mounting the rear axle wishbones Trabant 500, 600, 601, 1-1.
Please check the thread type 1,75mm or 1,5mm which is mounted at your car !
  • tightening torque: 98...127 Nm
  • strength class: 10.9
  • olive galvaniced
  • length: 60 mm
  • made in Germany
  • four pieces will be needed
4,46 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 1020

Rear axle assembly, left hand

Rear axle wishbone Trabant 1,1 left hand. The meatal frame is complete new produced.
The brake anchor plate and the wheel bearing case is overhauled and pre mounted.
Fit for all Trabant 1.1 models (coil spring rear axle)
Please note: Delivery only in exchange.
  • Scope of delivery inclusive brake base plate
  • without add-on components like stub axle, wheel bearings, brake shoes, shock absorber holder ec.
  • one piece will be needed

For more informations to this exchange part please use the Detail button.
Delivery only in exchange! Please send one rear axle Traban right hand to our company in advance.
385,02 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 6352

Rear axle assembly, right hand

Rear axle wishbone Trabant 1,1 left hand. The meatal frame is complete new produced.
The brake anchor plate and the wheel bearing case is overhauled and pre mounted.
Fit for all Trabant 1.1 models (coil spring rear axle).
Please note: Delivery only in exchange.
  • Scope of delivery inclusive brake base plate
  • without add-on components like stub axle, wheel bearings, brake shoes, shock absorber holder ec.
  • one piece will be needed

For more informations to this exchange part please use the Detail button.
Delivery only in exchange! Please send one rear axle Traban right hand to our company in advance.
385,02 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 6353

Bearing for transverse and trailer arm

Rear axle bearing piont for welding in at the car body.
  • Original spare part
  • Fir for Trabant 601 and Trabant 1.1
  • total 4 pieces will be needed
55,22 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 1025

Plastic cap for wheel nut

plastic cup for wheel nuts
for all wheel nuts and wheel bolts with a spanner gap of 19mm
  • Material: plastic, black
  • same shape like original plastic cup for wheel nuts of Trabant 601
  • for each wheel, 4 pieces will be needed
2,05 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 6438

Plastic cap for wheel nut

Cap for wheel nuts and wheel bolts with a spanner gap of 19 mm.
Type with additional collar and hemisphere.
  • single part
  • PVC, black
  • for each car 16 pieces will be needed
0,45 €inclusive VAT, plus shipping costs
0temporary not available
temporary not available

Art.No. 1085

Plastic cap for wheel nut, chrom effect (set of 16 pieces)

plastic cup for wheel nuts
for all wheel nuts and wheel bolts with a spanner gap of 19mm
  • set of sixteen pieces
  • made of chromed plastic
  • made in EU
price for one piece: 0,43€
9,44 €inclusive VAT, plus shipping costs
0temporary not available
temporary not available

Art.No. 6430

Plastic cap set for wheel nut, black

cheapest type of plastic cap for all wheel nuts with a spanner gap of 19mm
  • material: made of black plastic
  • set consist of 20 pieces

The grip of the plastic cups on the wheel nuts is not the best. Additionall means should be used (for instance: adhesive lubricant, Art.No. 6255 or better universal housing seal, demountable, Art.No. 6258).
price for one piece: 0,66 €
13,01 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 6366

Plastic cap set for wheel nut, chrome

cheapest type of plastic cap for all wheel nuts with a spanner gap of 19mm
  • made of chromed plastic
  • set consist of 20 pieces


The grip of the plastic cups on the wheel nuts is not the best. Additionall means should be used (for instance: adhesive lubricant, Art.No. 6255 or better universal housing seal, demountable, Art.No. 6258).
price for one piece: 0,63 €
12,53 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 6367

Wheel nut AM 12 x 1,5 x 13

2,90 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 975
Delivery only at advance payment.

Hose for R13 tires

Hose insert for the Trabant and Wartburg tires.
Fit to 13 zoll wheels.
  • for tire size: 135,145,155/ 70 R13
  • scope of delivery with tire valve and cap
17,88 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 7416
Delivery only at advance payment.

winter tyre 145/80 R13 PNEUMANT

winter tyre fit for all types of Trabant made by the original manufacturer
  • tyre with good values in economy, safety and comfort

the pressure for the Trabant tyres type M+S (winter tyre)
Trabant 601 Limousine front axle: 23,21 psi
Trabant 601 Limousine rear axle: 23,21 psi - 26,11 psi
Trabant 601 Universal front axle: 23,21 psi
Trabant 601 Universal rear axle: 23,21 psi - 27,56 psi
49,80 €inclusive VAT, plus shipping costs
0temporary not available
temporary not available

Art.No. 6511

Summer tyre Diagonal 5.20-13 70P TL P36

Summer tyre made by Heidenau with original tire profile P36
Diagonal tyre.
  • tyre wide: 5,20
  • wheel diameter: 13"
  • New production made in Germany
  • delivery without tube for tires
104,10 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 6510
1+1

Pressure sleeve for wheel bearings

One pressure tubee to keep apart the inner rings of both ball bearings (6206 C2) from rear axle Trabant 601 (only with cylindrical stub axle form 03/1984) and Trabant 1.1 rear axle.
  • For one wheel will be needed 1 piece
  • material: steel, blank


For a Trabant with universal driven shaft-new type (601 and 1.1) you will need only 2 pieces for rear axle.
18,50 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 7975
Delivery only at advance payment.

Mounting bolt for coil spring shocks

Hexagon srew for mounting the shock absorbers on bottom of the rear axle left and right hand.
fit to:
  • Trabant 601 from vintage april 1988, Trabant 1,1
  • two pieces will be needed
  • scope of delivery complete with spring washer
  • grade: 10.9
3,94 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 8186
The complete offer in Rear axle

* All prices inclusive VAT and plus shipping costs.
© 2003 - 2024 LDM-tuning.de
Ersatzteile für Trabant, Wartburg und Barkas