This site in german: Trabant 1.1 > Ersatzteile > Motor > Kühlsystem 
You are here: > Trabant 1.1> Spare parts> Engine> cooling system

cooling system

The complete offer in cooling system

Water pump and sealings Trabant 1.1

Water pump

Coolant pump inclusive sealing ring for four cylinder 4-stroke engines of follow vehicles:
  • Trabant 1.1
  • Wartburg 1.3
  • Barkas B1000-1
  • fit also to many Volkswagen with the engine block called 1100er
  • one piece will be needed

The water pump is the turing- and the tensioner pulley for the cam belt as well.
  • delivery inclusive sealing ring
  • best quality, made in Germany
  • one piece will be needed
59,21 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 716

Water pump kit

Set constists of 1x timing belt and 1x coolant pump inclusive sealing ring for four cylinder 4-stroke engines of follow vehicles:
  • Trabant 1.1
  • Wartburg 1.3
  • Barkas B1000-1
  • fit also to many Volkswagen with the engine block called 1100er
  • one piece will be needed

The water pump is the turing- and the tensioner pulley for the cam belt as well.
  • delivery inclusive sealing ring for water pump
  • best quality, made in Germany
  • one kit will be needed
68,06 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 8599

Seal for water pump

Single part rubber seal fit to water pump.
2,80 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 717

Seal for water pipe

Paper sealing for the cooling water pipe connection to the engine block, rear side water pump.
Fit ot Trabant 1.1, Wartburg 1.3 and Barkas B1000-1 with four stroke engines.
  • made in Germany
2,65 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 7483

Fan for radiator

electrical fan for radiator Trabant 1,1. complete with installing frame for radiator.
curency: 12V
  • made in Germany
  • one piece will be needed
77,77 €inclusive VAT, plus shipping costs
0temporary not available
temporary not available

Art.No. 6483

Radiator

Water cooler with aluninium ribs for the Trabant 1,1. Inclusive meatal cover plates for fixing at the lower front part and srew fitting for the temperatur sensor.
  • material: aluminium, steel (galvaniced)
  • made in EU
149,99 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 718

Thermo switch for radiator fan

The thermo switch for radiator fan is a make contact, which is screwed directly into the radiator.
  • It closes contact if temperature of coolant is about 95°C +/- 3K and it closes if temperature is about 89°C +/- 3K.
20,28 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 723

Coolant GLYSANTIN® Protect Plus, frost protection agent

coolant concentrate Protect Plus (G48), suitable for all popular makes of car
quality engine coolant such as Glysantin® Protect Plus provides all-season:
  • Corrosion protection
  • Overheating protection
  • Frost protection
  • Neutrality to rubber and plastics
  • Low foaming tendency
  • High chemical stability

Fit to the most coolant systems, for instance of Wartburg 353 and 1.3, Trabant 1.1 and Barkas B1000(-1).

Mixable with coolant G11 from Volkswagen.
NOT mixable with coolant G12 from Volkswagen!
price 12,24 Euro / liter
12,24 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 6716

closure for compensating tank

Cap with core thread for coolant fluid bottle of Trabant 1.1, Wartburg 353, Wartburg 1.3, Barkas B1000 and B1000-1, Multicar M24 and M25 with Cunewald engine.
  • delivery as an single part
  • material:plastic
  • new repoduction
  • one piece will be needed
8,82 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 6645

Sealing compensating reservoir / blow off valve

Special sealing ring between the blow off valve and coolant compensating reservoir.
This part is an new production made of ur own manufactured tool.
  • material: heater fluid,Glysantin restistant rubber
  • delivery as single part, without any mounting parts
  • one piece will be needed

This sealing fit to coolant reservoir (W353/B1000/M25) and coolant reservoir
as well for
an dem blow off valve 50kPa, blow off valve 100kPa and blow off valve 130kPa
This sealing is suitable for follow car types:
  • Trabant 1.1
  • Wartburg 353
  • Wartburg 1.3
  • B1000 and B1000-1
  • Multicar M25

