Spare parts and accessories of the drive system

The complete offer in Spare parts and accessories of the drive system

Flexible shaft for speedometer

Detail

Flexible shaft for speedometer fit to all Trabant 1,1 with 4-stroke motor.

total lenght of the shaft: 920 mm
both ends are with tetrahedral tappet: 2,6 x 2,6 mm
connection screw joint: aluminium-nut
one piece will be needed

19,85 €inclusive VAT, plus shipping costs

Delivery in 1-3 days

Art.No. 1051

Rubber grommet for tachometer shaft

Detail

rubber grommet for flexible speedometer shaft
fit to all variants of Trabant 601 and 1.1

inner diameter: 7,5 mm
for hole diameter of: 25 mm
thickness: 7,5 mm
one piece will be needed

4,85 €inclusive VAT, plus shipping costs

temporary not available

Art.No. 6734

Outer joint for universal shaft

Detail

Outer joint for for constant velocity drive shaft Trabant for right or left hand.
Fit for Trabant 601 from April 1984 and Trabant 1.1

delivery inclusive boot
made in EU
2 pieces will be needed
Trabant 601 from vinatge 04/1984
Trabant 1,1

75,40 €inclusive VAT, plus shipping costs

Lieferbar innerhalb von 6-8 Wochen.

Art.No. 8432

Universal shaft complete, short

Detail

Drive shaft complete for Trabant 1,1 left hand.
The dive shaft is complete overhauled and pre-mountet.
Please send your Trabant 1,1 universal shaft short (dirver side) in advance to our company for reparing.

scope of delivery: mecanical parts overhauled-changed, new sleeve rubbers, spring clip, varnished
one piece will be needed

Overhaul part, please send the drive shaft in advance to our company

249,66 €inclusive VAT, plus shipping costs

Delivery in 14 days.

Art.No. 75

Universal shaft, long

Detail

Drive shaft complete for Trabant 1,1 right hand.
The dive shaft is complete overhauled and pre-mountet.
Please send your Trabant 1,1 universal shaft long (codriver side) in advance to our company for reparing.

scope of delivery: mecanical parts overhauled-changed, new sleeve rubbers, spring clip, varnished
one piece will be needed

Overhaul part, please send the drive shaft in advance to our company

249,66 €inclusive VAT, plus shipping costs

Delivery in 14 days.

Art.No. 6520

shaft spider for transmission shaft, T1,1 / W1,3 complete

Detail

Complete spare part shaft spider for the Trabant 1.1 and Wartburg 1.3 drive shaft.
Right and left side mountable.
Teeth at the drive shaft: 22
Please note: This three finger spider can be only used for the huge type of drive shaft joint. Outside diameter: 80mm

diameter spiderring: 30mm
diameter spider: about 70mm
For each universal shaft one piece will be needed
made in Europe

52,43 €inclusive VAT, plus shipping costs

Delivery in 1-3 days

Art.No. 669

Socket joint set (inner joint) for transmission shaft, complete (T1.1/W1.3)

Detail

complete set of socket joint for transmission shaft of Trabant 1.1 or Wartburg 1.3
spare part made made in EU.
set consist of:

Inner joint (sliding socket with external teeth stub shaft)
1x shaft spider
fitted rubber sleeve
set of band clamps (1x long and 1x short)
1x tube of special grease for transmission shafts

92,34 €inclusive VAT, plus shipping costs

Delivery in 1-3 days

Art.No. 6795

seeger lock ring 22 x 2 mm Detail Snap ring for mounting of the 6-ball constant velocity drive hinge at the drive shaft. Fit to the right and left hand outer tripode universal shaft side of the Trabant 1,1. number of part (spare part catalogue of Trabant 1.1): 03 30328 106
1,50 €inclusive VAT, plus shipping costs Delivery in 1-3 days Art.No. 6225

Sleeves for the inner joint drive shaft

Sleeve rubber-Set ( inner side ) small joint

Detail

sleeve rubber for universal shaft (gearbox side.
Used for the small joint, diameter: 70mm.
fit to Trabant 1.1, Wartburg 1.3 and Skoda Favorit (all 4-stroke)
size:

set consist of: 1x special joint grease, 2x straps, 1x rubber sleeve
made in Germany
inner diameter gearboxside: 69 mm
inner diameter universalschaft side: 19 mm
length 95 mm
for each universal shaft one piece will be needed

23,72 €inclusive VAT, plus shipping costs

Delivery in 1-3 days

Art.No. 7243

Sleeve rubber ( inner side ) big joint

Detail

Sleeve rubber for universal shaft (gearbox side)
fit to Trabant 1.1, Wartburg 1.3 and Skoda Favorit (all 4-stroke)
size:

inner diameter gearboxside: 82 mm
inner diameter universalschaft side: 19 mm
length 92 mm
for each universal shaft one piece will be needed

14,90 €inclusive VAT, plus shipping costs

Delivery in 1-3 days

Art.No. 662

Sleeves for the wheelside joint drive shaft

Sleeve rubber (outer tripode universal shaft side)

