Rear axle

The product category Trabant 1.1 > Spare parts > Rear axle is spread over 5 sites:

Disk wheel, overhauled 13 Zoll
51,83 €inclusive VAT, plus shipping costs temporary not available Art.No. 984

Inner protection cap ( rubber ) for stub axle

Detail

Grease cap made of rubber. Mounting at the wheelbearing case rear axle. This rubber cap protect the rear wheel bearing against dust and moisture.

original spare part
two pieces will be needed

5,90 €inclusive VAT, plus shipping costs

Delivery in 1-3 days

Art.No. 996

Stub axle, rear axle

Detail

Cylindrical stub axle for the Trabant 1,1 with slut for secure nut.
Good quality reproduction.

length inclusive threat 118mm
high quality, made in EU
2 pieces will be needed

It can also installed at the Trabant 601 rear axle in connection with rear brake drum Trabant 1.1 or (rear brake drum with 4x100mm) to upgrate the bolt circle (for example 4x100mm).

47,01 €inclusive VAT, plus shipping costs

Delivery in 1-3 days

Art.No. 1000

Nut for rear axle

Detail

Round nut to fix and secure the rear axle of the Trabant 1,1
The nut have to pressed in the groove of the rear axel after the mounting with the correct torque.

surface: galvaniced
Spanner gap: SW 36
Threat: M24x1,5mm
turning moment: 157 Nm - 196 Nm
for each rear wheel one piece will be needed

7,19 €inclusive VAT, plus shipping costs

Delivery in 1-3 days

Art.No. 1003

washer for nut of rear axle (T1.1)

Detail

outer washer to mount below the round nut of rear axle
only fit to Trabant 1.1
dimensions:

inner diameter: ca. 26,3 mm (nominal diamter: 26 mm)
outer diameter: ca. 39,4 mm
thickness: 5 mm
surface: galvanized

0,98 €inclusive VAT, plus shipping costs

Delivery in 1-3 days

Art.No. 6663

Special washer for nut of rear axle (T1.1)

Detail

Level washer between rear axle king pin and the brake drum (inner side).
It only fits to Trabant 1.1. German reproduction made from stainless steel.
dimensions:

inner diameter: ca. 26,3 mm (nominal diamter: 26 mm)
outer diameter: ca. 40,0 mm
thickness: 2 mm
material: stainless steel
surface: straight

3,32 €inclusive VAT, plus shipping costs

Delivery in 1-3 days

Art.No. 6898

Cover for wheel disc hole T1.1

Detail

Black plastic cover for the wheel hub of the Trabant 1,1

fit to front axle and rear axle
original-design with IFA-trademark
one piece will be needed for each wheel
made in Europe

6,87 €inclusive VAT, plus shipping costs

Delivery in 1-3 days

Art.No. 1001

Grooved ball bearing, rear axle Detail Single side covered ball bearing for the rear axle of the Trabant 1.1 Two pieces needed for each wheel of rear axle
20,66 €inclusive VAT, plus shipping costs Art.No. 1002

Radial seal, rear axle 48x62x8

Detail

radial seal 48x62x8 for sealing of:

cylindrical and conical rear axle of Trabant 500, 600 and 601
cylindrical rear axle of Trabant 1.1
outer hinge shaft for front axle of Trabant 500, 600 und 601 (built up to April 1984)
high quality
for each wheel side you will need 1 piece

5,55 €inclusive VAT, plus shipping costs

Delivery in 1-3 days

Art.No. 993

Radial seal, rear axle 48x62x8 with dust lip

Detail

radial seal 48x62x8 with dust lip for sealing of:

cylindrical and conical rear axle of Trabant 500, 600 and 601
cylindrical rear axle of Trabant 1.1
outer hinge shaft for front axle of Trabant 500, 600 und 601 (built up to April 1984)
high quality
with additional dust lip to protect the sealing lip for the brake dust
for each wheel side you will need 1 piece

5,90 €inclusive VAT, plus shipping costs

Delivery in 1-3 days

Art.No. 6118

The product category Trabant 1.1 > Spare parts > Rear axle is spread over 5 sites:

1 2 3 4 5
Show all products

* All prices inclusive VAT and plus shipping costs.

Rear axle

The product category Trabant 1.1 > Spare parts > Rear axle is spread over 5 sites:

Disk wheel, overhauled 13 Zoll