Suitable accessory:
5,95 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 8474

blow off valve for compensating tank, 100kPa (T1.1)

Blow off valve for cooling water tank of Trabant 1,1.
It will be mounted under the reservior cap.
  • pressure: 100kPa
  • made in EU
  • one piece will be needed
13,54 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 720

compensating tank complete

coolant bottle for Trabant 1.1, delivery without closure and valve
  • original spare part
35,20 €inclusive VAT, plus shipping costs
0temporary not available
temporary not available

Art.No. 719

Hose connector 19mm, universal

Universal useable plastic connection tube for coolant hoses.
Best use for reparations of demaged hoses or tuning and modifications z.B. Trabant with Wartburg engine or VW engines.
Easy to install, just push the two ends of the hoses at tube and fix it with two clamps.
technical details:
  • diameter: 19mm
  • lenght of the connection side: 32mm
  • legth total: 75mm
  • material: plastic, temperatur and oel restistant, whithe
3,18 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 7432

Radiator hose set Trabant 1,1

Complete set oft coolant hoses to for the Wartburg 1.3
Fit to all types like Limousine, station wagon and Tramp.
Scope of delivery:
  • 1x radiator hose: Di=10mm, length: 810mm
  • 1x radiator hose: Di=15mm, length: 470mm
  • 1x radiator hose: Di=15mm, length: 570mm
  • 1x radiator hose: Di=15mm, length: 730mm
  • 1x radiator form hose: Di=12mm, length: 360mm
  • 1x radiator form hose: Di=12mm, length: 420mm
  • 1x radiator form hose: Di=18mm, length: 240mm
  • 1x radiator form hose: Di=18mm, length: 260mm
  • 1x radiator form hose: Di=18mm, length: 300mm
  • 1x radiator form hose: Di=30mm, length: 240mm
  • 1x radiator form hose: Di=30mm, length: 470mm
  • 1x radiator form hose: Di=30mm, length: 480mm
99,48 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 8117

compensating tank complete, universal

universal useable coolant bottle.
Scope of delivery complete with closure cap and integreated valve and switch for fluid lavel.
Two connections for the water hoses.
diamter connection down: 15mm
diamter connection on top: 8mm
Brillant replacement for the original spare part. Can be used for tuning and modificatios for example: Trabant with Wartburg engine or VW engines
41,98 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 7430

Coolant hose compensating tank - engine

Cooling water hose for connection between compensating tank (uppper side) and engine block.
Fit to Trabant 1,1 with 1100 ccm four stroke engine.
  • inside diameter: 17 mm
  • outside diameter: 26 mm
  • lenght: ca.38 cm
  • one piece will be needed

To depicting of the spare part place (technical exploded view) please click on the details.
11,24 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 6646

Coolant hose compensating tank - radiator

Cooling water hose for connection between compensating tank and radiator.
Fit to Trabant 1,1 with 1100 ccm four stroke engine.
  • inside diameter: 10 mm
  • outside diameter: 19 mm
  • lenght: ca.86 cm
  • one piece will be needed

To depicting of the spare part place (technical exploded view) please click on the details.
14,34 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 6647

Thermostat

These calorstat are fit for Trabant 1.1 and Wartburg 1.3.
Scope of delivery inclusive rubber sealing ring, which should be changed at every demounting of the thermal switches.
  • Reproduction in Germany
  • open up temperature: 84°C
  • basic diameter: 54 mm
  • valve diameter: 35 mm
  • length closed phase: 34mm
  • round sealing: 4x50x58
  • made in Germany
  • one piece will be needed
18,39 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 6418

Rubber seal for thermostat

O-ring seal for mechanical thermal switch. The seal should be changed after every demounting of the heat governor.
  • material: rubber
  • form: round
  • diameter: 4 mm x50 mm x 58 mm
  • one piece will be needed
1,49 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 722