Detail

CV rubber sleeve for outer joint of universal shaft, constant velocity drive shaft for Trabant 601 from vinatge: april 1984 and Trabant 1,1 (without vintage delimitation).

material: Rubber, black
size: inner diameter hinge: 68 mm, inner diameter universal shaft: 18 mm, length 105 mm
made in EU
one piece will be needed for each drive shaft

12,80 €inclusive VAT, plus shipping costs

temporary not available

Art.No. 652

Sleeve rubber EU ( constant velocity drive shaft )

Detail

CV rubber sleeve set for outer joint of universal shaft, constant velocity drive shaft for Trabant 601 from vinatge: april 1984 and Trabant 1,1 (without vintage delimitation).
Sleeve made in Europe
contents:

1x sleeve rubber (Art.-No.: 653)
1x band clamp set (Art.-No.: 6394)
1x high performance grease (Art.-No.: 6256)

19,24 €inclusive VAT, plus shipping costs

temporary not available

Art.No. 6296

Sleeve rubber GKN ( constant velocity drive shaft )

Detail

1x sleeve rubber
1x high performance grease
1x band clamp big diamter
1x band clamp small diamter

25,90 €inclusive VAT, plus shipping costs

Delivery in 1-3 days

Art.No. 7512

Band clamp, short

Detail

Rebound strap for mounting of sleeve rubbers of universal shafts
long band clamp (for example for mounting of sleeve rubber on shaft joint), for diameter from 25mm up to 50mm
application:

the band clamp have to bent around the sleeve rubber by hand, so that it clinging to the sleeve rubber in best way
fixing this position by hooking into
spanning the band clamp with a pincers
ready

3,03 €inclusive VAT, plus shipping costs

Delivery in 1-3 days

Art.No. 6536

Rebound strap 4,6 X 360 mm

Detail

Strap for rubber sleeves.

material: stainless steel
made in Germany
4 pieces will be needed

2,48 €inclusive VAT, plus shipping costs

Delivery in 1-3 days

Art.No. 655

Band clamp set for sleeve rubber of universal shaft

Detail

Rebound strap set for mounting of sleeve rubbers of universal shafts
consist of:

long band clamp (for example for mounting of sleeve rubber on shaft joint), for diameter from 40mm up to 110mm
short band clamp to seal sleeve rubber on universal shaft, for diameter from 25mm up to 50mm

application:

the band clamp have to bent around the sleeve rubber by hand, so that it clinging to the sleeve rubber in best way
fixing this position by hooking into
spanning the band clamp with a pincers
ready

5,20 €inclusive VAT, plus shipping costs

Delivery in 1-3 days

Art.No. 6394

Socked spring

Detail

Sleeve spring (round) have to be pressed in the support for engine or gerabox retainer.

outside diameter: 75mm
length: 55mm
length of the mounting bushing inside: 68mm
diameter of the mounting bushing inside: 11mm
Trabant 1,1 one piece will be needed for engine-gerbox support front left hand
Wartburg 1,3 two pieces will be needed for engine support front and for gearbox support rear

70,77 €inclusive VAT, plus shipping costs

temporary not available

Art.No. 635

Socked spring - eccentric

Detail

Sleeve spring (round-eccentric) have to be pressed in the engine-gearbox support

Trabant 1,1 one piece will be needed for engine support rear

88,18 €inclusive VAT, plus shipping costs

temporary not available

Art.No. 636

Radial sealings gearbox (dirve shaft)

Oil seal gearbox casing - universal shaft left

Detail

Radial sealing with special oil return twist.
Please note: this seal can be only installed at the left hand (driver side)
Made for the Trabant 1.1 and Wartburg 1,3 gearbox.
Mounting place: differential gear - left hand universal shaft

seal with readvancing twist
type with additional dust lip
inside diameter: 40mm
outside diameter: 52mm
gauge: 7mm
left hand

10,90 €inclusive VAT, plus shipping costs

Delivery in 1-3 days

Art.No. 3153

Oil seal gearbox casing - universal shaft right

Detail

Radial sealing with special oil return twist.
Please note: this seal can be only installed at the right hand (codriver side)
Made for the Trabant 1.1 and Wartburg 1,3 gearbox.
Mounting place: differential gear - right hand universal shaft

seal with readvancing twist
type with additional dust lip
inside diameter: 40mm
outside diameter: 52mm
gauge: 7mm
right hand

10,90 €inclusive VAT, plus shipping costs

Delivery in 1-3 days

Art.No. 3152

Band clamp , long

Detail

Rebound strap for mounting of sleeve rubbers of universal shafts
long band clamp (for example for mounting of sleeve rubber on shaft joint), for diameter from 40mm up to 110mm
application:

the band clamp have to bent around the sleeve rubber by hand, so that it clinging to the sleeve rubber in best way
fixing this position by hooking into
spanning the band clamp with a pincers
ready

3,81 €inclusive VAT, plus shipping costs

Delivery in 1-3 days

Art.No. 6408

Front wall collar

Detail

Rubber sleeve to seal the hole of gear change rod to the bulkhead to the engine compartment.
Fit to all types of Trabant 1.1 and Wartburg 1.3

Material: rubber, black
reproducted part, EU

19,94 €inclusive VAT, plus shipping costs

Delivery in 1-3 days

Art.No. 697

Bearing bush in gear change rod

Detail

Plastic bearing bush fit to gearbox side end of gear change rod.
The plastic bushing for gear change rod will be mounted at the ball stud for gear selector shaft LDM-part no.: 8214.

one piece will be needed for one gear change rod
fit to Trabant 1,1 and Wartburg 1,3
Part-No.: 03 16129 001

14,88 €inclusive VAT, plus shipping costs

Delivery in 1-3 days

Art.No. 7039

Ball stud for gear selector shaft

Detail

Ball stud as single part.
Fit to all gear selectors at the Trabant 1.1 and Wartburg 1.3
This ball stud will be mounted at the plastic bushing for gear change rod LDM-part no.: 7039.

one piece will be needed for one gear change rod
delivery inclusive mounting nut
fit to Trabant 1,1 and Wartburg 1,3
Part-No.: 99 00244 143

5,56 €inclusive VAT, plus shipping costs

Delivery in 1-3 days

Art.No. 8214

Ball bearing for bell crank

Detail

Ball stud as single part for the bell crank 1x top and 1x bottom side.
Can be used for the original plastic ball holder (LDM-part no.:7038)
Fit to all gear selectors at the Trabant 1.1 and Wartburg 1.3
This bearings will be mounted at the gear change rod LDM-part no.: 8216.

two piece will be needed
delivery inclusive mounting nut
fit to Trabant 1,1 and Wartburg 1,3
Part-No.:

5,95 €inclusive VAT, plus shipping costs

Delivery in 1-3 days

Art.No. 8231

Ball holder for preselective rod

Detail

Ball holder for both ends of preselective rod (connection between gearbox and gear change rod)

two pieces will be needed for one preselective bar
fit to Trabant1,1 and Wartburg 1,3
Part-No. (Wartburg): 53 01304 405

4,60 €inclusive VAT, plus shipping costs

Delivery in 1-3 days

Art.No. 7038

Ball bearing for bell crank

Detail

Bearing for the bell crank consist of ball stud and ball holder.
Reclacement made of metal for the original plastic ball holder (LDM-part no.:7038)
Fit to all gear selectors at the Trabant 1.1 and Wartburg 1.3
This bearings will be mounted at the gear change rod LDM-part no.: 8216.

two piece will be needed
delivery inclusive mounting nut
fit to Trabant 1,1 and Wartburg 1,3
Part-No.:

5,83 €inclusive VAT, plus shipping costs

Delivery in 1-3 days

Art.No. 8215

Ball bearing for bell crank

Detail

one piece will be needed
scope of delivery inclusive 2x joint
delivery inclusive 2x mounting nut
fit to Trabant 1,1 and Wartburg 1,3
Part-No.:

14,90 €inclusive VAT, plus shipping costs

Delivery in 1-3 days

Art.No. 8216

bearing for gear shifting, complete Detail
86,06 €inclusive VAT, plus shipping costs Delivery in 1-3 days Art.No. 696

Radial sealings gearbox (clutch shaft)

Radial sealing D20 x 40 x 7

Detail

Shaft sealing in normal version without dust lip for cluthch-shaft gearbox side (gearbox input shaft).

fit to the vehicles Trabant 1.1, Wartburg 1.3 and B1000
without dust lip
made in Germany
one piece will be needed

6,31 €inclusive VAT, plus shipping costs

Delivery in 1-3 days

Art.No. 6069

Radial sealing D20 x 40 x 7 SL

Detail

Radial sealing with additional dust lip for clutch-shaft gearbox side for

Fit to:

Trabant 1.1
Wartburg 1.3
B1000 (2-stroke engine with new type of gear box) and B1000-1 (4-stroke)
made in Germany
one piece needed

6,72 €inclusive VAT, plus shipping costs

Delivery in 1-3 days

Art.No. 6388

Cluch cable complete Detail
28,66 €inclusive VAT, plus shipping costs Delivery in 1-3 days Art.No. 682

Bushing for Disengaging shaft ( for clutch ) T1,1

Detail

Guiding bushing for the lever shaft for the clutch of the Trabant 1.1 and Wartburg 1,3.
Mounting place: gearbox clutch void.

material: plastic
one piece will be needed
made in Europe

12,38 €inclusive VAT, plus shipping costs

Delivery in 1-3 days

Art.No. 7859

Disengaging shaft ( for clutch ) T1,1

Detail

Lever shaft for the clutch of the Trabant 1.1 engine.
Mounting place: gearbox clutch void.
Spare part is complete with lever for the clutch cable and two arms for the clutch disenger.