Sealing ring for cooling water pipe

Rubber seal for the connection between water pipe and engine block water pump.
Fit to the cooling system of the Trabant 1.1, Wartburg 1.3 and B1000-1.
1,49 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 7419

Repair set thermostat housing

Self repair set of pipes for the thermostat case of the Trabant 1,1 and Wartburg 1,3.
Set consist of:
  • 2x tube with diameter 20mm
  • 2x tube with diameter 16mm
  • 1x tube with diameter 12mm
49,66 €inclusive VAT, plus shipping costs
0temporary not available
temporary not available

Art.No. 7452

Thermostat housing

The thermostat case is the centrally part of cooling system.
Both cooling loops are connected in the thermostat housing.
Depending on the engine temperature the thermostat opens the large cooling loop (through the radiator).
  • original spare part
without cap
39,83 €inclusive VAT, plus shipping costs
0temporary not available
temporary not available

Art.No. 6448

Sealing ring for Thermostat housing

Rubber seal for the connection between thermostat case and engine block.
Fit to the cooling system of the Trabant 1.1, Wartburg 1.3 and B1000-1.
1,49 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 7418

Thermo switch

Thermostat is mounted in thermotat housing
The thermo switch is a earthless closed-circuit current switch for warm running automatic.
It open if cooling water temperature is about 60°C.
27,13 €inclusive VAT, plus shipping costs
0temporary not available
temporary not available

Art.No. 850

Transmitter for temperature indication

transmitter for temperature indication is screwed into thermostat housing
14,04 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 851
1+1

Form hose - engine - radiator

Cooling water hose for connection between engine and radiator.
Fit to Trabant 1,1 with 1100 ccm four stroke engine.
  • inside diameter: 31 mm
  • outside diameter: 40 mm
  • lenght: ca.45 cm
  • one piece will be needed

To depicting of the spare part place (technical exploded view) please click on the details.
13,85 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 852

Form hose - heating system / thermostat housing

Cooling water hose for connection between thermostat terminal block and radiator for heating system.
Fit to Trabant 1,1 with 1100 ccm four stroke engine.
  • inside diameter: 15 mm
  • outside diameter: 25mm
  • lenght: ca. 47cm
  • one piece will be needed
13,40 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 7479

Form hose - thermostat housing / heating system

Cooling water hose for connection between thermostat terminal block and radiator for heating system.
Fit to Trabant 1,1 with 1100 ccm four stroke engine.
  • inside diameter: 15 mm
  • outside diameter: 25mm
  • lenght: ca. 51cm
  • one piece will be needed
13,40 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 7478

Form hose - thermostat housing

Cooling water hose for connection between wather pump and thermostat case.
Fit to Trabant 1,1 with 1100 ccm four stroke engine.
  • inside diameter: 34 mm
  • outside diameter: 42mm
  • lenght: ca.29 cm
  • one piece will be needed
12,95 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 6652

Form hose pipe - radiator

Cooling water hose for connection between indermediate pipe and radiator.
Fit to Trabant 1,1 with 1100 ccm four stroke engine.
  • inside diameter: 30 mm
  • outside diameter: 39 mm
  • lenght: ca.32 cm
  • one piece will be needed
20,74 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 853

Pipe connector

Metal pipe connection for the coolant hose LDM-part.no.:853 and coolant hose LDM-part.no.:854.
Fit to Trabant 1,1 with 1100 ccm four stroke engine.
  • material: stee, galvaniced
  • inside diameter: 27 mm
  • outside diameter: 34 mm
  • lenght: ca.10 cm
  • one piece will be needed
15,73 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 8400

Form hose engine - pipe

Cooling water hose for connection between engine and indermediate pipe.
Fit to Trabant 1,1 with 1100 ccm four stroke engine.
  • inside diameter: 30 mm
  • outside diameter: 39 mm
  • lenght: ca.35 cm
  • one piece will be needed
23,63 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 854

Cooling water hose suction pipe - thermostat

Cooling water hose for connection between suction pipe and thermostat case.
Fit to Trabant 1,1 with 1100 ccm four stroke engine.
  • inside diameter: 17 mm
  • outside diameter: 27 mm
  • lenght: ca.26-27 cm
  • one piece will be needed
19,61 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 855

Cooling water hose thermostat - suction pipe

Cooling water hose for connection between thermostat case and suction pipe.
Fit to Trabant 1,1 with 1100 ccm four stroke engine.
  • inside diameter: 10 mm
  • outside diameter: 18 mm
  • lenght: ca.22 cm
  • one piece will be needed
19,61 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 857

Cooling water hose thermostat - carburettor

Cooling water hose for connection between thermostat case and carburettor.
Fit to Trabant 1,1 with 1100 ccm four stroke engine.
  • inside diameter: 11 mm
  • outside diameter: 20 mm
  • lenght: ca.40 cm
  • one piece will be needed
8,88 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 856

Cooling water hose thermostat - carburettor

Cooling water hose for connection between thermostat case and carburettor.
Fit to Trabant 1,1 with 1100 ccm four stroke engine.
  • inside diameter: 11 mm
  • outside diameter: 21 mm
  • lenght: ca.35 cm
  • one piece will be needed
8,88 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 858

Coolant hose, 15 x 3,5mm (yard goods)

rubber coolant hose with textile inset (DIN 73411 7/79)
  • up to 6 bar
  • Inner diameter: 15 mm (0,59 inch)
  • Thickness of wall: 3,5 mm (0,138 inch)
  • up to 125°C
  • Outer layer (EPDM): resistance to oil, ozone and aging through heat
  • Inner layer (EPDM): resistance to antifreeze admixture and corrosion inhibitor

Deliverable as yard goods. If order two pieces of this article we will deliver one piece with a length of two Meter.
price 17,92 Euro / meter
17,92 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 6936

Coolant hose, 25 x 4,5mm (1 Meter)

Rubber coolant hose with textile inset (DIN 73411 7/79)
  • bup to 6 bar
  • Inner diameter: 25 mm (1 inch)
  • Thickness of wall: 4,5 mm (0,177 inch)
  • up to 125°C
  • Outer layer (EPDM): resistance to oil, ozone and aging through heat
  • Inner layer (EPDM): resistance to antifreeze admixture and corrosion inhibitor

Only obtainable in pieces of one Meter.
price 29,86 Euro / meter
29,86 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 6917

Coolant hose, 25 x 3,5mm (1 Meter)

rubber coolant hose with textile inset (DIN 73411 issue 1955)
  • working pressure: 3 bar
  • Inner diameter: 25 mm (1 inch)
  • Thickness of wall: 3,5 mm (0,138 inch)
  • Outer and inner layer made of black SBR-rubber quality
  • resistant against hot water with antifreeze admixture from -20°C up to +95°C

Only obtainable in pieces of one Meter.
Inexpensive alternative for coolant hose 25mm x 4,5mm with lower resistance against pressure and temperatureFit to many veteran cars, for instance Wartburg 311price 14,77 Euro / meter
14,77 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 6948
1+1

Paper selaing for radiator switch

Special paper sealing ring for the electrical radiator fan
Fit to:
Thermo switch for Wartburg 353 form May 1985 (part.-no.:7286)
Thermo switch for Wartburg 1,3 and Trabant 1,1 (part.-no.:723)
  • material: special sealing paper
  • one piece will be needed
1,72 €inclusive VAT, plus shipping costs
Delivery in 1-3 days

Art.No. 8352
The complete offer in cooling system

* All prices inclusive VAT and plus shipping costs.
© 2003 - 2021 LDM-tuning.de
Ersatzteile für Trabant, Wartburg und Barkas